Table of Contents
Advertisement
Item Item value
37
DDR SSC Freq
38
Panel H.Flip
39
Panel V.Flip
40
Panel ABSwap
41
Watchdog
42
Backlight PWM freq.(Hz)
43
Backlight PWM Limit
44
VGA_TxRx_Mode
45
LVDS Driving
46
LVDS Format
47
Ziggo Aging
48
SPDIF
49
Standard PWM Gain
50
ECO PWM Gain
51
VGA port
52
Zero Detect Enable
53
Copy PQ table to TV
54
Headphone
55
EXIF_FACTORY
How to Exit the Factory mode
Use one of the following methods:
•
Select EXIT_FACTORY from the menu and press the "OK"
button.
Note: When the TV is switched "off" by a power interrupt, or
normal switch to "stand-by" while in the factory mode, the TV
will show up in "normal operation mode" as soon as the power
is supplied again. The error buffer will not be cleared.
5.2.5
Customer Service Mode (CSM)
Purpose
The Customer Service Mode shows error codes and
information on the TVs operation settings.The call centre can
instruct the customer (by telephone) to enter CSM in order to
identify the status of the set.This helps the call centre to
diagnose problems and failures in the TV set before making a
service call.
The CSM is a read-only mode; therefore, modifications are not
possible in this mode.
Specifications
•
Ignore "Service unfriendly modes".
•
Line number for every
line (to make CSM language independent).
•
Set the screen mode to full
screen (all contents on screen is visible).
•
After leaving the Customer Service Mode, the original
settings are restored.
•
Possibility to use "CH+" or "CH-" for channel surfing, or
enter the specific channel number on the RC.
How to Activate CSM
To activate CSM, press the following key sequence on a
standard remote control transmitter: "123654" (do not allow the
display to time out between entries while keying the sequence).
After entering the Customer Service Mode, the following items
are displayed.
Note: Activation of the CSM is only possible if there is no (user)
menu on the screen!
Contents of CSM
•
1.1 Set Type This information is very helpful for a
helpdesk/workshop as reference for further diagnosis. In
this way, it is not necessary for the customer to look at the
rear of the TV-set. Note that if an NVM is replaced or is
initialized after corruption, this set type has to be re-written
to NVM.
•
1.2 Production code Displays the production
code (the serial number) of the TV. Note that if an NVM is
Service Modes and Fault Finding
Default value
20"
22"
24"
32"
30KHz
on
on
on
off
on
on
on
off
off
off
off
off
5sec
150
150
150
150
20
off
3
3
3
3
VESA 8bit VESA 8bit VESA 8bit VESA 8bit VESA 8bit JEIDA
Press OK
On
98
98
98
98
100
on
on
on
off
on
on
on
off
Press OK
on
on
on
off
Press OK
39"
40"
42"
on
on
off
on
on
off
on
off
off
120
150
150
1
1
5
VESA 8bit VESA 8bit LVDS Format
10bit
100
100
97
off
off
off
off
off
off
on
on
on
replaced or is initialized after corruption, this production
code has to be re-written to NVM.
•
1.3 Installation date Indicates the date of the first
installation of the TV. This date is acquired via time
extraction.
•
1.4 SSB Gives an identification of the SSB as stored in
NVM. Note that if an NVM is replaced or is initialized after
corruption, this identification number has to be re-written to
NVM. This identification number is the 12NC number of the
SSB.
•
1.5 Display 12NC NVM read/write.
•
1.6 PSU 12NC NVM read/write.
•
2.1 Current Main SW Displays the built-in main software
version. In case of field problems related to software,
software can be upgraded. As this software is consumer
upgradeable, it will also be published on the internet.
•
2.2 Standby SW Displays the built-in stand-by processor
software version. Upgrading this software will be possible
via USB.
•
2.3 Panel Code Displays the Display Code number.
•
3.1 Signal Quality Analog/digital signal strength.
•
3.2 Child lock Not active / active. This is a combined item
for locks. If any lock (channel lock, parental lock) is active,
it is indicated as "active".
•
3.3 HDCP keys Indicates the validity of the HDMI keys (or
HDCP keys). In case these keys are not valid and the
customer wants to make use of the HDMI functionality, the
SSB has to be replaced.
How to Navigate
By means of the "CURSOR-DOWN/UP" knob (or the scroll
wheel) on the RC-transmitter, can be navigated through the
menus.
How to Exit CSM
To exit CSM, use one of the following methods.
•
Press the MENU/HOME button on the remote control
transmitter.
•
Press the POWER button on the remote control
transmitter.
•
Press the POWER button on the television set.
back to
div. table
TPN10.1E LA
5.
47"
Description
DDR SSC frequency
off
Flip panel
off
Flip panel
off
ABSwap panel
Watchdog
150
Backlight PWM frequency
Backlight PWM Limit
VGA_TxRx_Mode
5
LVDS Driving
Ziggo Aging
Enable/Disable SPDIF source
98
Standard PWM Gain
ECO PWM Gain
off
Enable/Disable VGA port
off
Zero Detect Enable
Copy PQ table to TV
on
Enable/Disable Headphone source
Exits the Factory mode
EN 29
2013-Oct-18
Hide quick links:
Advertisement
Table of Contents
