Table of Contents
Advertisement
electro magnetic compatibility (EMC)
& radio frequency interference (RFI)
RFI Filter Ratings
Type
Part number
A
4200-0010
B
4200-0027
C
4200-1051
D
4200-1071
E
4200-1111
F
4200-1171
G
4200-1302
Main Ratings
* Above 40 ° C (104 ° F), the current rating is
reduced by 1.6A/ ° C (0.88A/ ° F)
AC Supply Ratings
Voltage (phase-to-phase and phase-to-ground):
480V +10%
AC supply frequency: 48 to 62 Hz
Ground Leakage Current
The ground-leakage current, phase-to-phase and
phase-to-ground, when the AC supply is 400V at
50Hz is as follows:
CONDITION
Balanced
One phase disconnected
For other AC supply voltages and currents, scale
the value of leakage current proportionally.
Discharge Resistors
A and B: 330 KΩ internally between phases, with
the star point connected by a 1M resistor to ground.
C to G: 10 MΩ internally between each phase
and ground.
Maximum Current Overload
150% of rated current for 60 seconds.
Power
Max.
dissipation at
continuous
rated current
current
10A
25W
27A
40W
50A
60W
75A
100W
110A
120W
170A
150W
300A
300W
A
B
C to G
5.6mA
7.4mA
55mA
41mA
57.9mA
350mA
Ingress
Max. ambient
protection
temperature at
rated current
IP20
50°C (122°F)
IP20
50°C (122°F)
IP00
50°C (122°F)
IP00
50°C (122°F)
IP00
50°C (122°F)
IP00
40°C (104°F)
IP00
50°C (122°F)
Overall Dimensions
Filter type
Dimension
H
W
A
396mm
50mm
9 /16
15 /16
15
in
1
B
396mm
75mm
9 /16
15 /16
15
in
2
C
330mm
190 mm
13 in
7
1 /2
in
D
330mm
190mm
1 /2
13 in
7
in
E
440mm
200mm
17
5 /16
in
7
7 /8
in
F
490mm
200mm
1 /4
7 /8
19
in
7
in
G
380mm
495mm
5 /16
1 /2
14
in
19
Weights
FILTER TYPE
kg
A
2
B
2.7
C
7.4
D
8
E
12.3
F
16
G
35
Case
temperature rise
at rated current
<30°C (86°F)
<40°C (104°F)
<40°C (104°F)
<40°C (104°F)
<40°C (104°F)
<55°C (131°F)
<40°C (104°F)
D
113mm
7 /16
in
4
in
113mm
7 /16
in
4
in
145mm
5
11 /16
in
145mm
11 /16
5
in
145mm
5
11 /16
in
145mm
11 /16
5
in
250mm
13 /16
in
9
in
lb
5
6
16
18
27
35
77
25
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Unidrive Servo Series and is the answer not in the manual?
Questions and answers
Need to input parameters into a UNI2402 Unidrive for a Rover 346
Need to input parameters into a UNI2402 Unidrive for a Rover 346 To clarify, it is a Biesse Rover 346... a c&c Machine Thanks
The parameters for a Control Techniques UNI2402 Unidrive Servo can be input using the on-board keypad, a remote keypad, or through UniSoft, a Windows-based configuration software tool. The drive has logically organized menus where parameters can be set.
To input parameters:
1. Use the keypad to navigate through the menus.
2. Select the required function from the logically organized menus.
3. Adjust the parameter values as needed.
4. Save the changes to apply the new settings.
For a Rover 346, specific motor and operational parameters should be set according to the motor’s requirements, such as speed limits, acceleration/deceleration times, braking mode, and PID control settings. If using UniSoft, connect the drive to a PC and configure it through the software interface.
This answer is automatically generated