Sony ICF-C8WM Operating Instructions

4-155-637-11(1)
FM/AM
Clock Radio
Operating Instructions
Mode d'emploi (au dos)
ICF-C8WM
Dream Machine is a trademark of Sony Corporation.
Dream Machine est une marque de fabrique de Sony Corporation.
The  (play) and VOLUME + buttons have a tactile dot.
The " " mark in the display indicates that the "WALKMAN" or Sony Ericsson Phone function
No Power No Problem is a trademark of Sony Corporation.
is activated.
No Power No Problem est une marque de fabrique de Sony Corporation.
©2009 Sony Corporation
Printed in China
— Consult the dealer or an experienced radio/TV
technician for help.
WARNING
 Replace the battery for the clock backup with a
Sony CR2032 lithium battery, and the battery
for the remote commander with a Sony CR2025
lithium battery. Use of another battery may
English present a risk of fire or explosion.
 Battery may explode if mistreated. Do not
recharge, disassemble or dispose of in fire.
Owner's Record
 Dispose of used battery promptly. Keep away
(U.S. only)
from children.
The model number and the serial number are located on the Important Safety
bottom.
Instructions
Record the serial number in the space provided below. Refer
to them whenever you call upon your Sony dealer regarding
1) Read these instructions.
this product.
2) Keep these instructions.
Model No. ICF-C8WM
3) Heed all warnings.
4) Follow all instructions.
Serial No. ________________________________
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
For customers who purchased this product in the
7) Do not block any ventilation openings.
USA
Please register this product on line at Install in accordance with the manufacturer's
http://www.sony.com/productregistration.
instructions.
Proper registration will enable us to send you
8) Do not install near any heat sources such as
periodic mailings about new products, services,
radiators, heat registers, stoves, or other
and other important announcements. Registering
your product will also allow us to contact you apparatus (including amplifiers) that produce
in the unlikely event that the product needs
heat.
adjustment or modification. Thank you.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
WARNING
plug has two blades with one wider than the
other. A grounding type plug has two blades
To reduce the risk of fire or electric shock, do
and a third grounding prong. The wide blade
not expose this apparatus to rain or
or the third prong are provided for your safety.
moisture.
If the provided plug does not fit into your
To reduce the risk of fire, do not cover the
outlet, consult an electrician for replacement
ventilation of the apparatus with newspapers,
of the obsolete outlet.
tablecloths, curtains, etc. And do not place lighted
10) Protect the power cord from being walked on
candles on the apparatus.
or pinched particularly at plugs, convenience
To reduce the risk of fire or electric shock, do not
receptacles, and the point where they exit
expose this apparatus to dripping or splashing,
from the apparatus.
and do not place objects filled with liquids, such
11) Only use attachments/accessories specified by
as vases, on the apparatus.
the manufacturer.
Do not install the appliance in a confined space, 12) Use only with the cart, stand, tripod, bracket,
such as a bookcase or built-in cabinet. or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
Do not expose the batteries (battery pack or NOTES ON LITHIUM BATTERY
caution when moving the cart/apparatus
batteries installed) to excessive heat such as  Wipe the battery with a dry cloth to assure a
combination to avoid injury from tip-over.
sunshine, fire or the like for a long time. good contact.
 Be sure to observe the correct polarity when
As the main plug is used to disconnect the unit
installing the battery.
from the mains, connect the unit to an easily
 Do not hold the battery with metallic tweezers,
accessible AC outlet. Should you notice an
otherwise a short-circuit may occur.
abnormality in the unit, disconnect the main plug
13) Unplug this apparatus during lightning storms
from the AC outlet immediately. or when unused for long periods of time. If you have any questions or problems concerning
14) Refer all servicing to qualified service your unit, please consult your nearest Sony dealer.
The unit is not disconnected from the AC power
personnel. Servicing is required when the
source (mains) as long as it is connected to the
apparatus has been damaged in any way, such
wall outlet, even if the unit itself has been turned
Features
as power-supply cord or plug is damaged,
off.
liquid has been spilled or objects have fallen
You are cautioned that any changes or  Clock Radio with "WALKMAN" / Sony
into the apparatus, the apparatus has been
modifications not expressly approved in this
exposed to rain or moisture, does not operate Ericsson Phone compatible
manual could void your authority to operate this
normally, or has been dropped.  Wake or Sleep to "WALKMAN" / Sony Ericsson
equipment.
Phone / Radio
For the state of california, USA only
 Easy to set A-B alarm
CAUTION Perchlorate Material –special handling may apply, See
 2-5-7 day alarm
www.dtsc.ca.gov/hazardouswaste/perchlorate
Danger of explosion if battery is incorrectly
 LCD Brightness control
Perchlorate Material: Lithium battery contains
replaced. Replace only with the same type.
 Wireless Remote commander
perchlorate
Connecting the
Precautions
antenna
 Play the unit on the power source specified in
This symbol is intended to alert the user
to the presence of uninsulated "dangerous "Specifications. "
voltage" within the product's enclosure that To connect the AM loop
 To disconnect the AC power cord (mains lead),
may be of sufficient magnitude to constitute
pull it out by the plug, not the cord.
antenna
a risk of electric shock to persons.
 Since a strong magnet is used for the speaker,
This symbol is intended to alert the user to keep personal credit cards using magnetic coding The shape and the length of the antenna is
the presence of important operating and
or spring-wound watches away from the unit to designed to receive AM signals. Do not dismantle
maintenance (servicing) instructions in the
prevent possible damage from the magnet. or roll up the antenna.
literature accompanying the appliance.
 Do not leave the unit in a location near a heat
1
Remove only the loop part from the
source such as a radiator or airduct, or in a
NOTE
plastic stand.
place subject to direct sunlight, excessive dust,
mechanical vibration, or shock. 2 Set up the AM loop antenna.
This equipment has been tested and found to
 Allow adequate air circulation to prevent
comply with the limits for a Class B digital device,
internal heat build-up. Do not place the unit on
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection a surface (a rug, a blanket, etc.) or near
against harmful interference in a residential materials (a curtain) which might block the
ventilation holes.
installation. This equipment generates, uses and
 Should any solid object or liquid fall into the unit,
can radiate radio frequency energy and, if not
unplug the unit and have it checked by qualified
installed and used in accordance with the
personnel before operating it any further.
instructions, may cause harmful interference to
 To clean the casing, use a soft cloth dampened
radio communications. However, there is no
guarantee that interference will not occur in a with a mild detergent solution.
particular installation. If this equipment does  Never touch the wire of the external FM
antenna during a thunderstorm. Furthermore,
cause harmful interference to radio or television
immediately disconnect the AC power cord
reception, which can be determined by turning
from the radio.
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment
and receiver.
— Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.

CR2025
FM wire antenna Notes
 Do not attempt to charge the battery.
 If you are not going to use the remote
commander for a long time, remove the battery
to avoid any damage that may be caused by
AC power
leakage and corrosion.
cord
About the backup
battery
To keep accurate time, this unit contains a
CR2032 battery as a backup power source.
The battery keeps the clock and the alarm
operating in the event of a power interruption.
Note for customers in
Canada
The clock is preset at the factory, and its memory
is powered by the preinstalled Sony CR2032
battery. If the "AM 12:00" appears on the display
when the unit is connected to AC outlet for the
first time, the battery may be weak. In this case,
consult a Sony dealer. The preinstalled CR2032
battery is considered part of the product, and is
covered by the warranty. You are required to show
"Note for customers in Canada" (in this
instruction) to a Sony dealer in order to validate
the warranty for this product.
Note for customers in the
USA
If "AM 12:00" flashes in the display when the unit
is connected to AC outlet for the first time, the
battery may be weak. In this case, consult your
Sony dealer.
Knowing when to replace the
battery
When the battery becomes weak, "" appears in
the display.
If a power interruption occurs while the battery is
weak, the current time and alarm will be
initialized.
Replace the battery with a Sony CR2032 lithium
battery. Use of another battery may cause a fire or
explosion.
Replacing the battery
1
Keep the AC plug connected to the AC
outlet, remove the screw that secures the
battery holder at the bottom of the unit
using a screwdriver, and remove the
battery holder (see Fig.).
2
Replace a new battery in the battery holder
with the  side facing up (see Fig.).
3
Insert the battery holder back into the
unit and secure it with the screw
(see Fig.).
4 Press  (play), RADIO BAND, AUDIO IN
or SNOOZE/DATE/SLEEP OFF to turn
" " off in the display.

Note
When you replace the battery, do not disconnect
the plug from the AC outlet. Otherwise, the
calendar, current time, alarm and station presets
will be initialized.

The  and VOL + buttons have a tactile dot.

Reset button CR2032
3
Connect the cords to the AM antenna
terminals.
Cord (A) or cord (B) can be connected to
either terminal.
Insert the cord while
pushing down the
terminal clamp.
Only insert up
to here. 
B
A
4
Make sure the AM loop antenna is
connected firmly by pulling softly.
Adjusting the AM loop antenna
Find a place and an orientation that provide good If the time in the display is
reception.
incorrect after the battery is
 Do not place the AM loop antenna near the
unit or other AV equipment, as noise may changed (Reset)
result.
Press the reset button with a pointed instrument.
Tip
The reset button is in the small hole located near
Adjust the direction of the AM loop antenna for
the battery holder.
best AM broadcast sound.
Compatible
Preparing the remote
"WALKMAN" models
commander
Use the Oval attachment (supplied with your
Before using the card remote commander for the
"WALKMAN") when you connect it to this unit.
first time, remove the insulation film. If the Oval attachment is not supplied with your
"WALKMAN, " use one of the attachments
supplied with this unit. "WALKMAN" models
compatible with this unit are as follows.
Models using the Oval attachment
(supplied with your "WALKMAN")
When to replace the battery
NWZ-E440 series: NWZ-E443/E444/E445/
E443K/E444K
With normal use, the battery (CR2025) should
last for about six months. When the remote NWZ-S540 series: NWZ-S544/S545
commander no longer operates the unit, replace Models using the Type A attachment
the battery with a new one.
(supplied with this unit)
NWZ-E430 series: NWZ-E435F/E436F/E438F
NWZ-S630 series: NWZ-S636F/S638F/S639F/
S636FK
NWZ-S730 series: NWZ-S736F/S738F/S739F
NWZ-A720 series: NWZ-A726/A726B/A728/
A728B/A729
NW-A800 series: NW-A808/A806/A805
NWZ-A810 series: NWZ-A815/A816/A818 Notes on radio reception
 To activate Automatic DST/Summer Time
NWZ-A820 series: NWZ-A826/A828/A829/  Keep digital music players or mobile phones
adjustment again, press and hold CLOCK and
A826K/A828K/A829K away from the AM loop antenna or the FM
SNOOZE/DATE/SLEEP OFF at the same time
at least 2 seconds. antenna, as this may lead to reception
" " and "On" appear in the display to show interference.
that Automatic DST/Summer Time adjustment  When you are listening to the radio with a Sony
has been activated. The display returns to the Ericsson Phone connected to the unit,
interference with radio reception may occur.
Models using the Type B attachment clock.
 When you are listening to the radio while
(supplied with this unit)
charging a "WALKMAN" / Sony Ericsson
NWZ-S510 series: NWZ-S515/S516
Setting the clock manually
Phone, interference with radio reception may
NWZ-S610 series: NWZ-S615F/S616F/S618F
occur.
NWZ-S710 series: NWZ-S715F/S716F/S718F
1 Plug in the unit.
NWZ-X1000 series: NWZ-X1050/X1060
2 Playing a "WALKMAN"
Press and hold CLOCK for at least 2
seconds.
/ Sony Ericsson Phone
The year starts to flash in the display.
3
Press ALARM TIME SET + or –
You can enjoy "WALKMAN" / Sony Ericsson
Tip
repeatedly to set the year.
Phone music by connecting to this unit. To use a
The type of attachment is located on the bottom.
4 "WALKMAN" / Sony Ericsson Phone, refer to the
Press CLOCK.
On copyrights
user's guide of your "WALKMAN" / Sony
5
Repeat steps 3 and 4 to set the month,
 "WALKMAN" and are Ericsson Phone.
day, hour and minute, and then press
registered trademarks of Sony Corporation.
To select the connector of the
 All other trademarks and registered trademarks CLOCK.
are trademarks or registered trademarks of "WALKMAN" / Sony Ericsson
The seconds start incrementing from zero.
their respective holders. In this manual,
Notes Phone
™ ®
and marks are not specified.
 If you do not press any button for about
1 minute while setting the clock, the clock This unit has two connectors for a "WALKMAN"
setting will be canceled. and a Sony Ericsson Phone.
Compatible Sony
 A calendar is installed in this unit. When the Select the connector before using "WALKMAN" /
date is set, the day of the week is automatically Sony Ericsson Phone according to the following
Ericsson Phone models
procedures.
displayed.
SUN = Sunday, MON = Monday,
Compatible Sony Ericsson Phone models are as
Note
TUE = Tuesday, WED = Wednesday,
follows. A "WALKMAN" and Sony Ericsson Phone
THU = Thursday, FRI = Friday, SAT = Saturday
cannot be used at the same time.
Model(s) Available
To display the year and date
1
Pull the Docking Tray all the way out.
function(s)
Press SNOOZE/DATE/SLEEP OFF once for the
a C510/C510a/C702/C702a/ Alarm/
date, and press it again for the year.
C902/C903 Music After a while, the display will change back to the
G700/G700Busir/G900 playback/ current time automatically.
K530i/K550i/K550im/ Battery
K610i/K610im/K618i/ charge
Setting the brightness
K770i/K790a/K800i/
K810i
of the display
S500i
2
T650i/T700/T707/TM506 Three levels of brightness are available by pressing Press SELECT to select the
BRIGHTNESS/TIME ZONE.
V630i "WALKMAN" or Sony Ericsson Phone
W508/W580i/W595/ connector.
The indicator turns on to indicate the
W610i/W660i/W710i/
"WALKMAN" or Sony Ericsson Phone
W760a/W760i/W850i/
connector is activated.
Playing the radio
W880i/W980/W995/
W995a
–Manual tuning
Z610i/Z710i
b C901/C905 Music 1
Press RADIO BAND to turn on the radio
G502/G705/G705u playback/
and select the AM or FM band.
K310i/K320i/K510i/K630i/ Battery
2
Press TUNING + or – (TUNE + or – on
K660i/K750i/K850i charge
M600i the remote) to tune in to a desired
P1i/P990i
frequency.
V640i 3
Adjust the volume using VOLUME + or
W200i/W300i/W700i/
– (VOL + or – on the remote).
W705/W810i/W890i/
W902/W910i/W950i/
Tuning in to a station
Note
W960i
The Sony Ericsson Phone connector is selected by
The unit automatically scans AM or FM stations.
Z530i/Z550a/Z550i/Z558i
the default setting.
Z750i/Z770i 1 Press RADIO BAND to turn on the radio
To Play a "WALKMAN"
c F305 Battery to select the AM or FM band.
J110i/J120i charge 2
Press and hold TUNING + or – (TUNE +
1 Choose the "WALKMAN" attachment
K200i/K330
or – on the remote).
that fits your "WALKMAN" (see
R300
+: scans upward through the frequency bands.
"Compatible "WALKMAN" models").
S302/S312
–: scans downwards through the frequency
2
T250i/T280i/T303 Insert the tab on the left side of the
bands.
W302/W350i/W380i/W395
Scanning starts from the currently-tuned attachment (A) into the left slot in the
Z310a/Z310i/Z555i frequency. When a station is received,
"WALKMAN" connector, and then press
scanning stops.
down into the unit (B).
3
Adjust the volume using VOLUME +
Setting the clock for
or – (VOL + or – on the remote).
the first time
–Preset tuning
This unit is preset to the current EST (Eastern You can preset 20 stations for FM and 10 stations
Standard Time) at the factory, and is powered by a
for AM.
backup battery. All you need to do the first time is
Presetting a station
just plug it in and select your time zone.
3
Set your "WALKMAN" on the unit.
1 1
Plug in the unit. Follow steps 1 and 2 in "Manual tuning"
The current EST (Eastern Standard Time) to tune the frequency you wish to preset.
appears in the display. 2
Press and hold DISPLAY/MEMORY for
2
Press and hold BRIGHTNESS/TIME
at least 2 seconds.
ZONE for at least 2 seconds.
3 Press PRESET + or – to select the preset
Area number "2" flashes in the display.
number, then press DISPLAY/MEMORY.
3
Press ALARM TIME SET + or –
The frequency is stored with the selected
repeatedly to select the number as preset number.
follows:
Example: The following display appears
Area number Time zone when you preset FM 105.8 MHz to preset
number 1 for FM. The connector indicator blinks for a few
1 Atlantic standard Time
seconds and then stays lit.
2 Eastern standard Time
Notes
(default setting)
 The unit cannot operate while the connector
3 Central standard Time indicator is blinking.
 If the indicator does not stay lit, remove the
4 Mountain standard Time
"WALKMAN" and set again.
5 Pacific standard Time   When removing the "WALKMAN, " hold the
Docking Tray securely with one hand.
6 Yukon standard Time
4 Press  (play).
7 Hawaiian standard Time
" " appears in the display.
4
Press BRIGHTNESS/TIME ZONE to set.
The "WALKMAN" begins to play
Note automatically. You can operate the connected
Though the clock is correctly set at the factory, "WALKMAN" by this unit or the
discrepancies may arise during transport or The display shows the frequency for about "WALKMAN" buttons.
storage. If necessary, set the clock to the correct 10 seconds, and then returns to the current 5
Adjust the volume using VOLUME + or
time by referring to "Setting the clock manually. " time.
– (VOL + or – on the remote).
When Daylight Saving Time To preset another station, repeat these steps.
To
(summer time) begins Note
If you try to store another station with the same Stop playback
This model automatically adjusts for Daylight
preset number, the previously stored station will Go to the next track
Saving Time (summer time).
be replaced.
" " is displayed from the beginning of Daylight Go back to the previous
Saving Time (summer time) and disappears at the track
Tuning in to a preset station
end of Daylight Saving Time (summer time) Locate a point while
1
Press RADIO BAND to turn on the radio
automatically. listening to the sound
and select the AM or FM band.
 Daylight Saving Time (summer time) begins at:
2
2:00 AM on the second Sunday of March. Press PRESET + or – to select the desired
 Standard time begins at: 2:00 AM on the first
preset number.
Sunday of November.
3
Adjust the volume using VOLUME + or Tip
To cancel Automatic DST/Summer Time
– (VOL + or – on the remote). To remove the "WALKMAN" attachment, press
adjustment during the Daylight Saving
firmly down on the area marked (ooo) (A), and
Time (summer time) period –Auto preset tuning remove (B), as shown in the illustration.
The Automatic DST/Summer Time adjustment
1
can be canceled. Press RADIO BAND to turn on the radio
Press and hold CLOCK and SNOOZE/DATE/ and select the AM or FM band.
SLEEP OFF at the same time at least 2 seconds 2
Press and hold RADIO BAND until "AP"
while the clock is displayed.
appears in the display.
" " and "OFF" appear in the display to show that
3
Automatic DST/Summer Time adjustment has Press DISPLAY/MEMORY.
been canceled. The display returns to the clock. The unit automatically presets the available
Notes channels in order.
 Changes to Automatic DST/Summer Time
adjustment by the unit (see above) are subject
Improving the reception
to circumstances and laws in each country/
region. Should this interfere with desired
FM:
adjustment, cancel the Automatic DST/Summer
Extend the FM wire antenna fully to increase
Time adjustment and set the DST display
reception sensitivity.
manually as necessary. Customers living in a
AM:
country/region that does not use Daylight
Connect the supplied AM loop antenna to the
Saving Time (summer time) must cancel
unit. Rotate the antenna horizontally for
Automatic DST/Summer Time adjustment
optimum reception.
before using the unit.
To Play a Sony Ericsson 6
If "A" or "B" does not appear in the
Phone
display, press ALARM TIME SET A or B
again.
1
Set your Sony Ericsson Phone on the
The "WALKMAN" / Sony Ericsson Phone will
unit.
sound at the set time. With the alarm mode
The connector indicator blinks in a few
set to "WALKMAN" / Sony Ericsson Phone,
seconds and then stays lit (green).
when the alarm time met, if "WALKMAN" or
When your Sony Ericsson Phone is off, or if it
Sony Ericsson Phone is not attached to the
is listed in "Compatible Sony Ericsson Phone unit, the alarm sound will be the buzzer.
models" c , the indicator will turn red. In
Notes
this case, only battery charge function will be
 Select music library on your "WALKMAN" /
available (see "To use the unit as a battery
Sony Ericsson Phone with it connected to this
charger").
unit when you set the alarm mode to
Notes
"WALKMAN" / Sony Ericsson Phone.
 The unit cannot operate while the connector
 Power on the "WALKMAN" / Sony Ericsson
indicator is blinking.
Phone before connecting to this unit.
 If the indicator does not stay lit, remove the
Sony Ericsson Phone and set again.
 Setting the radio alarm
 Set Bluetooth function to off on the Sony
1
Perform steps 1 to 8 in "To set the
Ericsson Phone.
2 Press  (play).
alarm. "
" " appears in the display. 2
Press ALARM TIME SET A or B to select
The Sony Ericsson Phone begins to play
"RADIO" alarm mode.
automatically. You can operate the connected
"VOL" appears in the display.
Sony Ericsson Phone by this unit or the Sony
3
Press ALARM TIME SET + or – to adjust
Ericsson Phone buttons.
the volume.
Note
4
If the Sony Ericsson Phone is listed in Press ALARM TIME SET A or B.
"Compatible Sony Ericsson Phone models" b, Band ("FM" or "AM") or "– –" flashes.
certain operations may not be performed by the "– –" is the last station received.
buttons on this unit. In this case, operate with the 5
Press ALARM TIME SET + or – to select
buttons on the Sony Ericsson Phone.
the desired band or "– –. "
3 If you select "– –, " jump to step 8.
Adjust the volume using VOLUME + or
6
Press ALARM TIME SET A or B.
– (VOL + or – on the remote).
The preset number flashes.
7 Press ALARM TIME SET + or – to select
To Press
Stop playback OFF the desired preset number.
"WALKMAN" connector
The setting is entered.
Go to the next track  (forward)
Sony Ericsson Phone 8
If "A" or "B" does not appear in the
connector Go back to the previous  (backward)
display, press ALARM TIME SET A or B
track
again.
Locate a point while  (forward) or
The radio will turn on at the set time.
listening to the sound*
 (backward)
 Setting the buzzer alarm
while playing and
hold it until you
1
Perform steps 1 to 8 in "To set the
find the point.
alarm. "
* This function may not be available on some
2
Press ALARM TIME SET A or B to select
models. If the function does not work, press
"BUZZER" alarm mode.
 (play) to cancel.
The setting is entered.
Notes 3
If "A" or "B" does not appear in the
 The volume may be low when the volume of
display, press ALARM TIME SET A or B
Sony Ericsson Phone is set to low. In this case,
adjust the volume of Sony Ericsson Phone. again.
 When removing the Sony Ericsson Phone, hold The buzzer will sound at the set time.
the Docking Tray securely with one hand and Note
tilt the phone forward. The volume cannot be set for the buzzer alarm.
To confirm an alarm time setting
Press ALARM TIME SET + or –. The setting will
be displayed for about 4 seconds.
To change an alarm setting
Press and hold ALARM TIME SET + for at least
2 seconds to move the alarm time forwards. Press
and hold ALARM TIME SET – for at least
2 seconds to move the alarm time back.
To use the unit as a battery
When you release the button, the changed time
charger will be displayed for about 2 seconds. To change
the alarm time again, press ALARM TIME SET +
You can use the unit as a battery charger.
or – within these 2 seconds, otherwise the setting
Charging begins when the "WALKMAN" or Sony
change will be fixed as displayed.
Ericsson Phone is connected to the unit.
Charging status appears in the "WALKMAN" or To doze for a few more minutes
Sony Ericsson Phone display. For details, see the Press SNOOZE/DATE/SLEEP OFF.
user's guide of your "WALKMAN" or Sony The sound turns off but will automatically come
Ericsson Phone. on again after about 10 minutes.
You can change the snooze time by pressing
Note
SNOOZE/DATE/SLEEP OFF repeatedly within
A "WALKMAN" and Sony Ericsson Phone
4 seconds.
cannot be charged at the same time. Only the
The maximum length of the snooze time is
selected device (connector indicator on) can be
60 minutes.
charged.
To stop the snooze timer, press OFF/ALARM
RESET (OFF on the remote).
Setting the alarm
To stop the alarm
Press OFF/ALARM RESET (OFF on the remote)
This clock radio is equipped with 3 alarm to turn off the alarm.
modes—"WALKMAN" / Sony Ericsson Phone, The alarm will sound again at the same time the
radio and buzzer. Before setting the alarm, make
next day.
sure to set the clock (see "Setting the clock for the
To deactivate the alarm
first time").
Press ALARM TIME SET A or B to turn off the
Note
alarm A or B indicator from the display.
Alarm function is available only for the models
listed in "Compatible Sony Ericsson Phone
To activate the alarm
models" a.
Press ALARM TIME SET A or B to turn on the
To set the alarm
alarm A or B indicator in the display.
1 Notes
Press and hold ALARM TIME SET A or
 If the same alarm time is set for both alarm A
B for at least 2 seconds.
and B, alarm A takes priority.
"WAKE UP" appears and the hour flashes in
 If there is no operation while the alarm is
the display.
occurring, the alarm will stop after about
2
Press ALARM TIME SET + or –
60 minutes.
repeatedly until the desired hour
Note on the alarm in the event of a power
appears. interruption
In the event of a power interruption, the alarm
To cycle the hour rapidly, press and hold
will work until the battery is totally discharged.
ALARM TIME SET + or –.
However, certain functions will be affected as
3
Press ALARM TIME SET A or B.
follows:
The minute flashes.
 The backlight will not light up.
4
Repeat step 2 to set the minute.
 If the alarm mode is set to "WALKMAN" /
5 Press ALARM TIME SET A or B.
Sony Ericsson Phone or radio, it will change to
The days of the week flash. buzzer automatically.
6  If a power interruption occurs while the alarm
Repeat step 2 to set the days of the week.
is sounding, the alarm will stop.
You can select the days from the following
 If OFF/ALARM RESET is not pressed, the alarm
three options:
will sound for about 5 minutes.
Every day: SUN MON TUE WED THU FRI
 If "  " appears in the display, the alarm will not
SAT
sound in the event of a power interruption.
Week day: MON TUE WED THU FRI
Replace the battery if "  " appears.
Week end: SUN SAT
Press
 The snooze function will not work.
7
Press ALARM TIME SET A or B.
OFF  During a power interruption, each alarm will
The alarm mode setting is entered.
sound at the set time only once.
 (forward)
8
Press ALARM TIME SET + or –
 (backward)
repeatedly until the desired alarm mode
Setting the sleep timer
flashes.
 (forward) or
You can choose one of 3 settings: " , "
 (backward)
You can fall asleep to music, etc., using the built-
"RADIO" or "BUZZER. " Set the alarm mode
while playing and in sleep timer that turns off the unit automatically
as follows:
hold it until you
after a preset duration.
– " ": see " Setting the "WALKMAN" /
find the point.
Sony Ericsson Phone alarm. " 1
Press SLEEP while the unit is turned on.
– RADIO: see " Setting the radio alarm. "
"SLEEP" appears and the sleep time flashes in
– BUZZER: see " Setting the buzzer alarm. "
the display.
2
 Setting the "WALKMAN" / Sony Press SLEEP to set the sleep timer
Ericsson Phone alarm duration.
Each time you press SLEEP, the duration (in
1
Perform steps 1 to 8 in "To set the
minutes) changes as follows:
alarm. "
90 60 30 15
2
Press SELECT on the Docking Tray to
OFF
select the "WALKMAN" or Sony
The display returns to clock mode for about
Ericsson Phone connector.
4 seconds after you have finished the duration
3
Press ALARM TIME SET A or B to select
setting and released SLEEP, and then the sleep
alarm mode. timer starts.
" "
The unit will play for the duration you set, and
"VOL" flashes in the display.
then shut off.
4
Press ALARM TIME SET + or – to adjust
the volume. To turn off the unit before the preset
5
Press ALARM TIME SET A or B. time
The setting is entered. Press SNOOZE/DATE/SLEEP OFF or OFF/
ALARM RESET (OFF on the remote).
To change the sleep timer setting The "WALKMAN" / Sony Ericsson Phone
You can press SLEEP repeatedly to select the cannot be operated with this unit.
desired sleep timer setting even after the sleep  Make sure the "WALKMAN" or Sony Ericsson
Phone is securely connected.
timer has been activated.
 Make sure the Sony Ericsson Phone is listed in
To deactivate the sleep timer
"Compatible Sony Ericsson Phone models" a .
Press SLEEP repeatedly to set the sleep timer to
The "WALKMAN" / Sony Ericsson Phone
"OFF" in step 2.
cannot be charged.
 Make sure the "WALKMAN" or Sony Ericsson
Connecting external
Phone is securely connected.
equipment The indicator turns red when a compatible
Sony Ericsson Phone (listed in "Compatible
Sony Ericsson Phone models" a or b) is set
To listen to sound
in the unit.
1  Make sure the Sony Ericsson Phone is on.
Connect the AUDIO IN jack of the unit
to the line out jack or headphone jack of The indicator turns on (green), but the Sony
Ericsson Phone does not operate.
the external equipment using the audio
 Make sure the Sony Ericsson Phone is a
connecting cable (supplied).
compatible model (listed in "Compatible Sony
Ericsson Phone models" a or b ).
When Daylight Saving Time (summer time)
begins, the clock does not employ the
Daylight Saving Time automatically.
 Make sure the clock is set correctly.
 Press and hold CLOCK and SNOOZE/DATE/
SLEEP OFF simultaneously for at least
Audio connecting cable 2 seconds to activate the Automatic DST
(supplied)
function.
To external
equipment
Specifications
2
Press AUDIO IN to display "AUDIO IN. "
3
Play the equipment connected to the
Time display
AUDIO IN jack.
12-hour system
4
Adjust the volume using VOLUME + or – "WALKMAN" / Sony Ericsson Phone
section
(VOL + or – on the remote).
"WALKMAN":
To return to the radio
DC out: 5V
Press RADIO BAND. MAX: 500mA
The frequency is shown in the display. Sony Ericsson Phone:
DC out: 5V
To return to the "WALKMAN" / Sony
MAX: 600mA
Ericsson Phone
Radio section
Press  (play).
Frequency range
To stop listening
Band Frequency Channel step
Press OFF/ALARM RESET (OFF on the remote),
and stop playback on the connected unit.
FM 87.5 – 108 MHz 0.1 MHz
Notes AM 530 – 1 710 kHz 10 kHz
 Refer also to the connected equipment's manual.
General
 The supplied audio connecting cable may not
be used with some external equipment. In this Speaker
case, use a cord suitable for the external Approx. 3.8 cm (1 1 / inches) dia. 8 Ω
2
equipment you are using. Input
 When you listen to the radio with external AUDIO IN jack (ø 3.5 mm stereo minijack)
equipment connected, turn off the connected
Power output
equipment to prevent noise. If noise occurs,
0.8 W (at 10% harmonic distortion)
even when the equipment is turned off,
Power requirements
disconnect and place the external equipment
120 V AC, 60 Hz
away from the unit.
For clock back up: 3V DC, CR2032 battery (1)
Dimensions
Troubleshooting Approx. 167 × 124.7 × 97.1 mm (w/h/d)
(6 5 / × 4 15 / × 3 7 / inches) including projecting
8 16 8
parts and controls
Should any problem persist after you have made
Mass
the following checks, consult your nearest Sony
Approx. 988 g (2 lb 2.9 oz) including power
dealer.
supply unit
The clock flashes "AM 12:00" due to a power
Supplied accessories
interruption.
Remote commander (1)
 The battery is low. Replace the battery. Remove
AM loop antenna (1)
the old battery and install a new one.
Audio connecting cable (1)
The radio, "WALKMAN" / Sony Ericsson Attachment for "WALKMAN" (2)
Phone or buzzer alarm does not sound at the
Design and specifications are subject to change
preset alarm time.
without notice.
 Check that alarm "A" or alarm "B" is properly
displayed.
The radio or "WALKMAN" / Sony Ericsson
Phone alarm is activated but no sound comes
on at the preset alarm time.
 Check the alarm volume setting.
There is no sound from the "WALKMAN" /
Sony Ericsson Phone.
 Make sure the "WALKMAN" or Sony Ericsson
Phone is securely connected.
 Select music library on your "WALKMAN" /
Sony Ericsson Phone.
There is no sound from the Sony Ericsson
Phone.
 Make sure the Sony Ericsson Phone is listed in
"Compatible Sony Ericsson Phone models"
a
or .
b
 Power on the Sony Ericsson Phone.
 Adjust the volume of the Sony Ericsson Phone.
 Set Bluetooth function to off on the Sony
Ericsson Phone.
This warranty is valid only in the United States.
Cette garantie n'est valide qu'aux États-Unis.
This unit includes a preinstalled Sony Lithium battery (CR2032) as back-up power source for the clock, which is preset
to EST (Eastern Standard Time) at the factory. And this battery is considered part of the product.