Rear Panel - Sony BPU4800 Operating Instructions Manual

Baseband processor unit
Hide thumbs

Advertisement

Table of Contents
SHARE PLAY indicator
Indicates whether content can be shared using Share Play.
Flashing orange: Before genlock
Flashing green: Genlock operating
Solid green: Share Play enabled
i POWER switch and indicator
Turns the system power supply on/off to the unit, video
camera, and RCP-1000 series Remote Control Panel or
other device connected to the REMOTE connector. Switch to
ON to turn the power on, and switch to OFF to turn the power
off.
The indicator lights up when power is turned on.
j Network reset switch
Resets the IP address and network settings to their default
values. Insert and hold the end of a paper clip or other thin
object into the hole to operate the internal switch and then
start the unit. The SYSTEM indicator will begin flashing
purple.
k Optical signal condition indicators
Displays the communications link optical signal level
condition between the video camera, CCU, and the unit.
CAMTBPU: Signal level from the unit to the video camera
CAMtBPU: Signal level from the video camera to the unit
BPUTCCU: Signal level from the CCU to the unit
BPUtCCU: Signal level from the unit to the CCU
Indicates the receive signal status according to the following
indicators.
Two green indicators (right): Receive signal condition is
very good.

Rear Panel

a NMI-LAN connectors (SFP+)
These connectors output IP video signals and audio. The
output signal format is the same as the format set for the slot
of each connector.
b SHARE PLAY 1 to 2 connectors
Connects via a network switch to devices that support Share
Play for sharing content.
c GPIO (25-pin) connector
Parallel I/O connector.
For details, refer to the Maintenance Manual or Interface
Manual.
d TIME CODE IN connector
Inputs a time code generated by an external device.
GPIO (25P)
NETWORK 1
NETWORK 2
MAINTENANCE
IN
OUT
1/2
3/4
1
2
SHARE PLAY
TIME CODE
AUDIO (AES/EBU) IN
SLOT2 NMI
1
2
SLOT1 REPLAY NMI
1
2
SLOT1 REPLAY
SDI OUT 1
SDI OUT 2
SDI OUT 3
SDI OUT 4
SDI OUT 5
SDI OUT 6
SDI OUT 7
SDI OUT 8
SDI1
RCP/
REFERENCE
CNU
IN
OUT
One green indicator (2nd from right): Receive signal
condition is OK.
One yellow indicator (2nd from left): Receive signal level is
low.
One red indicator (left): Receive signal level is extremely
low.
l MENU control block
DISP/MENU lever and indicator
CANCEL/ENTER lever
MENU
DISP
CANCEL
MENU
ENTER
DISP/MENU lever and indicator: Used to display the status
and menu. The indicator lights up when the menu is
displayed.
CANCEL/ENTER lever: Used to cancel/enter settings when
the menu is displayed.
Control knob (rotary encoder): Used to switch pages when
the status screen is displayed. Used to move the cursor
within a page and to change the setting of the selected
item when the menu is displayed.
Pushing the control knob has the same function as setting
the CANCEL/ENTER level to ENTER.
m Menu lock switch
Locks the menu control block on the front panel.
MAINTENANCE
5/6
7/8
1/2
3/4
5/6
7/8
REMOTE 1/2
AUDIO (AES/EBU) OUT
SLOT1 LIVE NMI
1
2
SLOT1 LIVE
SDI OUT 1
SDI OUT 2
SDI OUT 3
SDI OUT 4
SDI OUT 5
SDI OUT 6
SDI OUT 7
SDI OUT 8
SLOT1 REPLAY
SLOT2 REPLAY
SLOT3 LIVE
SLOT2 LIVE
SDI2
SDI OUT
SDI OUT 1
SDI OUT 2
SDI OUT
SDI OUT 1
SDI OUT 2
e TIME CODE OUT connector
When the time code generator is synchronized to the external
time code signal input on the TIME CODE IN connector, the
external time code is output according to the [TC Out Select]
setting on the Port screen of the web menu.
f NETWORK 1 to 2 connectors
When controlling the unit from a PWS-110PR1, this connects
to a network cable for monitoring the unit by SNMP, configuring
or checking the unit via HTTP, transferring files via FTP, etc.
CAUTION
• For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to these
ports.
Follow the instructions for these ports.
7
Control knob

Advertisement

Table of Contents
loading

  Also See for Sony BPU4800

  Related Manuals for Sony BPU4800