Download  Print this page

Sony 3-0-43-722-11 CFD-V5 Operating Instructions

Cd radio cassette-corder.
Hide thumbs
   

Advertisement

Use TYPE I (normal) tape only.
Utilice sólo cintas TYPE I (normal).
Playing a tape
Reproducción de cintas
1
c
2
To
Do this
Para
adjust the volume
Turn VOLUME.
ajustar el volumen
stop playback
Press xZ.
detener la reproducción
fast-forward or rewind the tape
Press M or m.
avanzar rápidamente o
rebobinar la cinta
pause playback
Press X.
Press the button again to resume play
realizar una pausa
after pause.
eject the cassette
Press xZ.
extraer el cassette
Note
You insert a casette with the side you want to play facing upward.
Nota
Inserte una cinta con la cara que desee reproducir hacia arriba.
Use TYPE I (normal) tape only.
Utilice sólo cintas TYPE I (normal).
Recording
Grabación en una cinta
To record from the CD player
Para grabar desde el reproductor de discos compactos
2
1
c
c
3
c
Para
To
Press
detener la grabación
stop recording
xZ
realizar una pausa
pause recording
X
durante la grabación
Press the button again to resume recording.
Tips
Consejos
• Adjusting the volume or the audio emphasis will not affect the
• El ajuste del volumen o del énfasis de sonido no afectará al nivel de
recording level.
grabación.
• For the best results, use the AC power as a power source for recording.
• Para obtener los mejores resultados de grabación, utilice CA como
fuente de alimentación.
• To erase a recording, proceed as follows:
• Para borrar una grabación, realice lo siguiente:
1 Insert a tape with the recording you want to erase.
2 Set FUNCTION to TAPE•CD/RADIO OFF.
1 Inserte una cinta con la grabación que quiere borrar.
2 Ajuste FUNCTION en TAPE•CD/RADIO OFF.
3 Press z.
3 Presione z.
English only / Sólo inglés
Precautions
On safety
• As the laser beam used in the CD
3
player section is harmful to the
eyes, do not attempt to
disassemble the casing. Refer
servicing to qualified personnel
only.
• Should any solid object or liquid
fall into the player, unplug the
player, and have it checked by
qualified personnel before
operating it any further.
Cleaning the cabinet
• Clean the cabinet, panel and
4
controls with a soft cloth slightly
moistened with a mild detergent
solution. Do not use any type of
abrasive pad, scouring powder, or
solvent, such as alcohol or
benzine.
On power sources
• For AC operation, use the
supplied AC power cord; do not
use any other type.
Realice lo siguiente
• The player is not disconnected
Gire VOLUME.
from the AC power source
(mains) as long as it is connected
Presione xZ.
to the wall outlet, even if the
Presione M o m.
player itself has been turned off.
• Unplug the player from the wall
outlet when it is not to be used for
Presione X.
an extended period of time.
Vuelva a presionar la tecla para reanudar
• For battery operation, use six size
la reproducción después de la pausa.
D (R20) batteries.
Presione xZ.
• When the batteries are not to be
used, remove them to avoid
damage that can be caused by
battery leakage or corrosion.
• The nameplate indicating
operating voltage, power
consumption, etc. is located at the
bottom.
On placement
• Do not leave the player in a
location near heat sources, or in a
To record from the radio
place subject to direct sunlight,
excessive dust or mechanical
Para grabar de la radio
shock.
• Do not place the player on an
2
inclined or unstable place.
• Do not place anything within 10
c
mm of the side of the cabinet. The
ventilation holes must be
unobstructed for the player to
operate properly and prolong the
life of its components.
• If the player is left in a car parked
in the sun, be sure to choose a
3
location in the car where the
player will not be subjected to the
direct rays of the sun.
• Since a strong magnet is used for
the speakers, keep personal credit
cards using magnetic coding or
spring-wound watches away from
the player to prevent possible
damage from the magnet.
Presione
On operation
xZ
• If the player is brought directly
from a cold to a warm location, or
X
is placed in a very damp room,
Vuelva a presionar la tecla
moisture may condense on the
para reanudar la grabación.
lenses inside the CD player
section. Should this occur, the
player will not operate properly.
In this case, remove the CD and
wait about an hour for the
moisture to evaporate.
• If the player has not been used for
a long time, set it in the playback
mode to warm it up for a few
minutes before inserting a
cassette.
Notes on cassettes
• If you are listening to an FM
program near the TV with an
Specifications
• Break off the cassette tab from
indoor antenna, move the player
side A or B to prevent accidental
away from the TV.
recording. If you want to reuse the
tape for recording, cover the
CD Player
AUDIO POWER SPECIFICATIONS
broken tab with adhesive tape.
POWER OUTPUT AND TOTAL
The CD does not play or "00"
HARMONIC DISTORTION
lights in the display even when a
Side A
With 3.2-ohm loads, both channels
CD is in place.
driven from 150 - 10,000 Hz; rated
• Make sure that the CD
1.3 W per channel-minimum RMS
compartment is closed.
power, with no more than 10 % total
• Place the CD with the label
harmonic distortion in AC operation.
Tab for side A
Tab for side B
surface up.
Other Specifications
• The use of a cassette with more
• Clean the CD.
CD player section
than 90 minutes of play time is not
• Take out the CD and leave the CD
recommended except for long,
compartment open for about an
System
hour to dry moisture condensation.
Compact disc digital audio system
continuous recording or playback
Laser diode properties
• Make sure the FUNCTION
Notes on CDs
Material: GaAlAs
selector is set to CD.
Wave length: 780 nm
• Before playing,
The sound drops out.
Emission duration: Continuous
clean the CD with a
Laser output: Less than 44.6 µW
• Reduce the volume.
cleaning cloth. Wipe
(This output is the value measured at a
• Clean the CD, or replace it if the
the CD from the
distance of about 200 mm from the
CD is badly damaged.
center out.
objective lens surface on the optical
pick-up block with 7 mm aperture.)
• Place the player in a location free
• Do not use solvents
Spindle speed
from vibration.
such as benzine,
200 r/min (rpm) to 500 r/min (rpm)
• Clean the lens with a
thinner, commercially available
(CLV)
commercially available blower.
cleaners or anti-static spray
Number of channels
• The sound may drop out or noise
2
intended for vinyl LPs.
Frequency response
may be heard if the CD is recorded
• Do not expose the CD to direct
20 - 20,000 Hz +1/–2 dB
using a personal computer(CD-R,etc.).
sunlight or heat sources such as
Wow and flutter
hot air ducts, nor leave it in a car
Below measurable limit
Tape Player
parked in direct sunlight as there
Radio section
The tape does not move when you
can be a considerable rise in
Frequency range
press an operation button.
temperature inside the car.
FM: 87.6 - 108 MHz
• Do not stick paper or sticker on
• Close the cassette compartment
AM: 530 - 1,710 kHz
securely.
the CD, nor scratch the surface of
Antennas
FM: Telescopic antenna
the CD.
The REC z button does not
AM: Built-in ferrite bar antenna
• After playing, store the CD in its
function or the tape does not play
Cassette-corder section
case.
or record.
• Make sure the safety tab on the
Recording system
If there is a scratch, dirt or
4-track 2 channel stereo
fingerprints on the CD, it may cause
cassette is in place.
Fast winding time
tracking error.
• Make sure the FUNCTION
Approx. 120 s (sec.) with Sony cassette
selector is set to CD, AM or FM.
C-60
Frequency response
If you have any questions or
Poor or distorted playback,
TYPE I (normal): 70 - 10,000 Hz
problems concerning your player,
recording or erasing quality.
General
please consult your nearest Sony
• Clean the heads, pinch roller and
dealer.
capstan with a cleaning swab
Speaker
Full range: 10 cm dia., 3.2 ohms, cone
slightly moistened with cleaning
type (2)
fluid or alcohol.
Outputs
Troubleshooting
• Replace all the batteries with new
Headphones jack (stereo minijack)
ones if they are weak.
For 16 - 68 ohms impedance
• TYPE II (high position) or TYPE
headphones
General
Power requirements
IV (metal) tape is being used. Use
For CD radio cassette-corder:
TYPE I (normal) tape only.
The power does not come on.
120 V AC, 60 Hz
• Demagnetize the heads using a
• Connect the AC power cord
9 V DC, 6 size D (R20) batteries
commercially available tape head
securely.
Power consumption
demagnetizer.
AC 20 W
• Make sure the batteries are
Battery life
inserted correctly.
Record/playback head
For CD radio cassette-corder:
• Replace all the batteries with new
Capstan
FM recording
ones if they are weak.
Sony R20P: approx. 13.5 h
There is no audio.
Sony alkaline LR20: approx. 20 h
• Make sure the FUNCTION
Tape playback
selector is set to the function you
want to operate.
Erase head
Pinch roller
Sony R20P: approx. 7.5 h
• Adjust the volume.
Sony alkaline LR20: approx. 15 h
• Unplug the headphones when
Lens
CD playback
listening through speakers.
Sony R20P: approx. 2.5 h
Noise is heard.
Sony alkaline LR20: approx. 7 h
• Someone is using a portable
Dimensions
telephone or other equipment that
Approx. 420 165 256 mm (w/h/d)
emits radio waves near the player.
(16
5
6
1
8
2
tMove the portable telephone,
projecting parts)
etc., away from the player.
Mass
Approx. 4.1 kg (9 lb. 1 oz) (incl.
Radio
batteries)
Supplied accessory
The audio is weak or has poor
AC power cord (1)
After trying the above remedies, if
quality.
you still have problems, unplug the
• Replace all the batteries with new
Design and specifications are subject to
AC power cord and remove all the
change without notice.
ones if they are weak.
batteries. After all the indications in
• Move the player away from the TV.
the display disappear, plug the
Optional accessories
The picture of your TV becomes
power cord and insert the batteries
Sony MDR headphone series
unstable.
again. If the problem persists, please
consult your nearest Sony dealer.
WARNING
To prevent fire or shock
hazard, do not expose the
player to rain or moisture.
CD Radio
Cassette-
Corder
Operating Instructions
This symbol is intended to
alert the user to the
Manual de instrucciones
presence of uninsulated
"dangerous voltage"
within the product's
enclosure that may be of
sufficient magnitude to
constitute a risk of electric
shock to persons.
This symbol is intended to
alert the user to the
presence of important
operating and maintenance
(servicing) instructions in
the literature
CFD-V5
accompanying the
appliance.
CAUTION
Sony Corporation © 1999
The use of optical instruments with
Printed in China
this product will increase eye
hazard.
3-043-722-11(2)
Choosing Power Sources
Connecting the AC power cord
Using the player on batteries
10
1
inches) (incl.
8
Insert six size D (R20) batteries (not supplied) into the battery compartment.
Notes
• Replace the batteries when the OPR/BATT indicator dims or when the
player stops operating. Replace all the batteries with new ones. Before
you replace the batteries, be sure to take out the CD from the player.
• To use the player on batteries, disconnect the AC power cord from the
player.
WARNING
—Reorient or relocate the
receiving antenna.
Do not install the appliance in a
—Increase the separation between
confined space, such as a bookcase
the equipment and receiver.
or built-in cabinet.
—Connect the equipment into an
outlet on a circuit different from
The FUNCTION selector is located
that to which the receiver is
at the front.
connected.
When you turn on the player, the
—Consult the dealer or an
OPR/BATT indicator lights up.
experienced radio/TV
technician for help.
For customers in Canada
You are cautioned that any
To prevent electric shock, match
changes or modifications not
wide blade of plug to wide slot, fully
expressly approved in this manual
insert.
could void your authority to
operate this equipment.
Information
Owner's Record
For customers in the United States
The model number is located at
This equipment has been tested and
the bottom and the serial number
found to comply with the limits for a
is located in the battery
Class B digital device, pursuant to
compartment.
Part 15 of the FCC Rules. These
Record the serial number in the
limits are designed to provide
space provided below. Refer to
reasonable protection against
them whenever you call upon
harmful interference in a residential
your Sony dealer regarding this
installation. This equipment
product.
generates, uses and can radiate radio
frequency energy and, if not
Model No. CFD-V5
installed and used in accordance
Serial No.
with the instructions, may cause
harmful interference to radio
communications. However, there is
Para español, en este manual de
no guarantee that interference will
instrucciones se describe la forma
not occur in a particular installation.
de empleo del reproductor
If this equipment does cause
solamente.
harmful interference to radio or
television reception, which can be
determined by turning the
equipment off and on, the user is
encouraged to try to correct the
interference by one or more of the
following measures:
Selección de las fuentes de alimentación
Conexión del cable de alimentación de CA
1
to AC IN
a AC IN
2
to a wall outlet
a una toma mural
Utilización del reproductor con pilas
Inserte seis pilas R20 (tamaño D) (no suministradas) en el compartimiento
de pilas.
Notas
• Sustituya todas las pilas por otras nuevas si el indicador OPR/BATT
presenta una luz tenue, o si el reproductor deja de funcionar. Antes de
sustituir las pilas, asegúrese de extraer el disco compacto del
reproductor.
• Para utilizar el reproductor con las pilas, desconecte el cable de
alimentación de CA del mismo.

Advertisement

Table of Contents

   Summary of Contents for Sony 3-0-43-722-11 CFD-V5

  • Page 1 Fast winding time operating voltage, power tracking error. • Make sure the FUNCTION Approx. 120 s (sec.) with Sony cassette consumption, etc. is located at the selector is set to CD, AM or FM. C-60 bottom.
  • Page 2 Location of controls / Ubicación de los controles REC PLAY REW FF STOP/EJECT PAUSE REPEAT RANDOM Tape compartment REPEAT Compartimiento de la cinta CD compartment Compartimiento de CD VOLUME PROGRAM Z PUSH OPEN/CLOSE MEGA BASS* OPR/BATT indicator .,> TUNING Indicador OPR/BATT i (headphone) jack* FUNCTION Para reforzar de los graves, pulse MEGA BASS...

This manual is also suitable for:

Cfd-v5

Comments to this Manuals

Symbols: 0
Latest comments: