Sony Walkman WM-EX562 Operating Instructions

3-860-970-61(1)
Cassette Player
Operating instructions
WM-EX562
WALKMAN is a registered trademark of Sony Corporation.
Sony Corporation © 1998 Printed in Malaysia
For the customers in the USA
Owner's Record
harmful interference to radio or
The model number is located at the front television reception, which can be
and the serial number is located inside determined by turning the equipment off
the tape holder. Record these numbers in and on, the user is encouraged to try to
the space provided below. Refer to them correct the interference by one or more of
whenever you call upon your Sony the following measures:
dealer regarding this product. – Reorient or relocate the receiving
antenna.
Model No. WM-EX562
– Increase the separation between the
Serial No.
equipment and receiver.
– Connect the equipment into an outlet
INFORMATION
on a circuit different from that to which
This equipment has been tested and
the receiver is connected.
found to comply with the limits for a
– Consult the dealer or an experienced
Class B digital device, pursuant to Part
radio/TV technician for help.
15 of the FCC Rules. These limits are
This device complies with Part 15 of the
designed to provide reasonable
FCC Rules. Operation is subject to the
protection against harmful interference
following two conditions: (1) This device
in a residential installation. This
may not cause harmful interference, and
equipment generates, uses, and can
(2) this device must accept any
radiate radio frequency energy and, if
interference received, including
not installed and used in accordance
interference that may cause undesired
with the instructions, may cause harmful
operation.
interference to radio communications.
You are cautioned that any changes or
However, there is no guarantee that
modifications not expressly approved in
interference will not occur in a particular
this manual could void your authority to
installation. If this equipment does cause
operate this equipment.
A
a b
BATT lamp
c
B
2REMOTE
C
HOLD
D
a
OPEN
ϥREPEAT
VOLUME
b
REW
FF ϥREPEAT
p
FF
REW
English
House Current
Welcome!
(see Fig. A-c)
Thank you for purchasing the Sony
Connect the AC power adaptor
WM-EX562 Cassette Player.
AC-E15HG (not supplied) to the
Some features are:
DC IN 1.5V jack and to the wall
• You can enjoy low bass sounds by
outlet. Do not use any other AC
the powerful headphone.
power adaptor.
• You can choose from 2 different
emphasizing tones: MB (MEGA
BASS) and GRV (GROOVE) to
adjust to your favorite sound.
• AMS (Automatic Music Sensor)
function that searches the Specifications for AC-E15HG differ
beginning of the current and 2 depending on the area of purchase.
previous tracks, and succeeding 3 Check your local voltage and the
tracks at high speed. polarity of the plug before
• Repeat Single Track function that purchasing.
enables play of your favorite
single track repeatedly for your
convenience. Connecting the
• AVLS (Automatic Volume Limiter
Headphones/
System) function that moderates
the maximum volume level. Earphones
• Useful remote control.
(see Fig. B)
zGetting Started
1
Preparing a Power
2
Source
Choose the dry battery or house
current as the power source.

Releasing HOLD

Dry Battery (see Fig. A-a)
(see Fig. C)
1 Slide and open the battery
The HOLD function locks the
compartment lid, and insert an
HOLD
Walkman and the remote control
R6 (size AA) dry battery (not
indicator
separately to prevent them from
supplied) by matching the +
operating when you accidentally
and – on the battery to the
press a button. Unlock it before
diagram inside the battery
operating.
HOLD compartment.
1

When to replace the battery

(see Fig. A-b)
Replace the battery with a new one
when the BATT lamp dims.
To lock the Walkman
Battery life (Approx. hours)
Slide HOLD in the direction of the
(EIAJ*)
arrow on the Walkman, or slide
Sony Sony
HOLD on the remote control so
alkaline R6P (SR)
that the HOLD indicator turns
LR6 (SG)
yellow.
Tape playback 29 8
* Measured value by the standard of
EIAJ (Electronic Industries
Association of Japan). (Using a Sony
HF series cassette tape)
Note
ϥREPEAT
• The battery life may shorten
depending on the operation of the
unit.
VOL
For maximum performance we
recommend that you use an alkaline
battery.
Notes
• Do not charge a dry battery.
• When the battery is replaced the
setted functions will be cancelled,
the unit will return to the factory
ϥREPEAT settings.
• When you do not use the Walkman
for a long time, remove the battery
p
to avoid any damage caused by
battery leakage and subsequent
corrosion.
z Operating the
Walkman

Playing a Tape

(see Fig. D-a)
The Auto tape selector
automatically selects the tape
Polarity of
(normal (TYPE I), CrO (TYPE II)
2
the plug
or metal (TYPE IV)) for playback.
1
Insert a cassette.
2
Press ϥREPEAT to start
playing and then adjust the
volume.
When adjusting the volume on
the Walkman
Set the VOL control on the remote
control at maximum.
When adjusting the volume on
the remote control
Set the VOLUME control on the
Walkman to around 6.
Connect the headphones/
earphones to 2REMOTE.
To Press (see
Fig. D-b)
Wear the "L" marked side to
Play the other side ϥREPEAT
the left ear and the "R" marked
during playback
side to the right ear.
Stop playback p
Fast forward FF during stop
Rewind REW during
stop
Repeat the track ϥREPEAT
you are listening to for two seconds
(Repeat Single or more during
Track function) playback
To stop a
single repeat,
press it again.
Find the beginning FF once/
Slide HOLD in the opposite
of the next track/ repeatedly
direction of the arrow on the
succeeding 3 tracks during
(AMS*) playback
Walkman, or slide HOLD on
the remote control.
Find the beginning REW once/
of the current track/ repeatedly
previous 2 tracks during
(AMS) playback
Play the same side REW for two
from the beginning seconds or
(Auto Rewind more during
Play function) stop
Play the other side FF for two
from the beginning seconds or
(Skip Reverse more during
function) stop
* Automatic Music Sensor
Note on Beeps during AMS
operations
• When finding the beginning of the
next 3 tracks during AMS
operations, beeps "• – – –" (beep
followed by three long beeps) are
emitted repeatedly. Likewise, when
finding the beginning of the
previous 2 tracks, beeps "•• – – –"
are emitted repeatedly. While the
remaining tracks are reduced, the
number of long beeps are reduced
accordingly.
Note on AMS, REPEAT Single
Track
• To operate the AMS and the
REPEAT Single Track functions, you
need a blank of 4 seconds or longer
between the tracks. Therefore, if
there is noise between the tracks,
these functions will not detect the
blank and will not operate. Likewise,
if the recording level is moderately
low within a track, these functions
may inaccurately operate.
(turn over)