Related Manuals for ADL soft air simplex wds
Summary of Contents for ADL soft air simplex wds
- Page 1 User Manual soft air ® simplex wds Art. No. 110 470-wds Pressure ulcer prevention and treatment-system Assembly and Operation instructions Health. Security. Independence.
-
Page 2: Table Of Contents
List of contents 1 Foreword Seite 3 2 Safety instructions Seite 4 3 Product overview Seite 4 4 Introduction Seite 5 5 Introduction Seite 5 6 Istallation and setting up the mattress Seite 6 7 Pressure setting Seite 7 8 Static function Seite 8 9 CPR function Seite 8... -
Page 3: Foreword
(Stage 2). With the writing of this user manual the product management of the ADL® GmbH has set itself the goal, to create a good and understandable aid and guidance for the employment of the system. If nevertheless questions remain, please ask your provider for direction and assistance. -
Page 4: Safety Instructions
2 Safety instructions The system may not be used in presence of open flames, heaters a.o’s. Protect the equipment against humidity. Operate it only in dry areas. No combustible gases or liquids may enter into the system. EXPLOSION DANGER! Warning! Note! The compressor is under power, as soon as the power supply plug is put in. -
Page 5: Introduction
4 Introduction soft air® simplex wds is a cover mattress system, meaning there should be an additional mattress on the bed with a thickness of at least 5 cm. This system is suitable for patients with a body weight of Please note that these weight indications are applicable for patients in a lying position. -
Page 6: Istallation And Setting Up The Mattress
6 Installation and setting up the mattress soft air® simplex wds Place the system on the present mattress and fix the straps to this mattress. For this purpose simply tuck the bottom parts underneath the head and foot of the mattress and place it back on the bottom of the bed. Place the mattress in such a way that the tubing of the system is located at the foot of the bed. -
Page 7: Pressure Setting
7 Pressure setting The most effective pressure level can be set manually by turning the knob at the front display of the power unit. Under the deepest point of the patient (normally under the hip) has to be a distance of 3 - 4 cm to the bottom of the overlay system. Check it with your hand. -
Page 8: Static Function
8 Static function In case of a contra indication for alternating pressure according to the indications overview, the large cell mattress can be switched from alternating pressure to static pressure with the wds switch at the power unit. Adjustment to maximum comfort in this mode can be achieved the same way as before. -
Page 9: Cleaning & Servicing Instructions
• Disinfection with cleaning on locations is also possible, when instructions for use and process time are properly kept. ADL® GmbH revisals • prescribes safety-related of all electric powered parts after at least 2 years. -
Page 10: Troubleshooting
11 Troubleshooting Problem Cause Solution Mattress does not inflate Connectors are not accurately Check connection and or inflates insufficiently. locked. Tubes are twisted or position of the tubes. kinked. Defect cell. Exchange possible defect cells. The unit does not operate No power available. -
Page 11: Technical Data
13 Technical data soft air® simplex wds COVER Material Polyurethan Polyvinyl chloride (Mattress) 196 x 88 x 12,5 (Mattress) Dimensions in cm 196 x 88 x 12,5 30 x 12 x 10 (Power unit) ca. 5,6 (Mattress) Weight in kg ca. - Page 12 In case of technical problems please contact your appointed dealer or directly to ADL® GmbH. (Dealer stamp) ADL® GmbH ADL® GmbH An der Germania Brauerei 1 Production- and servicer center 48159 Münster Im Flürchen 1 Germany 99334 Amt Wachsenburg Phone: + 49 251 149896-0...
Need help?
Do you have a question about the soft air simplex wds and is the answer not in the manual?
Questions and answers