Operation - Craftsman PRO Series Operator's Manual
Hide thumbs
Also See for PRO Series:
- Operator's manual (64 pages) ,
- Manual (60 pages) ,
- Operator's manual (68 pages)
Advertisement
Available languages
Available languages
REMOVING DRAWERS
• Empty the drawer.
• Fully extend the drawer.
Left Release Lever
• Push the lever on the right slide down, lift the lever on
the left side up. Pull out drawer to remove.
INSTALLING DRAWERS
Ball bearing slide - Pull slide carriers out on both sides
of unit to fully extended position. Hold the slide on the unit
while aligning it with the slide on drawer. Slightly insert one
side and repeat for the other side. Slowly push drawer to
its fully closed position to engage slide. Open drawer and
reclose to ensure proper operation.
.
n c
, I
i e s
s t r
d u
I n
o o
e r l
a t
W
N
I O
P T
R I
C
S
E
/ D
L S
A I
E T
D
Y
B
U
O
S
S
M I
I A ,
A L
D
E
S
E
T L
T I
Y
B L
M
E
S
S
A
T
N I
U
E
H
S
E :
A T
D
Y
B
N
W
A
R
D
E T
E
H
S
5
1
0
2
6 /
2
3 /
B
M
O
C
L
O
H
G
A L
R I
E
A T
M
L E
G
N
A
D
R
H I
T
-
S
A
H
T
W I
E
C
N
A
D
R
O
C
C
A
I N
D
E
C
U
D
O
R
P
I S
D
N
A
E L
D
O
M
D
A
C
S
K
R
O
W
D
L I
O
S
M
O
R
F
D
E
V
R I
E
D
I S
G
N
W I
A
R
D
S
E
C
T I
C
A
R
P
N
O
T I
A
T
N
E
M
U
C
O
D
D
E
T
A
E L
R
D
N
A
E
T
A
W
F
O
Y
T
R
E
P
O
R
P
Y
R
A
T
E
R I
P
O
R
P
E
H
T
S
S I
N
A I
T
N
O
C
I T
N
O
T I
A
M
R
O
F
N
E I
H
T
D
N
A
G
N
W I
A
R
D
S
H I
T
E
T
A
W
M
O
R
F
N
O
S I
S
M I
R
E
P
N
E
T T
R I
W
T
U
O
H
T
W I
D
E
C
U
D
O
R
P
E
R
E
B
T
O
N
Y
A
M
D
N
A
C .
I N
S ,
E
R I
T
S
U
D
I N
G .
N
R I
E
E
N
G I
N
E
T
C
U
D
O
R
P
C .
I N
S ,
E
R I
S T
U
D
I N
OPERATION
Right Release Lever
E
A T
D
#
O
C
E
V .
E
R
Slide carrier
REMOVING AND INSTALLING SLIDES
• To remove the slide from the unit, first remove the
drawer.
• After removing the drawer check to see if the unit has
rivets located on the front of the slide. To drill out rivets,
use a 5/32-in drill bit. The rivets will need to be replaced
with 5/32-in rivets.
• To reinstall the slide in the appropriate position in the
unit, align front and back lances with mounting holes in
the side of the unit. Pull towards the front of the unit and
downwards until rivet holes in slide line up with holes in
the unit. The rivets will need to be replaced with 5/32-in
rivets.
• For smooth operation, make sure the drawers are
matched with their original slides.
Drill out rivet
OPENING TOP CHEST DRAWERS
TO UNLOCK CHEST
• Unlock unit to open drawers and cover of chest.
TO LOCK CHEST
• Close all drawers and lock.
Note: Cover of chest can be closed if unit is locked.
3
Advertisement
