[Channel %1:] Machine Data %2 [%3] Has Gap In Axis Assignment; [Channel %1:] Machine Data %2[%3] Assigns Axis Not Defined In Channel - Siemens Sinamics S120 Diagnostic Manual

4000 [Channel %1: ] Machine data %2[%3] has gap in axis assignment
Parameters: %1 = Channel number
%2 = String: MD identifier
Definitions: The assignment of a machine axis to a channel by the MD20070 $MC_AXCONF_MACHAX_USED must be contigu-
ous. At system power-up (Power On) gaps are detected and displayed as an alarm.
Reaction: NC not ready.
Mode group not ready, also effective for single axes.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Remedy: Please inform the authorized personnel/service department. The entries for the indices for the machine axes used in
the channels must be contiguous in table MD20070 $MC_AXCONF_MACHAX_USED. Channel axis gaps must be
enabled via MD11640$MN_ENABLE_CHAN_AX_GAP.
Program Switch control OFF - ON.
Continuation:
4002 [Channel %1: ] Machine data %2[%3] assigns an axis not defined in channel
Parameters: %1 = Channel number
%2 = String: MD identifier
%3 = Index: MD array index
Definitions: Only axes that have been activated in the channel by means of MD20070 $MC_AXCONF_MACHAX_USED [kx]=m
may be declared as geometry axes or transformation axes by means of the MD20050
$MC_AXCONF_GEOAX_ASSIGN_TAB [gx]=k. This also applies to MD22420 $MC_FGROUP_DEFAULT_AXES
(gx: Geometry axis index, kx: Channel axis index, k: Channel axis no., m: Machine axis no.).
Assignment of geometry axes to channel axes
MD20050 $MC_AXCONF_GEOAX_ASSIGN_TAB (includes channel axis no. k):
- Geometry axis index: 0, 1st channel: 1, 2nd channel: 1
- Geometry axis index: 1, 1st channel: 2, 2nd channel: 0
- Geometry axis index: 2, 1st channel: 3, 2nd channel: 3
MD20070 $MC_AXCONF_MACHAX_USED (includes machine axis no. m):
- Channel axis index: 0, 1st channel: 1, 2nd channel: 4
- Channel axis index: 1, 1st channel: 2, 2nd channel: 5
- Channel axis index: 2, 1st channel: 3, 2nd channel: 6
- Channel axis index: 3, 1st channel: 7, 2nd channel: 0
- Channel axis index: 4, 1st channel: 8, 2nd channel: 0
- Channel axis index: 5, 1st channel: 0, 2nd channel: 0
- Channel axis index: 6, 1st channel: 0, 2nd channel: 0
- Channel axis index: 7, 1st channel: 0, 2nd channel: 0
Reaction: NC not ready.
Mode group not ready, also effective for single axes.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Remedy: Please inform the authorized personnel/service department.
Correct
- MD20050 $MC_AXCONF_GEOAX_ASSIGN_TAB
- MD24... $MC_TRAFO_AXES_IN_...
- MD24... $MC_TRAFO_GEOAX_ASSIGN_TAB_...
- MD22420 $MC_FGROUP_DEFAULT_AXES
- and/or MD20070 $MC_AXCONF_MACHAX_USED.
Program Switch control OFF - ON.
Continuation:
Alarms
Diagnostics Manual, 07/2010, 6FC5398-8BP40-0BA0
NCK alarms
19