Download  Print this page

Options; Modifiers - Kenmore Sensor Smart Use And Care Manual

Hide thumbs

Advertisement

Table of Contents
Custom Program
Use the Custom Program to select the Cycle, Options and
Modifiers you use most frequently and store it for future use.
To store a cycle for future use
1. Select a Cycle.
2. Select the desired Options.
3. Select the desired Modifiers.
4. Press and hold Custom Program for 3 seconds until you hear
a beep.
5. Press Start.
To reuse this cycle
1. Press Custom Program.
2. Press Start.

Options

You can customize your cycles by selecting options.
Damp Dry Signal
Select the Damp Dry signal to alert you that your clothes are
approximately 80% dry. This is useful when you want to remove
lightweight items in a mixed load to prevent over drying, or
remove partially dry items that may need ironing.
NOTE: The Damp Dry Signal is an option that is only available
with Automatic cycle.
Wrinkle Guard
®
III
Wrinkle Guard III prevents wrinkles that form when you cannot
unload the dryer promptly at the end of a cycle.
Press Wrinkle Guard III to get up to 2 ¹⁄₂ hours of heat-free,
periodic, tumbling at the end of a cycle.
Stop Wrinkle Guard III at any time by pressing the Wrinkle
Guard III pad or opening the dryer door.
For the DELICATE/CASUAL Auto Dry cycle, Wrinkle Guard III
is preset to ON. The other Auto Dry cycles will retain the
Wrinkle Guard III setting. (For example, if you select Wrinkle
Guard III in the NORMAL cycle, Wrinkle Guard III will be ON
the next time you select the NORMAL cycle).
NOTE: If you do not select Wrinkle Guard III, the dryer stops after
Cool Down.
18
Touch Up
Select this option to remove wrinkles from clean items such as
clothes packed in a suitcase or items wrinkled from being left in
the dryer too long.
Press TOUCH UP once to get HEAVY DUTY (30 minutes of
high heat). Use Heavy Duty for medium to heavy weight items
such as bedspreads and jeans.
Press TOUCH UP twice to get DELICATE (20 minutes of low
heat). Use Delicate for light to medium weight items such as
blouses and skirts.
Press MORE TIME or LESS TIME to adjust the cycle time.
The Wrinkle Guard III option is also available in TOUCH UP .
Remove clothes immediately when tumbling stops.

Modifiers

When you select a cycle, the preset Auto Dry Level (Auto Dry) or
Timed Dry settings for that cycle will glow. Modifiers allow you to
change the preset settings and further customize your cycles.
Auto Dry Level with Ultra Moisture Sensing
Auto Dry Level with Ultra Moisture Sensing provides the most
accurate drying results in the shortest time. This can help you
save money on utility bills and reduce the risk of fabric damage.
Dryness level is determined by dual sensor strips that measure
the moisture in your clothes. Once the desired dryness level is
reached, the electronic sensors signal the dryer to stop to
prevent overdrying your clothes.
For all Auto Dry cycles, the Auto Dry Level is automatically set at
Normal. This setting provides the recommended fabric care for
your cycle. the display will show the estimated time (in minutes)
required to reach an approximate 80% dry level. After the 80%
dryness level is reached, the remaining drying time required will
be displayed as actual time remaining.
Use the Normal setting to dry most loads. At the end of the cycle,
feel the dried clothes.
If they are damper than you like, select a setting above
Normal the next time you dry a similar load.
If they are drier than you like, select a setting below Normal
the next time you dry a similar load.
To change the dryness level
Press AUTO DRY LEVEL until the desired dryness level glows.
NOTE: Auto Dry Level is not a selectable option with the
EXPRESS DRY™ cycle, the AIR DRY cycle or TOUCH UP .
To change from estimated to actual drying time
Press MORE TIME or LESS TIME until the desired time is
displayed. The light for Timed Dry (Actual) will glow.

Advertisement

Table of Contents
loading