Related Manuals for TrackSnap TrackSnap TS-DSC-S40-01
No related manuals
Summary of Contents for TrackSnap TrackSnap TS-DSC-S40-01
Page 1
Document Author: Paul Skelly Version: TS S40.01 Issue Date: 16/04/2006 Status: Released Document Location: http://www.tracksnap.com www.tracksnap.com TrackSnap Manual Sony DSC-S40 Model TS-DSC-S40-01 TrackSnap is a product range of Comit Services P/L...
Page 2
TrackSnap Manual Congratulations on the purchase of a new TrackSnap camera system. This manual provides detailed information for the setup and use of your system. Please read this manual before using your TrackSnap camera. The information provided will give you good service from your system.
Page 3
Model TS-DSC-S40-01 TrackSnap Manual All TrackSnap cameras use a PixController PIR motion detection sensor. PIR stands for Pryoelectric Infra- Red, which detects warm targets in motion over ambient background temperature. A stationary target or a target not moving can not be detected. The target must also have a warmer surface temperature than the ambient background temperature in order to be detected.
Page 4
TrackSnap Manual When turning power on to your TrackSnap both the red and green LED will light up. They will both stay on for 30 seconds. This time will allow the PIR circuit to warm up. After this time expires the green LED will turn off and the red LED will blink 5 times letting you know that the board is entering a 1 minute automatic walk- test phase.
Page 5
All switches Down (Off) except SW6 and SW10 Up (ON) and a summary is listed: 10 Sec PIR Delay 24 hour mode of operation Sony S40 Camera Continuous movement movie setting Green PIR LED ON Switches 1 and 2 control the delay between PIR events. This setting is used so you can limit or not limit the number of photos taken when a motion event triggers your board.
Page 6
RSP (on/off digital camera mode using external supply) RSP3i (on/off mode, internal supply, D370/D380) RSP4i (on/off mode, internal supply, D390/D395) Camera (LE II) Sony/Canon LANC Camcorder in VTR mode - Sony/Canon LANC Camcorder in Photo mode - Sony DSC-S40/DSC-S600 Samsung A402 Olympus D-425 Digital Concepts 2.1 (DC 2.1)
Page 7
TrackSnap Manual Switches 8 and 9 sets up the recording time for your LANC camcorder. Recording Time 30 Seconds - Continuous recording as long as motion is present. 1 Minute 2.5 Minutes 5 Minutes Switches 10 controls the green PIR LED.
Page 8
Low battery level detection - the green PIR LED will blink when a low battery is detected. 10-Postion DIP switch so you can easily configure board settings. Tiny board size. Fit a Sony DSC-P41 into a Pelican 1060 case with room to spare. PIR sensitivity POT to adjust the PIR detection range.
Page 9
Model TS-DSC-S40-01 TrackSnap Manual Version Page 9 of 12 Released TS S40.01 This document comprises information provided by Suppliers and is assumed to be correct.
Page 10
Model TS-DSC-S40-01 TrackSnap Manual The PIR lens is mounted in the Pelican 1060 case with your board. The lens is centred over the PIR Sensor and be 16.5 mm from the top. We mount the lens with the “ridges” facing towards the PIR sensor. Do not scratch the lens on either side.
Page 11
Version TS S40.01 This document comprises information provided by Suppliers and is For fastest shutter times set your Sony DSC-S40 camera setting up as: Leave the camera on -program- setting • Exposure Value(EV) set to • Focus set to Multi AF •...
Page 12
When I use the PixController Be sure to setup your Sony Camera into Movie DIP Switch setting for “Movie taking mode. Mode” I still get still photos. What am I doing wrong?