Sony POWER HD FX PDW-700 Operation Manual page 59

to change the color temperature automatically
when the ND filter is switched.
1
Display the WHITE FILTER page of
the MAINTENANCE menu.
M15 WHITE FILTER
ND FILTER CTEMP :
ND FLT CTEMP <1>:
ND FLT CTEMP 2-4:
ELECTRICAL CC<A>:
ELECTRICAL CC<B>:
ELECTRICAL CC<C>:
ELECTRICAL CC<D>:
For details on menu operations, see "Basic
menu operations" on page 163
2
Select ND FILTER CTEMP, and turn
the MENU knob to display "ON".
3
To assign an electrical CC filter to
FILTER selector position number 1,
select "ND FLT CTEMP <1>". To
assign it to positions 2 to 4, select "ND
FLT CTEMP 2-4".
4
Turn the MENU knob to display the
desired color temperature.
As you turn the MENU knob, the color
temperature changes as follows: 3200K y
4300K y 5600K y 6300K.
5
Repeat steps 3 and 4 as required.
To switch between electrical CC filters
with an ASSIGN switch
You can assign the function that switches
between electrical CC filters to an ASSIGN
switch. This allows you to switch between color
temperatures (3200K/4300K/5600K/6300K) that
have been assigned to up to four positions (A to
D) with each press of the ASSIGN switch.
Regardless of assignments to ASSIGN switches,
you can also switch between the color
temperatures assigned to each position from a
1)
remote control unit.
1) When the RM-B150/B750, MSU-900/950, or RCP-
750/751/920/921 is connected.
1
Display the WHITE FILTER page of
the MAINTENANCE menu.
For details on menu operations, see "Basic
menu operations" on page 163.
2
TOP
OFF
3200K
5600K
3200K
4300K
5600K
6300K
3
4
White balance memory
Values stored in memory are held until the white
balance is next adjusted.
There are two sets of white balance memories, A
and B, and adjustments for each of the ND filters
can be automatically stored in the memory
corresponding to the setting (A or B) of the
WHITE BAL switch. The camcorder has four
built-in ND filters, so a total of eight (4 × 2)
adjustments can be stored. However, the memory
contents are not linked to the ND filter settings in
the following cases.
• When the number of memories allocated to
each of A and B is limited to one by setting the
FILTER WHT MEM item on the WHITE
SETTING page of the OPERATION menu to
OFF.
• When the electrical CC filter switching function
has been assigned to an ASSIGN switch, or
when a remote control unit has been connected.
(In these cases, the contents of white balance
memory are linked to electrical CC filter
positions (A to D).)
If the WHITE BAL switch is set to B, and on the
WHITE SETTING page of the OPERATION
Adjusting the Black Balance and the White Balance
Select the position to which to assign a
CC filter by selecting one of
"ELECTRICAL CC<A>" to
"ELECTRICAL CC <D>", and then
turn the MENU knob to select the
desired color temperature.
As you turn the MENU knob, the color
temperature changes as follows: 3200K y
4300K y 5600K y 6300K.
To set no color temperature
Select "-----" with ELECTRICAL CC<C> or
<D> selected.
When the ASSIGN switch is pressed, the
setting for that position is not displayed. For
example, if "-----" is set for one position, then
switching between the remaining three
positions is carried out.
Repeat step 2 as required.
Assign the electrical CC filter switching
function (ELECTRICAL CC) to an
ASSIGN 1/3/4 switch, the COLOR
TEMP button, or the RET button on the
lens (see page 178).
59