Operation/Error Messages - Sony PDW-510P Operation Manual

Alarm Indicators on color/
Message monochrome LCDs
Warning/ Flashing/
Battery continuous
status
indication
ACC – –
Sensor!
Skew!
Sensor
1) Asterisks (*) are replaced by digits in the display.
2) During recording
3) During playback, fast forward, fast reverse, or stop
4) 1 flash/second
5) 4 flashes/second

Operation/error messages

An operation or error message is displayed in the
operation/error message display area (see page 121) in the
viewfinder.
Operation/error Meaning
message
AUTO INTERVAL Indicates the camera is in the Auto
**M**S Interval Rec mode. **M**S indicates
the shooting interval.
MANU INTERVAL Indicates the camera is in the single
*FRAME shot mode of the Manual Interval Rec
mode. *FRAME indicates the number
of frames.
INTERVAL **S(M/ Indicates the camera is in the
H)*FRAME consecutive mode of the Manual
Interval Rec mode. **S(M/H) indicates
the trigger interval and *FRAME
indicates the number of frames.
LOW LIGHT Appears, depending on the setting, to
indicate the subject illumination is
inadequate.
ON-BOARD Appears when the backup battery for
BATTERY EMPTY
the internal clock has been used up.
HIGH Indicates that temperatures have risen
TEMPERATURE inside the unit. Avoid continued use in
this state.
1) To replace the backup battery, contact your nearest Sony dealer.
A message for DVR operation is displayed in the setting
change and adjustment progress message display area in
the viewfinder (see page 124).
Message Meaning and action to take
ILL. Disc! The disc cannot be used by this unit. Insert
another Professional Disc.
ILL. Index! Index file or file system error. Exchange or
No FS! format the disc.
Unknown FS!
Indicators in viewfinder/
on camcorder body
:Continuous :1 flash/s
:4 flashes/s
WARNING REC/tally BATT
–
1)
Warning Problem VDR
sounds operation
:
4 beeps/s
:
1 beep/s
:
Continuou
s beep
Internal Operation
drive continues.
sensor
error
6) During recording pause
7) During recording or pause
8) During recording, displayed in color LCD only (when the DISP SEL
switch is set to STATUS)
Message Meaning and action to take
No Support! A recorded clip cannot be handled by this
unit. Exchange or format the disc.
FORMAT NG! The disc cannot be used by this unit.
Exchange the disc.
Disc Damage The disc cannot be recorded. To record,
exchange the disc.
Non AV Full The disc is full. Exchange or format the
MAX # Files disc.
DI read err The disc was not recognized. Try ejecting
Read err the disc and inserting it again. Or
DRV ADJ err exchange the disc.
Run Salvage Salvage processing needs to be done on
the disc. To record on the disc, eject the
disc, insert it again, and execute salvage
processing.
Salvage NG Salvage processing failed. For details, see
3-1-6 "Handling of Discs When Recording
Does Not End Normally (Salvage
Function)" (page 38).
REC INHI.! The Write Inhibit tab of the disc is in the
recording disabled position, or salvage
processing needs to be done on the
loaded disc. Set the tab to the recording
enabled position. Or eject the disc, insert it
again, and perform salvage processing.
1) The loaded disc has a different recording
IMX** Clip
format. Exchange the disc, or change the
DVCAM Clip
recording format.
4CH/24 Clip
8CH/16 Clip
Index File! There is an unsupported index file on the
disc to which you are trying to record.
Exchange or format the disc.
File System There is an unsupported file system on the
disc to which you are trying to record.
Exchange or format the disc.
Action to take
Protect the unit from
shock and vibrations,
turn off the power,
and contact a Sony
service
representative.
175
10-3 Operation Warnings