System Menu - Sony HD 3CCD COLOR BRC-H700 Operating Instructions Manual
Hd 3ccd color video camera
Hide thumbs
Also See for HD 3CCD COLOR BRC-H700:
- System manual (66 pages) ,
- Manual (55 pages) ,
- Command list (26 pages)
Table of Contents
Advertisement
SYSTEM Menu
< S Y S T E M >
> I R - R E C E I V E
O N
I M G - F L I P
O F F
P A N R E V E R S E
O F F
T I L T R E V E R S E
O F F
D I S P L A Y I N F O
O F F
A N A L O G O U T
Y P
P
B
R
S Y N C T Y P E
S Y N C
S Y N C M A S T E R
S T D
IR-RECEIVE (infrared signal reception)
When it is set to OFF, the camera does not receive the
signal from the supplied Remote Commander.
Be sure to keep it ON when you use the supplied Remote
Commander.
Note
You cannot set IR-RECEIVE to OFF when you operate
the menu using the supplied Remote Commander. To
set it to OFF, use the RM-BR300 Remote Control Unit
(not supplied) or the VISCA command.
IMG-FLIP (image flip)
Set IMG-FLIP to ON to rotate the camera image
supplied from the RGB/COMPONENT connector
upside down and to reverse the direction of the camera
movement by pan/tilt operation.
Set PAN REVERSE to ON to reverse the horizontal
movement of the camera image.
Set TILT REVERSE to ON to reverse the vertical
movement of the camera image.
When you set IMG-FLIP to ON, “Please restart
system!” appears. Turn off the power of the camera and
turn it on again.
Note
• Regardless of the IMG-FLIP ON/OFF setting, images
shot by the camera are accumulated for the vertical
synchronization period and output from the RGB/
COMPONENT connector of the camera and the
connector on the optional interface board inserted into
the card slot.
• When you set IMG-FLIP to ON, then turn off the
camera and turn it on again, PAN REVERSE and
TILT REVERSE will be set to ON. When you set
IMG-FLIP to OFF, then turn the power off and on
again, PAN REVERSE and TILT REVERSE will be
set to OFF.
DISPLAY INFO (information display)
When the camera settings are stored in POSITION 1 to
16 using the supplied Remote Commander or the RM-
BR300 Remote Control Unit, the message “PRESET
No. xx” automatically appears for 2 seconds on the
monitor screen. If you want to display the message each
time the camera is operated, set DISPLAY INFO to ON.
Set it to OFF to cancel the display.
Notes
• If the built-in cooling fan of the camera has
accidentally stopped, a certain message appears in the
image signal of the interface board inserted in the
RGB/COMPONENT terminal and the card slot in this
camera. The message is displayed when DISPLAY
INFO is set to ON, and is not displayed when it is set
to OFF. The display setting of the message is active in
the transmission from the optional BRU-H700.
Whether DISPLAY INFO is ON or OFF, the tally
lamp on the top of the camera flashes at approximately
0.5-second intervals.
• If the DATA MIX switches on the rear of the camera
and in the optional BRU-H700 are set to OFF, the
caution about the fan is not displayed in the interface
board output inserted in the card slot in the camera or
BRU-H700. In this case, the menu is not displayed,
either.
ANALOG OUT
Select the signal output from the RGB/COMPONENT
connector on the camera. Select YPbPr for component
signal output, or RGB for RGB signal output.
When RGB is selected with ANALOG OUT, ADD
SYNC appears. If you set ADD SYNC to RGB, a sync
signal is added to each R, G and B signal. If you set it to
OFF, no sync signal is added.
SYNC TYPE appears when either YPbPr or RGB is
selected with ANALOG OUT, and you can select the
type of sync signal,
SYNC for tri-level sync or VD for
bi-level sync.
SYNC MASTER
When you connect a sync signal generator, you can
select an output video signal that is synchronized with
the external video sync signal input to the EXT SYNC
IN connector on the camera from the generator.
STD: The output video signal from the RGB/
COMPONENT connector on the camera is
synchronized with the external video sync signal.
HD1: The output signal from the HFBK-HD1 HD
Interface Board inserted into the camera is
synchronized with the external sync signal.
SD1: The output signal from the HFBK-SD1 SD
Interface Board inserted into the camera is
synchronized with the external sync signal.
Note
This menu item is available when the HFBK-HD1 or
HFBK-SD1 Interface Board is inserted into the BRU-
H700 HD Optical Multiplex Unit.
Page 35
SYSTEM Menu
Advertisement
Table of Contents
