Mitsubishi Electric AE-200A Instruction Book page 21

Object
Trend Log Group
Apportioned Electric
Energy
Trend Log
Interlocked Units
Apportioned Electric
Energy
Trend Log
PIcontroller Electric
Energy 1–4
Trend Log Pulse
Input Electric Energy
1–4
Trend Log Group
Apportionment
Parameter
Trend Log
Interlocked Units
Apportionment
Parameter
*1 "Dry" can be used only when the "Use Dry Mode" setting is enabled (checked) on the BACnet
disabled (unchecked).)
*2 "Charge" license is required for AE-200/AE-50/EW-50.
*3 When the "Operational Mode State" received from the indoor unit is "Auto Cool", "Cool" can be selected; when it is "Auto Heat", "Heat"
can be selected, or "Auto" can be selected for both.
*4 "Use Fan Speed Mid1/Mid2" setting of the BACnet
Processing Unit fan speed switching steps are shown in the table below. (The default setting of "Use Fan Speed Mid1/Mid2" of the
®
BACnet Setting Tool is disabled (unchecked).)
(In the automatic wind velocity compatible model, "Auto" is valid in addition to the fan speed in this table.)
Unit type
Indoor unit
LOSSNAY and OA
Processing Unit
*5 Low < Mid 2 < Mid 1 < High
*6 mm: PI controller address (01–50)
*7 Can be used only for the interlocked units.
aa: Interlocked unit address (01–50)
*8 When the air direction received from the indoor unit is "Downblow 20%" or "Auto", "Horizontal" will be output to BACnet
*9 The value of the "Present_Value" in the "Room Temp" (AI_01xx09) object is logged in as the log record.
*10 Batch commands are made for the "System Forced Off" instance number (019921) for all groups.
*11 When the "System Forced Off" (individual/collective) from BACnet
AE-200/AE-50/EW-50 to "ON/OFF (Level signal)". "External Input Setting" can be configured on the Initial Setting Tool, Web Browser for
Initial Settings, or AE-200/AE-50's LCD. (Refer to the AE-200/AE-50/EW-50 Instruction Book (Initial Settings) for settings methods.)
*12 Electric energy for the electricity meter connected to the Pulse Input (PI) of AE-50/EW-50
*13 Electric energy 1 to 4 correspond to signal lines Ch1 to 4 on the PI controller or metering devices 1 to 4 connected to Pulse Input (PI) of
AE-50/EW-50.
WT07919X04
Object Instance
Inactive(0)
type number
LOG 01xx83
LOG 61aa83
LOG 41mm84–87
LOG 410084–87
LOG 01xx88
LOG 61aa88
®
"Use Fan Speed Mid1/Mid2" setting
Enabled
Disabled
Enabled
Disabled
Units
Active(1)
*23
Text-1(1) *23 Text-2(2)
Setting Tool, and effective fan speeds from indoor unit, LOSSNAY, and OA
Number of available
fan speeds
2
3
4
2–4
1
2
3
4
1
2–4
®
communication is used, do not set the "External Input Setting" for
21
Text-3(3) Text-4(4) Text-5(5)
®
Setting Tool. (The default setting is
Available fan speed
Low Mid 2 Mid 1
V
V V
V V V
V
V
V V
V V V
V
Remarks
*2 *24
*2 *7 *24
*2 *6 *13
*15 *16 *17
*18 *24
*2 *13 *15
*16 *17
*18 *24
*2 *24
*2 *7 *24
V: Available
High
V
V
V
V
V
V
V
V
V
V
®
.