Snapper ICFR7005BV, CICFR5505HV Safety Instructions & Operator's Manual
  1. Manuals
  2. Brands
  3. Snapper Manuals
  4. Tiller
  5. CICFR5505HV
  6. Safety instructions & operator's manual

Snapper ICFR7005BV, CICFR5505HV Safety Instructions & Operator's Manual

Intermediate rear tine tiller series 5
Hide thumbs Also See for ICFR7005BV, CICFR5505HV:
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL DESIGNATION
REAR TINE MODEL
C – Commercial Model
I – Intermediate Size Model
C – Counter Rotating Tines
F – Forward Rotating Tines
R – Rear Tine Type Model
Thank you for buying a SNAPPER Product! Before operating your TILLER, read this manual carefully and pay
particular attention to the "IMPORTANT SAFETY INSTRUCTIONS" on Page 2.
equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in
accordance with the operating instructions and common sense!
COPYRIGHT © 2002
SNAPPER INC.
ALL RIGHTS RESERVED
Safety Instructions & Operator's Manual for
MODEL NUMBER EXPLANATION
I
C
55 – 5.5 HP (Horse Power)
REAR TINE TILLER
F
R
55
5 - Series Designation
INTERMEDIATE
SERIES 5
MODEL
ICFR5505BV
CICFR5505HV
05
BV
ENGINE MODEL
SERIES DESIGNATION
B – Briggs Engine
H – Honda Engine
V–Over Head Valve
Remember that all power
MANUAL No. 7-4753 (Rev. 1, 3/8/02)
ENGINE HP

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ICFR7005BV, CICFR5505HV and is the answer not in the manual?

Questions and answers

Related Manuals for Snapper ICFR7005BV, CICFR5505HV

Summary of Contents for Snapper ICFR7005BV, CICFR5505HV

  • Page 1 F – Forward Rotating Tines R – Rear Tine Type Model Thank you for buying a SNAPPER Product! Before operating your TILLER, read this manual carefully and pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Page 2. equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with the operating instructions and common sense! COPYRIGHT ©...

  • Page 2: Important Safety Instructions

    If you have any questions pertaining to your tiller which your dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER, McDonough, Georgia, 30253. Phone: (1-800-935-2967).

  • Page 3: Table Of Contents

    ! IMPORTANT ! The pictures and illustrations in this manual are provided for reference only and may differ from your specific model. Contact your local SNAPPER dealer if you have questions.

  • Page 4: Section 1 - Familiarization

    1.1 INTRODUCTION: This manual covers the recommended operating procedure and routine service requirements on SNAPPER Intermediate Rear Tine Tiller. It is recommended that all operators of this Tiller become thoroughly familiar with the controls and proper operation of the unit before operating. Specific details involving the engine are found in the separate engine owner’s manual.

  • Page 5: Section 2 - Operating Instructions

    2.1 BEFORE OPERATING: Be thoroughly familiar with the operation of ALL controls and how to use them BEFORE operating your Tiller. Transmission shifting is done by shifting the WHEEL and TINE SHIFT LEVER into the desired position. See Figure 3.

  • Page 6: Starting & Stopping

    Section 2 - OPERATING INSTRUCTIONS STARTING – STOPPING FIGURE 4 2.4 ENGINE STARTING PROCEDURE Step 1: Place the WHEEL and TINE SHIFT LEVER in the NEUTRAL position and make sure the WHEEL and TINE CONTROL BAIL is in the released position. Step 2: Briggs Engine - For cold starts, move the CHOKE CONTROL on the engine forward into CHOKE position.

  • Page 7: Handlebar Adjustment

    MOVE FUEL VALVE TO ON POSITION FIGURE 6A Step 4: Move to the right side of Tiller and place your foot on top of the right wheel (See starting procedure decal located on top of the tine cover), hold handle bar, then pull the ROPE STARTER HANDLE in smooth, steady motion until the engine starts.

  • Page 8: Section 2 - Operating Instructions

    Section 2 - OPERATING INSTRUCTIONS 2.6 TRANSPORTING 2.6.1 FORWARD/REVERSE: To transport the Tiller to a new tilling site using its own power, raise the tines to clear lawn and paved surfaces to prevent gouging. Release the WHEEL and TINE CONTROL BAIL and lift the rear of the Tiller to take...

  • Page 9: Section 3 - Adjustments & Repair

    To retain the original quality of your Tiller, use only genuine SNAPPER replacement parts. Specify the model and serial number as found on the nameplate of your Tiller when contacting your SNAPPER Dealer for parts or service assistance. 3.2 STANDING THE TILLER ON END...

  • Page 10: Tiller Tines

    Section 3 - ADJUSTMENTS & REPAIR 3.4 TILLER TINES Your Snapper Tiller has right hand and left hand tines. Replace both tines if blades become bent or are badly worn or otherwise damaged. Use correct Snapper replacement tines. The tines are secured to the tine shaft with a shear bolt, Part No.

  • Page 11: Off Season Storage

    STEP 1: Drain gasoline from fuel system and drain the engine crankcase oil (refer to engine manual for details). STEP 2: After standing the Tiller on end, check the plugs in the chain case for leakage. After extended period, some grease may seep through upper bearing races.

  • Page 12: Warranty

    For three (3) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.

  • Page 13: Primary Maintenance

    PRIMARY MAINTENANCE...
  • Page 14 PRIMARY MAINTENANCE...
  • Page 15 PRIMARY MAINTENANCE...

  • Page 16: Primary Maintenance

    PRIMARY MAINTENANCE...

  • Page 17: Product Registration Form

    Date of Purchase ___________________________________________________________ Retailer ___________________________________________________________________ Retailer’s Phone Number____________________________________________________ It is very important that you register your purchase with Snapper to ensure warranty coverage. Please mail your product registration card to: Snapper at P.O. Box 777, McDonough, Georgia 30253. Or you may register on line at www.snapper.com.
  • Page 18 Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA.

This manual is also suitable for:

Icfr5505bv

Table of Contents