Advertisement
Quick Links
Installation
Instructions
11
1
10
9
Figure 1. Contents
This kit is to install a clean-out tool on a variety of
snowthrowers.
WARNING
Before beginning any service work turn off
ignition, and disconnect the spark plug wire.
GENERAL OPERATION
After installation of the clean-out tool kit, make sure
clean-out tool is attached to handle on machine. Do not
operate the machine without the clean-out tool properly
stored on the handle.
Upon completion of installation of clean-out tool, keep
these instructions and warnings with the Operator's
Manual.
Note: For proper use of clean-out tool it may be neces-
sary on some models to remove the wire guard from the
chute.
3
5
4
7
6
8
12
2
1
Clean-Out Tool Kit
319 / 520 / 551 Single Stage, 5-13 HP
Intermediate or Large Frame Snowthrowers
Kit Contents:
Ref. Part No.
Qty.
Description
1
1733209
1
CLEAN-OUT TOOL
2
1726727
1
BRACKET, Lower
3
1726728
1
CLIP
4
1726995
1
SPACER, 1-1/4" Long
5
1678392
1
SPACER, 11/32" Long
6
1960727
1
SCREW, Slotted, 10-24 x 2-1/2
7
1960589
1
SCREW, Phillips Head, 10-24 x 3/4
8
1933896
1
NUT, Nylock, 10-24
9
1960729
1
CAPSCREW, 5/16-18 x 1
10
1960730
1
CAPSCREW, 5/16-18 x 2
11
7071880
1
DECAL, Danger
12
1931338
1
Carriage Bolt, 5/16-18 x 1-3/4
CLEARING A CLOGGED DISCHARGE
CHUTE
Hand contact with the rotating impeller inside the dis-
charge chute is the most common cause of injury associ-
ated with snowthrowers. Never use your hand to clean
out the discharge chute.
To clear the chute:
1. SHUT OFF THE ENGINE.
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean out tool, not your hands.
DANGER
Do not clean out discharge chute with hands.
Contact with moving parts inside chute will
cause serious injury. Use clean out tool provided
with machine. Use the following procedure to
remove objects or clear the chute:
1. Stop the engine. Remove the key
2. Wait 10 seconds to be sure the auger/impeller
blades have stopped rotating.
3. Always use the clean-out tool. DO NOT use your
hands.
Part No. 1687099
Advertisement
Related Manuals for Simplicity 1687099
Summary of Contents for Simplicity 1687099
-
Page 1: General Operation
2. Wait 10 seconds to be sure the auger/impeller blades have stopped rotating. 3. Always use the clean-out tool. DO NOT use your hands. Clean-Out Tool Kit Part No. 1687099 319 / 520 / 551 Single Stage, 5-13 HP Intermediate or Large Frame Snowthrowers Qty. Description... - Page 2 Installation Instructions Figure 2. A. Existing Danger Decal C. New Danger Decal B. Discharge Chute INSTALLATION Decal Installation 1. Clean and dry existing danger decal (A, Figure 2) and surrounding area. 2. Apply new decal (C) by removing the backing from decal and placing directly over existing decal (A) aligning top edges of both decals.
- Page 3 Clean-Out Tool Kit (TUBE HANDLE MODELS) 1. Remove existing hardware (A, Figure 5) from upper hole on left side handle (C) as shown. Discard cap- screw (D). 2. Using square hole install lower bracket (B) into upper hole on left side handle (C) as shown. Secure with new 5/16-18 x 2 capscrew (D) and nut (A).
- Page 4 Installation Instructions Figure 7. Mounting Lower Bracket (520) A. Wing Lock Knob D. Handle, LH B. Lower Bracket E. Carriage Bolt, C. Screw, Curved Head (520 MODELS) 1. Remove wing lock knob (A, Figure 7) and carriage bolt (E) or screw (C) from hole on left side handle (D) as shown.