Table of Contents
Advertisement
Quick Links
MODEL DESIGNATION
SELF-PROPELLED
CUTTING WIDTH
E – European Model
L
Aluminum Deck Model
-
P – Self Propelled Model
21 – 21" Cutting Width
50 - 5.0 HP (Engine Horse Power)
Thank you for buying a SNAPPER Product! Before operating your Walk Behind, read this manual carefully and pay
particular attention to the "IMPORTANT SAFETY INSTRUCTIONS" on Pages 2 & 3. Remember that all power
equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance
with the operating instructions and common sense!
COPYRIGHT © 2000
SNAPPER INC.
ALL RIGHTS RESERVED
Safety Instructions & Operator's Manual for
21" CAST ALUMINUM DECK
MODEL NUMBER EXPLANATION
E
L
P
WALK MOWERS
21
60
2
60 – 6.0 HP (Engine Horse Power)
2 - Series Designation
E – Electric Start Model
KW - Kawasaki Engine
V - Over Head Valve Engine
EUROPEAN
SERIES 2
SELF-PROPELLED &
ELECTRIC START
MODELS
ELP21502KWV
ELP21602
ELP21602E
E
ENGINE OPTIONS
SERIES DESIGNATION
ENGINE HORSE POWER
MANUAL No. 7-3709 (I.R. 4/28/00)
Advertisement
Table of Contents
Related Manuals for Snapper ELP21502KWV, ELP21602, ELP21602E
Summary of Contents for Snapper ELP21502KWV, ELP21602, ELP21602E
- Page 1 50 - 5.0 HP (Engine Horse Power) Thank you for buying a SNAPPER Product! Before operating your Walk Behind, read this manual carefully and pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3. Remember that all power equipment can be dangerous if used improperly.
-
Page 2: Important Safety Instructions
If you have any questions pertaining to your machine which your dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER, McDonough, Georgia 30253. Phone: (1-800-935-2967). -
Page 3: Important Safety Instructions
11. Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices. 12. Use only genuine SNAPPER replacement parts maintained. -
Page 4: Table Of Contents
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS... 2-3 TABLE OF CONTENTS ... 4 SECTION 1 - FAMILIARIZATION... 5 SECTION 2 - OPERATING INSTRUCTIONS... 6-8 Pre-start Checklist ... 6 Starting & Stopping Engine & Blades... 6-7 Starting & Stopping Wheel Drive ... 7 Handle Height Adjustment ... -
Page 5: Section 1 - Familiarization
DISCHARGE DOOR FIGURE 1.1 1.2 NOMENCLATURE The nomenclature information above, Figure 1.1, shows the essential parts of the SNAPPER WALK BEHIND MOWERS. operators of the mower become thoroughly familiar with the controls, parts and operation of the mower before operating. -
Page 6: Section 2 - Operating Instructions
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check guards, deflectors, grass bag, adapter and covers to make sure all are in place and securely tightened. WARNING DO NOT start or operate this machine without installing the recycling plug or the entire grass... -
Page 7: Starting & Stopping Wheel Drive
Section 2 - OPERATING INSTRUCTIONS 2.2 STARTING & OPERATION 2.2.2. ENGINE & BLADE (Primer Models) (Electric Start) When the ignition key is turned to “START”, the engine will not crank over and will not start unless the blade control is engaged! 1. -
Page 8: Cutting Height Adjustment
Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Remove key. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. -
Page 9: Section 3 - Maintenance Instructions
Manual. Thereafter, change oil after each 25 hours of use. 3.2.2. GREASE LEVEL IN TRANSMISSION maintenance. If transmission leaks or malfunctions, return machine to an authorized Snapper dealer for repair. 3.2.3. WHEEL DRIVE CONTROL The wheel drive control requires periodic adjustment to maintain proper drive function. -
Page 10: Check Mower Blade
Section 3 - MAINTENANCE WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Remove key. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. -
Page 11: Section 4 - Adjustments And Repair
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Remove key. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. -
Page 12: Wheel Drive Control Adjustment
IMPORTANT: DO NOT over-tighten wheel drive control. DO NOT operate if control or drive does not function properly. Contact your local SNAPPER Dealer for assistance. IMPORTANT: If machine creeps forward after wheel drive control is released the cable is too tight and must be readjusted to eliminate all forward movement. -
Page 13: Belt Service
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Remove key. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. -
Page 14: Battery Service
Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine and blade running. STOP engine and blade. Remove key. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. - Page 15 The electrolyte (acid) is a very dangerous, corrosive and poisonous liquid. Follow very carefully all instructions and warnings provided with the kit. Contact your Snapper dealer for assistance. 4.4.7. BATTERY TESTING Battery Condition Chart...
-
Page 16: Troubleshooting
1. Fill fuel tank with fresh fuel to proper level. 2. Push primer button 3 times / choke. 3. Place spark plug wire onto spark plug. 4. Contact authorized SNAPPER dealer. 5. Pull blade control against handle.. 6. Charge or replace with new battery. -
Page 17: Maintenance Schedule
MAINTENANCE SCHEDULE ITEM SERVICE PERFORMED Check Oil Level Engine Oil Initial Oil Change Periodic Oil Change Clean Sponge Element Air Pre-Cleaner Clean or Replace Air Cleaner Replace Spark Plug Drive Belt Check For Wear And Tension Check For Wear, Damage Mower Blade &... -
Page 18: Decal Identification
SAFETY ALERT SYMBOL. OBSERVE AND FOLLOW ALL SAFETY INSTRUCTIONS. READ, UNDERSTAND AND FOLLOW INSTRUCTIONS AND WARNINGS IN OPERATOR’S MANUALS, AND ON THE MOWER, ENGINE AND ATTACHMENTS BEFORE OPERATING. (1) WARNING INSTRUCTIONS. (2) WARNING (DECK): Read and follow Starting and Safety Instructions in Owner’s Manual. Improper use of machine can result in serious injury. - Page 19 GROUND SPEED DECAL P/N 4-7158 (7) GROUND SPEED: Shows direction of movement and the ability to select one of three ground speeds by moving the lever. The number 3 (Rabbit) indicates the top speed, number 2 indicates the medium speed and the number 1 (Turtle) indicates the slowest speed.
-
Page 20: Decal Identification
DECAL IDENTIFICATION CHUTE DEFLECTOR DECAL P/N 4-6924 (13) WARNING: DO NOT operate without grass catcher, side chute or plug installed. AIR FILTER SYMBOL P/N 2-9781 (14) AIR FILTER: Indicates location of engine air filter. To service the filter, read and follow the engine operating and maintenance instructions. -
Page 21: Warranty
For three (3) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both. - Page 22 WALK MOWERS SERIES 2 Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments.