Snapper CP215520HV Safety Instructions & Operator's Manual
Snapper walk mower safety instructions & operator's manual
Hide thumbs
Also See for CP215520HV:
- Parts manual (30 pages) ,
- Parts manual (24 pages) ,
- Operator's manual (28 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Safety Instructions & Operator's Manual for
21" STEEL DECK
WALK MOWERS
COMMERCIAL MODELS
SERIES 20
Models
CP215520HV (7800372)
NOTE: Specifications are correct at time of printing and are subject to change without notice.
* Actual sustained engine power will likely be lower due to operating limitations and environmental factors. Please refer to 'Engine Power Rating Information' for
further details.
Manual No. 7102388 (I.R. 2/25/2008)
TP 100-5363-IR-CW-N
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Snapper CP215520HV
Summary of Contents for Snapper CP215520HV
- Page 1 SERIES 20 Models CP215520HV (7800372) NOTE: Specifications are correct at time of printing and are subject to change without notice. * Actual sustained engine power will likely be lower due to operating limitations and environmental factors. Please refer to ‘Engine Power Rating Information’ for further details.
-
Page 2: Product Registration
Snapper at P.O. Box 1379, McDonough, Georgia 30253. You can contact us at our website (www.snapper.com), or if you would like to speak with a Customer Service Representative, call us at the Snapper Customer Relations Center at 1-800-935-2967. For faster service please have your Serial Number and Model Number available. -
Page 3: Table Of Contents
Table of Contents Operator Safety ..........2 Important Operator Safety Instructions . -
Page 4: Operator Safety
If you have any questions pertaining to your machine which your dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER, McDonough, Georgia 30253. Phone: (1-800-935-2967). Protection for Children Tragic accidents can occur if the operator is not alert to the presence of children. -
Page 5: Maintenance And Storage
10. DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine. 11. Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices. -
Page 6: Features And Controls
Features and Controls IMPORTANT The figures and illustrations in this manual are provided for reference only and may differ from your specific model. Contact your Snapper dealer if you have questions. Features and Controls Oil Fill Cap and Dipstick Fuel Filler Cap... -
Page 7: Starting And Operation
Operation Pre-Start Check List Make the following checks and perform the service required before each start-up. 1. Check the guards, deflectors, grass bag, adapter, and covers to make sure all are in place and securely tightened. 2. Check the blade control (A, Figure 1), wheel drive control (B), and ground speed control (C) to insure they work freely. -
Page 8: Propelling Mower
DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. www.snapper.com... -
Page 9: Cutting Height Adjustment
Operation (Continued) WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Cutting Height Adjustment 1. -
Page 10: Installing The Discharge Deflector
3. Install the nuts onto the studs and tighten securely. Figure 11: Installing the grass bag adapter WARNING DO NOT operate without entire Grass Catcher or guard in place. Grass Catcher components are subject to deterioration during normal use. Inspect frequently and replace worn or damaged components immediately. www.snapper.com... -
Page 11: Installing The Recycling Plug
Operation (Continued) WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Installing the Grass Bag Adapter (Continued) 4. -
Page 12: Installing The Grass Bag
NOTE: An illustration of the Z-Fold is attached to the bag. Figure 15: Removing the bag slider WARNING Grass Catcher bags used on SNAPPER products are made of woven fabric, and are subject to deterioration and wear during normal usage. Check condition of bag before each use. -
Page 13: Maintenance
Maintenance Maintenance - Introduction To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention the model and serial number. -
Page 14: Check Mower Blade
7. Loosen the handle knobs. Carefully fold the handles forward, “flexing” the control cables to prevent cable damage. 8. Store the mower in a shed or other dry area, protected from weather. www.snapper.com... -
Page 15: Mower Blade Replacement
Maintenance (Continued) WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. -
Page 16: Wheel Drive Control Adjustment
The upper clip should be located 2” below the upper knob; the lower clip should be 4” above the lower knob. The cable should slide freely with the clips installed at these locations. www.snapper.com... -
Page 17: Driven And Drive Disc Service
Maintenance (Continued) WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Driven and Drive Disc Service If the mower does not propel itself properly, check for the following problems:... - Page 18 Install a new driven disc ring as follows: 1. Remove the pin and washer (C, Figure 28) from the transfer rod (D), and remove the end of the transfer rod from the hole in the driven disc assembly. www.snapper.com...
-
Page 19: Driven Disc Bearing Replacement
Maintenance (Continued) WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Driven Disc Ring Replacement (Continued) 2. -
Page 20: Belt Service
25 hours of mower operation. Engine Drive Belt Replacement (Stretch Type Belts) 1. Empty the fuel tank. 2. Note the belt routing (Figure 35). There is no idler pulley on these models to disconnect. Figure 35: Engine drive belt routing www.snapper.com... -
Page 21: Transmission Belt Replacement
Maintenance (Continued) WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Engine Drive Belt Replacement (Stretch Type Belts - Continued) IMPORTANT: Drain the fuel tank before tipping the mower. -
Page 22: Service Schedule
Page 11 Page 12 Engine Manual Engine Manual Engine Manual Engine Manual Page 12, 18 Page 13 Page 5 Page 11 Page 11 Page 14-17 EACH SEASON 7078026 7029344 7034604 7019795 7017168 7026691 7026407 7012354 7046784 7073528 7010927 7006155 www.snapper.com... -
Page 23: Troubleshooting
4. Replace belt. 1. Clean debris. 2. Clean or replace driven disc. 3. Replace drive belt. 4. Contact authorized SNAPPER dealer. 1. Adjust cutting height. 2. Move engine speed control to ‘Fast’ position. 3. Move ground speed control to a slower speed. -
Page 24: Warranty
For ninety (90) days from purchase date for the original purchaser’s commercial, rental, or other non-residential use, SNAP- PER, through any authorized SNAPPER dealer will replace, free of charge, any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both. - Page 26 Notes www.snapper.com...
- Page 27 Notes...
- Page 28 (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine. Snapper Products 535 Macon Street McDonough, GA 30253...
Need help?
Do you have a question about the CP215520HV and is the answer not in the manual?
Questions and answers