Terminal Assignment - Honeywell CIPer 50 Installation & Commissioning Instructions

Terminal Assignment

terminal
signal
no.
s1 24V-0 supply voltage (GND), int. connected with term. 31 and system GND (term. 19+37)
2 24V~ supply voltage (24V)
3,4 - not used
5 BO1 Binary output 1. N.O. relay contact switching input power connected to terminal 8
6 BO2 Binary output 2. N.O. relay contact switching input power connected to terminal 8
7 BO3 Binary output 3. N.O. relay contact switching input power connected to terminal 8
8 IN1,2,3 Common relay contact for BO1, BO2, and BO3
9 INX Relay contact for BO4
10 BO4 Binary output 4. N.O. relay contact switching input power connected to terminal 9
Binary output 5. N.O. relay contact switching input power connected to terminal
11 BO5
12
12 IN5 Relay contact for BO5
13 IN6 Relay contact for BO6
Binary output 6. N.O. relay contact switching input power connected to terminal
14 BO6
13
Binary output 7. N.O. relay contact switching input power connected to terminal
15 BO7
16
16 IN7 Relay contact for BO7
17 IN8 Relay contact for BO8
Binary output 8. N.O. relay contact switching input power connected to terminal
18 BO8
17
19 GND Ground terminal (see NOTE below)
20 AO1 Analog output 1
21 AO2 Analog output 2
22 AO3 Analog output 3
23 AO4 Analog output 4
24 GND-1 ref. GND of RS485-1 (isolated)
25 485-1+ "+" signal for RS485-1 (isolated)
26 485-1- "-" signal for RS485-1 (isolated)
27,28 not used
29 485-2+ "+" signal for RS485-2 (non-isolated)
30 485-2- "-" signal for RS485-2 (non-isolated)
ref. GND of RS485-2, int. conn. with 24V-0 (term. 1) and system GND (term.
31 GND-2
19+37)
32 - not used
33 BI1 Binary input 1 (static dry contact) / pulse counter (fast totalizer)
34 BI2 Binary input 2 (static dry contact) / pulse counter (fast totalizer)
35 BI3 Binary input 3 (static dry contact) / pulse counter (fast totalizer)
36 BI4 Binary input 4 (static dry contact) / pulse counter (fast totalizer)
37 GND Ground terminal (see NOTE below)
38 UI9 Universal input 9 (for NTC10kΩ / NTC20kΩ / 0...10 V / slow BI)
39 UI10 Universal input 10 (for NTC10kΩ / NTC20kΩ / 0...10 V / slow BI)
40 UI1 Universal input 1 (for NTC10kΩ / NTC20kΩ / 0...10 V / slow BI)
41 UI2 Universal input 2 (for NTC10kΩ / NTC20kΩ / 0...10 V / slow BI)
42 UI3 Universal input 3 (for NTC10kΩ / NTC20kΩ / 0...10 V / slow BI)
43 UI4 Universal input 4 (for NTC10kΩ / NTC20kΩ / 0...10 V / slow BI)
44 UI5 Universal input 5 (for NTC10kΩ / NTC20kΩ / 0...10 V / slow BI)
45 UI6 Universal input 6 (for NTC10kΩ / NTC20kΩ / 0...10 V / slow BI)
46 UI7 Universal input 7 (for NTC10kΩ / NTC20kΩ / 0...10 V / slow BI)
47 UI8 Universal input 8 (for NTC10kΩ / NTC20kΩ / 0...10 V / slow BI)
NOTE: All AOs, UIs, and BIs share the same ground potential. It is thus possible to connect just one combined GND
signal for all AOs, UIs, and BIs. Auxiliary terminals may be used if needed.
CIPer MODEL 50 CONTROLLER – INSTALLATION & COMMISSIONING INSTRUCTIONS
Table 8. Terminal assignment
Description
17
WEB-EAGLENX26XX
X
X
-
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
X
X
X
-
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
31-00233EFS-01