Advertisement
Quick Links
#7600023 & 7600024 TWIN BAG CATCHER KIT FOR
38 & 42" SNAPPER / SIMPLICITY RZT RIDING MOWERS
7600023
7600024
!
DO NOT attempt any adjustments, maintenance, repairs, or service with engine running. Stop engine. Engage
parking brake. Remove key. Remove spark plug wire and secure wire away from spark plug. Engine, muffler and
surrounding areas are extremely hot. Avoid serious burns; allow components to cool down before installing kit.
Replace worn or damaged parts prior to operating. Use approved fuel container. DO NOT smoke near open fuel
container. DO NOT fill fuel tank indoors or when engine is running. Allow engine to cool for at least ten minutes
before refilling. Make sure that fuel cap is tightened securely. Wipe off any spilled fuel before starting engine.
STEP 1 (38" Units Only): Install one air lift onto the topside
of each of the four blade tips, securing with three 5/16-24 x
5/8" oval head machine screws, internal tooth lock washers
and hex nuts. See Figure 1. Torque hardware to 12 ft-lbs.
WASHER
AND NUT (3)
STEP 2: Install the baffle to the front of the mower deck:
38" Decks - Secure the baffle with one 5/16 x 3/4" hex head
cap screw, flat washer and center lock nut on one end, and
the existing hardware on the other end. See Figure 2.
42" Decks - Secure the baffle with two 5/16 x 5/8" pan head
machine screws and flange lock nuts. See Figure 3.
NOTE: One or more holes may have to be drilled into the
deck in order to install the baffle. If so, install the baffle as
fully onto the deck as possible with the existing holes, then
drill the remaining holes with an 11/32" drill, using the baffle
hole(s) as a template.
TWIN BAG CATCHER KIT FOR 38" SNAPPER / SIMPLICITY RZT RIDING MOWER
TWIN BAG CATCHER KIT FOR 42" SNAPPER / SIMPLICITY RZT RIDING MOWER
NOTE: Refer to the parts lists at the end of this manual for
additional assistance with component identification.
SECURE AIR LIFT
TO TOP OF BLADE
FIGURE 1
WARNING
38" DECK
HEX HEAD CAP
SCREW
MACHINE
SCREW (3)
42" DECK
NOTE: CASTER
MAY DIFFER FROM
ONE SHOWN
INSTALL BAFFLE TO OUTSIDE
FRONT OF DECK
INSTRUCTION No. 7100642 (Rev. 2, 12/14/2006)
1
WASHER AND
LOCK NUT
FIGURE 2
(Components removed for clarity)
FIGURE 3
!
USE
EXISTING
NUTS
INSTALL BAFFLE
TO OUTSIDE
FRONT OF DECK
MACHINE
SCREW (2)
LOCK NUT (2)
TP 200-5173-R2-AT-SN
Advertisement
Related Manuals for Snapper 7600023, 7600024
Summary of Contents for Snapper 7600023, 7600024
- Page 1 #7600023 & 7600024 TWIN BAG CATCHER KIT FOR 38 & 42” SNAPPER / SIMPLICITY RZT RIDING MOWERS 7600023 TWIN BAG CATCHER KIT FOR 38” SNAPPER / SIMPLICITY RZT RIDING MOWER 7600024 TWIN BAG CATCHER KIT FOR 42” SNAPPER / SIMPLICITY RZT RIDING MOWER DO NOT attempt any adjustments, maintenance, repairs, or service with engine running.
- Page 2 STEP 3: Remove the two innermost front carriage bolts securing the unit footrest to the frame. Install the four ballasts against the front of the machine, securing with the supplied 5/16 x 1-3/4” carriage bolts and lock nuts in place of those removed.
- Page 3 STEP 5: Install the bag adapter (42” Deck): a. Remove the wing nuts, split lock washers, flat washers, and hex nuts that secure the deflector to the deck, and remove the deflector. See Figure 8. REMOVE NUTS AND WASHERS FIGURE 8 b.
- Page 4 STEP 8: Install the U-tube onto the top of the bagger chan- nel, securing with three 5/16-24 x 1-5/8” curved head bolts, split lock washers, and hex nuts. See Figure 13. Tighten hardware securely. U-TUBE WASHER & NUT (3) BACK OF BAGGER CHANNEL FIGURE 13 STEP 9: Install the center tube into the center of the bagger...
- Page 5 STEP 12: Assemble the discharge tubes: a. Install one strap assembly to each of the locations marked ‘A’ in Figure 19. Insert one #10-24 x 5/8” pan head screw, fitted with one #10 x 1/2” OD flat washer, out through the hole in the tube or adapter.
- Page 6 STEP 13: Assemble the grass containers: a. Match the numbers on the side of each container segment with its corresponding segment. ‘1’s and ‘2’s designate the first container, ‘3’s and ‘4’s designate the second. See Figure 21. b. With the matched numbers aligned, insert the bottom segment of each container through the middle segment, and the middle segment through the top segment, until the tabs around the top of each segment lock the segment in place.
- Page 7 Operation: WARNING To prevent injury or damage, always follow the operating instructions supplied with your machine when operating the bagger. To use the bagger: -Start the engine. -Move the throttle control to the fast position. -To fill the containers, always operate at a slow ground speed.
- Page 8 TWIN BAG CATCHER COMPONENTS - 38” RZT / JAVELIN...
- Page 9 TWIN BAG CATCHER COMPONENTS - 38” RZT / JAVELIN ITEM NO. PART NO. 7100658 7100659 1673320 1910531 1732490 1732488 1732489 1732819 720524 7091530 7091294 7091603 720525 7091503 720537 7036415 7091290 1732867 720529 720530 720079 7091315 7091297 720339 720553 7016704 7400094 7091541 7091601 7900034...
- Page 10 TWIN BAG CATCHER COMPONENTS - 38” RZT / JAVELIN...
- Page 11 TWIN BAG CATCHER COMPONENTS - 38” RZT / JAVELIN ITEM NO. PART NO. 7091318 7300369 7060480 7037723 7090228 7090391 7300367 7900039 DESCRIPTION HEX HEAD CAP SCREW, 5/16 X 3/4 GR5 BAFFLE, 38" DECK - RZT AIR LIFT KIT - COMPLETE AIR LIFT OVAL HEAD MACHINE SCREW, 5/16-24 X .656 INTERNAL TOOTH LOCK WASHER 5/16...
- Page 12 TWIN BAG CATCHER COMPONENTS - 42” RZT / JAVELIN...
- Page 13 TWIN BAG CATCHER COMPONENTS - 42” RZT / JAVELIN ITEM NO. PART NO. 7100658 ASSY., TWIN COVER - 38/42 7100659 1673320 1910531 1732490 1732488 1732489 1732819 720524 HINGE, COVER 7091530 CARRIAGE BOLT, 1/4-20 X 1/2 7091294 WASHER, SAE, 1/4 7091603 HEX CENTER LOCK NUT, 1/4-20 720525 PIN, COVER HINGE...
- Page 14 TWIN BAG CATCHER COMPONENTS - 42” RZT / JAVELIN...
- Page 15 TWIN BAG CATCHER COMPONENTS - 42” RZT / JAVELIN ITEM NO. PART NO. 7091613 PAN HEAD MACHINE SCREW, 5/16-18 X 3/4 7300386 BAFFLE, 42" DECK - RZT 7300367 BALLAST-TWIN BAG CATCHER - RZT 7900039 CARRIAGE BOLT, 5/16-18 X 1.75 GR5 DESCRIPTION...
- Page 16 INSTRUCTION No. 7100642 (Rev. 2, 12/14/2006) TP 200-5173-R2-AT-SN...