Page 1
ASSEMBLY INSTRUCTIONS OPERATOR’S MANUAL PARTS LIST Actual product may differ slightly from product pictured above Manual No. 7078092 (I.R. - 09/14/04) European Extreme Series Walk-Behind Leaf Blower Series 1 Models covered: ELBX10151BV (Part # 7085912)
You have just purchased one of the finest pieces of outdoor power equipment on the market today. If properly cared for, your new blower will provide years of dependable service. Please read and follow this instruction manual carefully in order to get the most out of your new equipment.
• Do not operate in reverse unless absolutely necessary. Always look down and behind before and while traveling in reverse. • Be aware of the blower discharge direction and do not point it at anyone. Do not operate the blower without deflectors in place.
The operator could lose footing or balance or blower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in. • Do not operate on slopes with wet grass. Reduced footing or traction could cause sliding.
Note: Please refer to Parts List for correct part identification and placement. FRONT WHEEL ASSEMBLY • Place Mounting Bracket against lower right corner of Blower Housing, aligning holes in bracket with threaded studs in housing. Secure with three 3/8-16 hex nuts, split lock washers and flat washers. Tighten securely.
unit operation STARTING THE ENGINE IMPORTANT NOTE: The procedures outlined within this section are general guidelines, and are in no way meant to replace or supercede engine manufacturer’s operating instructions. In order to obtain optimum performance from your engine, refer to your engine manual. WARNING! IMPELLER IS MOUNTED DIRECTLY TO ENGINE SHAFT –...
BLOWER OPERATION DANGER! DO NOT PASS BY OR STAND ON THE AIR DISCHARGE SIDE OF ANY LEAF BLOWER WITH THE ENGINE RUNNING. HIGH VELOCITY DISCHARGE CAN EASILY TURN HARMLESS DEBRIS INTO FLYING PROJECTILES. DANGER! NEVER INSERT ANY BODY PART OR FOREIGN OBJECT INTO ANY OPENING WHILE UNIT IS RUNNING.
Page 8
This feature is ideal for such things as blowing debris from a wall or fence.
Page 9
LUBRICATION: • The tires on your blower contain bearings that should be lubricated on a weekly basis using a high- performance, automotive quality grease to ensure long life and minimal wear. Check all adjustments periodically.
maintenance (cont.) BEFORE MAKING ANY ADJUSTMENTS, STOP ENGINE AND DISCONNECT SPARK PLUG WIRE TO PREVENT INADVERTENT STARTING OF UNIT. TROUBLESHOOTING: • UNIT WILL NOT START: • Check fuel and oil levels. • Check to make sure choke is set when engine is cold, off when hot. •...
maintenance (cont.) ADJUSTMENTS: BEFORE MAKING ANY ADJUSTMENTS, STOP ENGINE AND DISCONNECT SPARK PLUG WIRE TO PREVENT INADVERTENT STARTING OF UNIT. • THROTTLE CABLE ADJUSTMENT: Correct cable adjustment allows for full range of movement of throttle body on engine in conjunction with throttle control on handle. To adjust, loosen cable clip screw on engine, then slide cable housing in or out in approximately 1/8-1/4”...
Page 13
1717312 33866 3023276 74422 91189 Description WELDMENT, Housing- Extreme Blower, LBX10151BV DECAL – See DECAL IDENTIFICATION ENGINE, B&S 10HP Intek OHV Briggs Model 205412 Type 0121-E1 SCREW, 5/16-18 x 1-1/2 Hex Head Cap, GR5 NUT, 5/16-18 Hex Flange Lock, GR5 DECAL –...
Page 14
illustrated parts list (cont’d) Item Part No. 90391 3071800 3031220 90505 90188 76978 91298 ----- ----- ----- ----- ----- Description WASHER, 5/16" Internal Tooth Lock THROTTLE CONTROL, Briggs BUSHING, Flanged .375 x .500 x .25 (.625 x .063 Flange) SCREW, 1/4-20 x 2" Hex Head Cap, GR5 WASHER, .34 x .69 x .08 Flat NUT,1/4-20 Hex Nyloc NUT, 5/16-18 Hex Nyloc...
Page 15
29776 – EUROPEAN CERTIFICATION – LOCATED ON REAR OF BLOWER HOUSING 75892 – DANGER – FLYING MATERIAL – LOCATED ON SIDE OF BLOWER HOUSING 78069 – NOISE RATING – LOCATED ON REAR OF BLOWER HOUSING 75893 – EAR/NOSE/BREATHING PROTECTION REQUIRED –...
Page 16
LOCATED ON INTAKE BAFFLE 3046585 – GIANT-VAC EXTREME LOGO – LOCATED ON INTAKE BAFFLE (ON APPLICABLE MODELS) 75760 – SNAPPER LOGO – LOCATED ON INTAKE BAFFLE (ON APPLICABLE MODELS) 75861 / 29445 – GIANT-VAC LOGO – LOCATED ON MID-HANDLE PANEL (ON APPLICABLE MODELS) 1722551 –...
Need help?
Do you have a question about the ELBX10151BV and is the answer not in the manual?
Questions and answers