Smeg A1AU6 Important Safety Instructions
Smeg A1AU6 Important Safety Instructions

Smeg A1AU6 Important Safety Instructions

Smeg hood instruction manual
Hide thumbs Also See for A1AU6:

Advertisement

Important Safety Instruction

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS – Your safety and the safety of others are very important.
We have provided many important safety messages throughout this manual and on the appliance.
Read all instructions before using the appliance and always obey all safety messages.
RECOGNIZE SAFETY INFORMATION
This is a safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and
others.
UNDERSTAND SIGNAL WORDS
A signal word – DANGER, WARNING, or CAUTION – is used with the safety-alert symbol. DANGER
identifies the most serious hazards. It means you can be killed or seriously injured if you do not
immediately follow the instructions. WARNING means you can be killed or seriously injured if you do not
follow the instructions. CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
All safety messages will inform you of potential hazards, on how to reduce the risk of injury and what
can occur if the instructions are not followed.
IMPORTANT: Observe all governing codes and ordinances.
WARNING: For your safety, the information in this manual must be followed to minimize the risk
of fire or explosion, or to prevent property damage, personal injury or death.
-
This conversion kit must be installed by a qualified service agency in accordance with the
manufacturer's instructions and all applicable codes and requirements of the authority
having jurisdiction.
-
The qualified service agency is responsible for the proper installation of this kit.
-
The installation shall not be considered to be correct and completed until the operation of the
converted appliance is checked as specified in the manufacturer's instructions supplied with
this kit.
FIRE HAZARD
WARNING
Securely tighten all gas connections. If connected to LP, have a qualified
person ensure that the gas pressure does not exceed 14" water column.
Examples of a qualified person include licensed heating personnel,
authorized gas company personnel, and authorized service personnel.
FAILURE TO DO SO CAN RESULT IN DEATH, EXPLOSION, OR FIRE.
3

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the A1AU6 and is the answer not in the manual?

Questions and answers

Summary of Contents for Smeg A1AU6

  • Page 1: Important Safety Instructions

    Important Safety Instruction IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS – Your safety and the safety of others are very important. We have provided many important safety messages throughout this manual and on the appliance. Read all instructions before using the appliance and always obey all safety messages. RECOGNIZE SAFETY INFORMATION This is a safety alert symbol.
  • Page 2 Check that the main gas supply line to the range is shut off and that the power supply cord is disconnected. Remove access cap “A” by using a screwdriver or a quarter, turning the access cap counter-clockwise. The gas pressure regulator has two settings which are indicated on two sides of the cap. Turn the cap and reinstall it in the regulator with "LP"...
  • Page 3 Conversion Kit This operation requires no primary air regulation. 1 Extract the grids and remove all the caps and flame-spreader crowns; 2 Unscrew the burner nozzles with a 7 mm socket wrench; 3 Replace the nozzles according to the type of gas to be used and the description in paragraph 3.2 “Burner and nozzle characteristics table”.
  • Page 4 To adjust the cooktop for LP gas or to return to Natural Gas use, refer to the tables below. Front Right Front Left Inner Central Outer Rear Right Rear Left Front Right Front Left Inner Central Outer Rear Right Front Left NOTE: Save the nozzles removed from the appliance for future use.
  • Page 5 Minimum adjustment for Natural Gas Light the burner and take it to the minimum. Remove the gas tap knob and turn the adjustment screw inside or at the side of the tap shaft (depending on the model) until there is a regular minimum flame. Replace the knob and check burner flame stability: (rapidly turning the knob from maximum to minimum position, the flame should not go out).

Table of Contents