Specifications - Makita TM3000C Instruction Manual

ENGLISH (Original instructions)
1-1. Slide switch
2-1. Dial
3-1. Application tool installation bolt
3-2. Holes in the application tool

SPECIFICATIONS

Oscillation per minute
Oscillation angle, left/right
Net weight
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for sawing and cutting wood, plastic,
gypsum, non-ferrous metals, and fastening elements (e.
g. unhardened nails and staples). It is also intended for
working soft wall tiles, as well as dry sanding and
scraping of small surfaces. It is especially for working
close to edge and flush cutting.
Noise
The typical A-weighted noise level determined according
to EN60745:
Work mode: Sanding
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Work mode: Cutting with plunge cut saw blade
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Work mode: Cutting with segmental saw blade
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Work mode: Scraping
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
Explanation of general view
3-3. Protrusions of the tool flange
4-1. Application tool installation bolt
4-2. Hex wrench
4-3. Tighten
Model
Overall length
without dust extraction attachment
with dust extraction attachment
Safety class
) : 74 dB(A)
pA
) : 78 dB(A)
pA
) : 76 dB(A)
pA
) : 77 dB(A)
pA
ENE080-1
Vibration
The vibration
determined according to EN60745:
Work mode: Sanding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: Cutting with plunge cut saw blade
ENG905-1
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: Cutting with segmental saw blade
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: Scraping
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
•
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
3
5-1. Application tool installation bolt
5-2. Holes in the application tool
5-3. Adapter
5-4. Protrusions of the tool flange
TM3000C
-1
6,000 - 20,000 (min )
1.6 ﾟ (3.2 ﾟ total)
275 mm
1.4 kg
1.5 kg
/II
total value (tri-axial
2
) : 2.5 m/s or less
h
2
2
) : 6.5 m/s
h
2
2
) : 3.0 m/s
h
2
2
) : 5.5 m/s
h
2
ENG900-1
vector sum)
ENG901-1