Table of Contents
Advertisement
Quick Links
1. Precautions for safety and use_________________________ 4
2. Fitting the appliance in the top _________________________ 5
2.1 Fixing to the supporting structure ________________________________________5
3. Electrical connection ________________________________ 7
3.1 Clearance above and around domestic appliances __________________________8
3.2 Room ventilation _____________________________________________________9
3.3 Discharge of combustion products _______________________________________9
4. GAS CONNECTION________________________________ 10
5. Adapting to different types of gas______________________ 11
5.1 Removing the hob skin _______________________________________________11
5.2 Adjusting for bottled gas ______________________________________________12
5.3 Adjusting for natural gas ______________________________________________12
5.4 Adjusting the primary air flow __________________________________________13
5.5 Reassembling the hob skin____________________________________________13
5.6 Adjusting the minimum setting for natural gas and town gas __________________13
5.7 Adjusting the minimum for bottled gas ___________________________________13
5.8 Hob burner layout ___________________________________________________14
5.9 Greasing the gas taps________________________________________________14
6. Description of controls ______________________________ 15
6.1 The front panel _____________________________________________________15
7. Using the hob _____________________________________ 16
7.1 Lighting burners with safety device______________________________________16
7.2 Positioning the griddle plate ___________________________________________16
7.3 Practical hints for using the burners _____________________________________16
7.4 Pan diameters______________________________________________________17
8. Cleaning and maintenance __________________________ 18
8.1 Cleaning stainless steel ______________________________________________18
8.2 Cleaning the components _____________________________________________18
THESE INSTRUCTIONS ONLY APPLY TO THE COUNTRIES OF DESTINATION WHOSE
IDENTIFICATION SYMBOLS ARE LISTED ON THE COVER OF THIS MANUAL.
THIS BUILT-IN HOB IS CLASSIFIED AS CLASS 3.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the authorised
person who is to check the gas supply system and install, commission and test the
appliance.
INSTRUCTIONS FOR THE USER: these provide recommendations for use, a
description of the controls and the correct procedures for cleaning and maintaining the
appliance.
Table of contents
3
Advertisement
Table of Contents
Related Manuals for Smeg PTSA727X
Summary of Contents for Smeg PTSA727X
-
Page 1: Table Of Contents
Table of contents 1. Precautions for safety and use_________________________ 4 2. Fitting the appliance in the top _________________________ 5 2.1 Fixing to the supporting structure ________________________________________5 3. Electrical connection ________________________________ 7 3.1 Clearance above and around domestic appliances __________________________8 3.2 Room ventilation _____________________________________________________9 3.3 Discharge of combustion products _______________________________________9 4. -
Page 2: Precautions For Safety And Use
Precautions for Safety and Use Precautions for safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB'S LIFE CYCLE. USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT CONTAINS BEFORE USING THE HOB. -
Page 3: Fitting The Appliance In The Top
Instructions for the Installer Fitting the appliance in the top The procedures required below must be carried out by a skilled builder and/or joiner. The hob can be installed on various materials, including masonry, metal, solid wood and wood finished with plastic laminates, provided the material is heat-resistant (T 90°... - Page 4 Instructions for the Installer edge of the gasket B. The dimensions in the drawing below refer to the hole on the inside edge of the gasket. In case of installation on a hollow compartment with doors, a separating panel has to be placed under the hob.
-
Page 5: Electrical Connection
Instructions for the Installer Electrical connection Check that the power supply line voltage and size are as specified on the nameplate underneath the appliance's casing. This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant regulations. -
Page 6: Clearance Above And Around Domestic Appliances
Instructions for the Installer 3.1 Clearance above and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (Measurement A) Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions. However, in no case shall the clearance between the highest part of the hob of the cooking appliance and a range hood be less than 600 mm or, for an overhead exhaust fan, 750 mm. -
Page 7: Room Ventilation
Instructions for the Installer NOTES 1 Requirement 3 does not apply to a freestanding or elevated cooking appliance which is designed to prevent flames or the cooking vessels from extending beyond the periphery of the appliance. 2 The ‘cooking surface area’ is defined as that part of the appliance where cooking normally takes place and does not include those parts of the appliance containing control knobs. -
Page 8: Gas Connection
Instructions for the Installer GAS CONNECTION This appliance is suitable for installation with Natural Gas or LPG (propane). Refer to page 12 for the relevant burner pressure and appropriate injector sizes. When the appliance is to be connected to Natural Gas then the pressure regulator supplied must be fitted to the gas inlet. -
Page 9: Adapting To Different Types Of Gas
Instructions for the Installer Adapting to different types of gas Before carrying out the operations described below, disconnect the appliance from the electricity supply. The hob of the cooker is adjusted for use with either natural gas at a pressure of 1.0 kPa. -
Page 10: Adjusting For Bottled Gas
Instructions for the Installer Adjusting for bottled gas Undo the screw A and push the support B fully down. Remove the nozzle C with a spanner and fit the suitable one following the instructions in the tables referring to the type of gas to be used. -
Page 11: Adjusting The Primary Air Flow
Instructions for the Installer Adjusting the primary air flow Refers to the gap “X” in mm. BURNER Auxiliary Semi rapid Rapid (3) Rapid (6) Rapid (7) WOK double flame Internal (4-8) External Reassembling the hob skin Reverse the procedure described in point “5.1 Removing the hob skin ”. When replacing the burner rings, bear in mind that they must be fully tightened using the spanner provided. -
Page 12: Hob Burner Layout
Instructions for the Installer Hob burner layout Greasing the gas taps Over time, the gas taps may become stiff or jam. Clean their insides and change their lubricating grease. This operation must be carried out by a skilled technician. Burner type 1 Auxiliary 2 Semi rapid 3 Rapid... -
Page 13: Description Of Controls
Instructions for the User Description of controls The front panel All the hob's control and monitoring devices are placed together on the front panel. KNOB OPERATING MODE To light the flame, press the knob and at the same time turn it anti-clockwise to the minimum flame symbol . -
Page 14: Using The Hob
Instructions for the User Using the hob Check that the fixing rings, burners, flame diffuser rings and pan stands are fitted correctly. The burner pins A must be fitted into the recesses B in the flame diffuser ring. The holes C in the flame diffuser ring must mate with the ignition plugs and thermocouples D on the hob. -
Page 15: Pan Diameters
Instructions for the User 7.4 Pan diameters BURNERS min. and max. Ø (in cm) 1. Auxiliary 2. Semi rapid 3. Rapid 4. WOK double flame 5. WOK 6. Rapid 7. Rapid 8. WOK double flame 7-18 10-24 18-24 20-28 20-28 18-24 18-24 20-28... -
Page 16: Cleaning And Maintenance
Instructions for the User Cleaning and maintenance Before carrying out any operations, disconnect the appliance from the electricity supply. Cleaning stainless steel To keep the hob in good condition, it must be cleaned regularly, after each use, first allowing it to cool. 8.1.1 Routine daily hob cleaning When cleaning and caring for stainless steel surfaces, always use only specific...