Honeywell Spyder PUL1012S Manual page 14

SPYDER® LON PROGRAMMABLE, VAV/UNITARY CONTROLLERS
All controllers have the terminal arrangements similar to the
examples shown in Fig. 16 and Fig. 17 as described in Table
Table 6 on page 13 and Table 7 on this page.
N ®
SERVICE PIN
EURON
The N ® Service Pin pushbutton (when pressed)
EURON
transmits the Service Message to the network, regardless of
the controller's current mode of operation (see Fig. 16 and Fig.
17).
CAUTION
Equipment Damage Hazard.
Can cause controller damage or failure.
Do not use any metal object to press the N
Service Pin. Use a plastic rod or wood device (such as
a pencil with the lead broken off) to press the pin. Using
a metal object can damage the circuitry of the
controller.
LONWORKS BUS CONVENIENCE JACK
The L W Bus connection is provided by plugging the
ON ORKS
®
Serial L T Adapter (SLTA) connector into the
ON ALK
L W ® Bus Jack (see Fig. 16 and Fig. 17).
ON ORKS
2 2 2 2 2 2 2 2 3 2
1 2 3 4 5 6 7 8 0
1 2 3 4 5 6 7 8
TERMINALS 1-8
®
LONWORKS BUS JACK
NEURON
(LABELLED SRV JCK)
(LABELLED SRV PIN)
Fig. 16. Controller Terminal Connections, N
Pin, & LONWORKS® Bus Jack for the PUL6438S,
PVL6436AS, and PVL6438NS (PVL6438NS shown).
63-2685—03
EURON
TERMINALS 21-40
3 3 3 3 3 3 3 3 4 3
9 1 2 3 4 5 6 7 8 0 9
1 1 1 1 1 1 1 1 2 1 1
9 0 1 2 3 4 5 6 7 8 0 9
TERMINALS 9-20
®
SERVICE PIN
M23561B
® Service
EURON
®
LONWORKS ® BUS JACK (LABELLED SRV JACK)
NEURON® SERVICE PIN (LABELLED SRV PIN)
Fig. 17. Controller terminal connections, NEURON®
Service Pin and LONWORKS® Bus Jack for the PUL1012S,
PUL4024S, PVL0000AS, PVL4022AS, and PVL4024NS
Wiring Applications (Examples)
Fig. 18–Fig. 24, beginning on page 15, illustrate controller
wiring for the following configurations.
• Typical controller wiring for VAV application using the TR23
Wall Module and a C7770A Air Temperature Sensor (see
Fig. 18 on page 15).
• Typical controller wiring for VAV application with staged
reheat (see Fig. 19 on page 16).
• Typical controller wiring for PWM reheat and PWM
peripheral heat valve actuator (see Fig. 20 on page 17).
• Typical controller wiring for AHU application (see Fig. 21 on
page 18).
• Typical controller wiring for 4 to 20 mA enthalpy sensors
and digital inputs (see Fig. 22 on page 19).
• Typical controller wiring for 4 to 20 mA heating, cooling, and
model ML6161 floating motor control (see Fig. 23 on
page 20).
• Typical controller wiring for a pneumatic transducer, model
RP7517B (see Fig. 24 on page 21).
14
TERMINALS 13-24
1 1 1 1 1 1 1 2 2 2 2 2
3 4 5 6 7 8 9 0 1 2 3 4
1 1
1 2 3 4 5 6 7 8 9 0 1 2
TERMINALS 1-12
(PVL4024NS shown).
M28650