Advertisement
Table of Contents
655 Eisenhower Drive
Owatonna, MN 55060 USA
Phone: (507) 455-7000
Tech. Serv.: (800) 533-6127
Order Entry: (800) 533-6127
International Sales: (507) 455-7223
Fax: (507) 455-7063
These instructions are intended for various shop presses. Some models are shipped assembled and require a minor
amount of assembly; others are shipped unassembled and require complete assembly. The complete assembly
procedure is provided in the following instructions for your reference. Verify the contents of the shipping carton against
the parts list provided to ensure all parts are present before beginning assembly.
WARNING: To prevent personal injury,
• Read and carefully follow the operating instructions and safety precautions for the press and
hydraulic cylinder. Most problems are caused by incorrect assembly or operation.
• The owner of the press must ensure the press is installed and operated according to Federal
(OSHA), state, and local safety standards.
• A press can exert an extremely high force at a moderate hydraulic pump pressure. If you have
any questions about how much force is exerted at a given pressure, contact Technical Services.
• This press is designed for shop maintenance applications. For use in other applications, contact
Technical Services.
Operation
• Wear eye protection that meets ANSI Z87.1 and OSHA standards. Keep hands away from the work
area. Locate the press in an isolated area or shield it to minimize danger to others. Hydraulic
pressure can cause materials to break, possibly resulting in personal injury.
• It is impossible for the manufacturer to provide practical, all-purpose shielding because this is a
general purpose press used in many different applications. The owner of the press must supply
shielding (such as the 1230PB or 2036PB available through OTC) that is practical and specific
for a particular application.
• A work piece must be well supported and aligned to prevent slippage and breakage.
• To prevent accidental slippage, do not place work piece on the press bed or apply hydraulic force
until all bolster pins are in place and all tension has been removed from the bolster lift cables.
• Do not stress adapters beyond their capacities. Pushing or pulling adapters used with this press
must have a maximum tonnage rating equal to, or greater than, the maximum tonnage rating of
the press. Otherwise, breakage may occur.
• The user must ensure all safety-related decals are installed, maintained, and replaced when
necessary.
• Keep hands, feet, legs, etc. out from under the bolster. Accidental slippage can result in personal
injury.
© Bosch Automotive Service Solutions Inc.
Fax: (800) 955-8329
Fax: (800) 283-8665
Shop Press Frame
Maximum Capacity: 55 Tons
Safety Precautions
Assembly & Operating Instructions for:
014-00094
014-00095
Sheet No.
Issue Date: Rev. G November 6, 2015
Form No. 102525
1852
211750
1850
61309
1851
1 of 2
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for OTC 014-00094
Summary of Contents for OTC 014-00094
-
Page 1: Safety Precautions
• It is impossible for the manufacturer to provide practical, all-purpose shielding because this is a general purpose press used in many different applications. The owner of the press must supply shielding (such as the 1230PB or 2036PB available through OTC) that is practical and specific for a particular application. - Page 2 Assembly & Operating Instructions Form No. 102525, Sheet 1 of 2, Back WARNING (cont’d) • To prevent accidental cable breakage, never raise or lower the bolster while there is a load on it. • When lowering the bolster, remove the work piece. Place one support pin all the way through each front and the back upright in the highest hole under the bolster that will not interfere with the new bolster position.
- Page 3 Assembly & Operating Instructions Form No. 102525 Assemble with cylinder mounting plate hole on lower lip of upper bolster. Bolster lifting plate must face up. Long End Goes to Left Side Short End Goes to Right Side Right Left Side Side Bare End Goes to Winch...
- Page 4 Assembly & Operating Instructions Form No. 102525, Sheet 2 of 2, Back Hydraulic Connections Note: Refer to Figure 1 on previous page for location of item numbers referenced below. Also, step 1 only applies to press frames where the hydraulic pump is mounted to the side of the frame — some pumps rest directly on the floor and do not require a pump mounting bracket.
Need help?
Do you have a question about the 014-00094 and is the answer not in the manual?
Questions and answers