Recording From The Turntable; Recording A Cd - Sony LBT-N350 Operating Instructions Manual

Recording From the
Turntable (For the
model supplied with
the turntable only)
You can record from the supplied turntable
PS-LX56P onto a tape. Use TYPE (normal)
or TYPE (CrO ) tape.
2
If your system is not supplied with the
turntable, see "Connecting Optional
Equipment".
SYSTEM
1,8
POWER –ON
7
GB
14
1
Place a record on the turntable.
2
Press EJECT and insert a blank tape
into deck B with the side you want to
record on facing forward.
Recording will start from the front side
of the tape, unless you have changed the
playing direction before recording.
Make sure the tabs on the cassette have
not been removed.
3
Select dual or single-sided recording.
To record
One side
Both sides*
* Recording always stops at the end of the
reverse side. Be sure to start from the
front side.
4
When you want to reduce the hiss noise
in low-level high-frequency signals, set
DOLBY NR to ON.
5
Press FUNCTION until "PHONO"
appears in the display.
6
Press REC.
The REC and (pause) lamps light
and deck B stands by for recording.
Chapter 5: the Tape Player
The
flashes for a few seconds, then
disappears.
If you want to start recording from the
reverse side, press
lamp lights steadily.
7
Press
Recording starts.
8
Play a record (See "Playing a Record"
for details).
To stop recording.
Press
Adjusting the volume or DBFB will not
affect the recording level
But these controls will change the sound
levels you hear through speakers or
headphones.
6
5
3

Recording a CD

4
You can record from a CD to a tape. Use
2
TYPE (normal) or TYPE
To listen to other sources while recording,
you must stop recording.
Recording a CD
Automatically
By using CD SYNCHRO button, you can
record from a CD to a tape easily. Use the
buttons on the unit for this operation.
Set DIRECTION
MODE to
or RELAY
1
Press
Then, press
close the tray. Make sure the CD you
want to record is on the front tray.
lamp lights and the lamp
Side in recording
pause mode
so that the
to release recording pause.
.
(CrO ) tapes.
2
SYSTEM
POWER –ON
1
OPEN/CLOSE and place a CD.
OPEN/CLOSE again to
Total number of tracks and the total
playing time appear in the display.
2
Press EJECT and insert a blank tape
into deck B with the side you want to
record on facing forward.
Recording will start from the front side
of the tape, unless you have changed the
playing direction before recording.
Make sure the tabs on the cassette have
not been removed.
3
Select dual or single-sided recording.
To record
One side
Both sides
4
When you want to reduce the hiss noise
in low-level high-frequency signals, set
DOLBY NR to ON.
5
Press CD SYNCHRO.
The REC and
and deck B stands by for recording.
The lamp lights and the
flashes for a few seconds, then
disappears.
If you want to start recording from the
reverse side, press
lamp lights steadily.
6
Press to release recording pause.
Recording starts.
After about 10 seconds, the CD starts
playing. If the last track on side A has
abruptly been cut, the track will record
again from the beginning on side B
when you choose dual-sided recording.
If you set DIRECTION MODE to
RELAY, recording always stops at the
end of the reverse side.
To stop recording
Press .
6
Note
• Turn the audio emphasis off when the
5
sound level of the CD you want to record
3
is very high, because it may distort the
4
recording sound.
2
Adjusting the volume or DBFB will not
affect the recording level
But these controls will change the sound
levels you hear through speakers or
headphones.
Set DIRECTION
MODE to
or RELAY
(pause) lamps light
lamp
Side in recording
pause mode
so that the
or