1. Manuals
  2. Brands
  3. SMC Networks Manuals
  4. Wireless Router
  5. Barricade SMC7908VoWBRA2
  6. User manual

SMC Networks Barricade SMC7908VoWBRA2 User Manual

Wireless 4-port voip adsl2/2+ modem router
Hide thumbs Also See for Barricade SMC7908VoWBRA2:
Table of Contents

Advertisement

Quick Links

Download this manual

USER GUIDE

Barricade™ VoIP
SMC7908VoWBRA2
Wireless 4-port VoIP ADSL2/2+ Modem Router

Advertisement

Table of Contents
loading

Related Manuals for SMC Networks Barricade SMC7908VoWBRA2

Summary of Contents for SMC Networks Barricade SMC7908VoWBRA2

  • Page 1: User Guide

    USER GUIDE Barricade™ VoIP SMC7908VoWBRA2 Wireless 4-port VoIP ADSL2/2+ Modem Router...
  • Page 3 Wireless 4-port VoIP ADSL2/2+ Modem Router From SMC’s line of award-winning connectivity solutions 20 Mason Irvine, CA 92618 Phone: (949) 679-8000 April 2007 R01 F/W 0.3 (SIP)
  • Page 4 SMC Networks, Inc. 20 Mason Irvine, CA 92618 All rights reserved. Trademarks: SMC is a registered trademark; and Barricade is a trademark of SMC Networks, Inc. Other product and company names are trademarks or registered trademarks of their respective holders.
  • Page 5 IMITED ARRANTY Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller.
  • Page 6 * SMC will provide warranty service for one year following discontinuance from the active SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans, and cables are covered by a standard one-year warranty from date of purchase. SMC Networks, Inc. 20 Mason Irvine, CA 92618...

  • Page 7: Ec Conformance Declaration

    EC Conformance Declaration SMC contact for these products in Europe is: SMC Networks Europe, Edificio Conata II, Calle Fructuós Gelabert 6-8, 2o, 4a, 08970 - Sant Joan Despí, Barcelona, Spain. Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC).
  • Page 8 OMPLIANCES...

  • Page 9: Table Of Contents

    Introduction ........1-1 About the Barricade ......... 1-1 VoIP (Voice over IP) .
  • Page 10 ABLE OF ONTENTS Configuring the Voice ADSL Router ....4-1 Navigating the Management Interface ......4-2 Making Configuration Changes .
  • Page 11 Troubleshooting ......A-1 Cables ........B-1 Ethernet Cable .
  • Page 12 ABLE OF ONTENTS viii...

  • Page 13: Introduction

    Congratulations on your purchase of the Barricade Router, hereafter referred to as the “Barricade”. We are proud to provide you with a powerful yet simple communication device for connecting your local area network (LAN) to the Internet. For those who want to surf the Internet in the most secure way, this router provides a convenient and powerful solution.

  • Page 14: Features And Benefits

    NTRODUCTION encoding and then compression of the signal into Internet Protocol (IP) packets. The VoIP Router is equipped with a digital signal processor (DSP), which segments the voice signal into frames and stores them in voice packets. These packets are encoded using the industry standard CODECs, G.711, G.723.3 and G.729.

  • Page 15: Applications

    Applications Many advanced networking features are provided by the Barricade: • Wireless and Wired LAN The Barricade provides connectivity to 10/100 Mbps devices, and wireless IEEE 802.11b/g compatible devices, making it easy to create a network in small offices or homes. •...
  • Page 16 NTRODUCTION • DMZ Host Support Allows a networked computer to be fully exposed to the Internet. This function is used when NAT and firewall security prevent an Internet application from functioning correctly. • Security The Barricade supports security features that deny Internet access to specified users, or filter all requests for specific services that the administrator does not want to serve.

  • Page 17: Installation

    Before installing the Barricade have all the items listed under the Package Contents list. If any of the items are missing or damaged, contact your local distributor. Also be sure that you have all the necessary cabling before installing the Barricade. After installing the Barricade, refer to “Configuring the Voice ADSL Router”...

  • Page 18: System Requirements

    NSTALLATION System Requirements To install and connect to the Barricade, you must have: • An ADSL line installed by your ISP. • An ADSL splitter (at least one). • A computer with a CD-ROM drive • Windows 2000 or later, or Mac OS 9.x. •...

  • Page 19: Hardware Description

    ARDWARE ESCRIPTION Hardware Description The Barricade contains an integrated ADSL2+ modem and connects to the Internet or to a remote site using its WAN port. This device can be connected directly to your PC or to a local area network using any of the four Fast Ethernet LAN ports.
  • Page 20 NSTALLATION SMC7908VoWBRA2 contains the following ports on the rear panel: Figure 2-1. SMC7908VoWBRA2 Rear Panel Item ADSL Port LAN Ports Reset Button On/Off Switch Power Inlet Line (FXO) Phone1 and Phone2 (FXS) Description Connect your ADSL line to this port. Fast Ethernet ports (RJ-45).

  • Page 21: Led Indicators

    LED Indicators The power and port LED indicators on the front panel are illustrated in the following figure and table. Figure 2-2. SMC7908VoWBRA2 Front Panel Status Power ADSL Sync Flashing ADSL Flashing Data LAN1-4 (4 LEDs) Flashing WLAN Flashing Description The Barricade is receiving power.

  • Page 22: Isp Settings

    NSTALLATION Status VoIP Phone1/ Phone2 Flashing (2 LEDs) Line Flashing ISP Settings Please collect the following information from your ISP before setting up the Barricade: • ISP account user name and password • VoIP setting details • Protocol, encapsulation and VPI/VCI circuit numbers •...

  • Page 23: Connect The System

    Connect the System The Barricade can be positioned at any convenient location in your office or home. It can also be wall-mounted. No special wiring or cooling requirements are needed. You should, however, comply with the following guidelines: • Keep the Barricade away from any heating devices. •...

  • Page 24: Connect The Power Adapter

    NSTALLATION Warning: Do not plug a phone jack connector into an RJ-45 port. This may damage the Barricade. Note: Use 100-ohm shielded or unshielded twisted-pair cable with RJ-45 connectors for all Ethernet ports. Category 5 cable is recommended. Make sure each twisted-pair cable length does not exceed 100 meters (328 feet).

  • Page 25: Connection Illustration

    ONNECT THE YSTEM Connection Illustration The connection diagram shows how to connect the Barricade.For SMC7908VoWBRA2, please refer to the following diagram. Figure 2-3. SMC7908VoWBRA2 Installation Diagram...
  • Page 26 NSTALLATION 2-10...

  • Page 27: Configuring Client Pc

    HAPTER ONFIGURING LIENT After completing hardware setup by connecting all your network devices, you need to configure your computer to connect to the Barricade. See: “Windows 2000” on page 3-3 “Windows XP” on page 3-6 “Configuring Your Macintosh Computer” on page 3-8 depending on your operating system.

  • Page 28: Tcp/Ip Configuration

    ONFIGURING LIENT TCP/IP Configuration To access the Internet through the Barricade, you must configure the network settings of the computers on your LAN to use the same IP subnet as the Barricade. The default IP settings for the Barricade are: IP Address: 192.168.2.1 Subnet Mask: 255.255.255.0 Note: These settings can be changed to fit your network requirements,...

  • Page 29: Windows 2000

    Windows 2000 1. On the Windows desktop, click Start/Settings/Network and Dial-Up Connections. 2. Click the icon that corresponds to the connection to your Barricade. 3. The connection status screen will open. Click Properties. 4. Double-click Internet Protocol (TCP/IP). 5. If Obtain an IP address automatically and Obtain DNS server address automatically...

  • Page 30: Disable Http Proxy

    ONFIGURING LIENT Disable HTTP Proxy You need to verify that the “HTTP Proxy” feature of your web browser is disabled. This is so that your browser can view the Barricade’s HTML configuration pages. See page 3-6 for details. Obtain IP Settings from Your Barricade Now that you have configured your computer to connect to your Barricade, it needs to obtain new network settings.
  • Page 31 3. Type ipconfig /renew and press the ENTER key. Verify that your IP address is now 192.168.2.xxx, your subnet mask is 255.255.255.0 and your default gateway is 192.168.2.1. These values confirm that your Barricade is functioning. 4. Type exit and press the ENTER key to close the Command Prompt window.

  • Page 32: Windows Xp

    ONFIGURING LIENT Windows XP 1. On the Windows desktop, click Start/Control Panel. 2. In the Control Panel window, click Network and Internet Connections. 3. The Network Connections window will open. Double-click the connection for this device. 4. On the connection status screen, click Properties. 5.

  • Page 33: Obtain Ip Settings From Your Barricade

    Obtain IP Settings from Your Barricade Now that you have configured your computer to connect to your Barricade, it needs to obtain new network settings. By releasing old DHCP IP settings and renewing them with settings from your Barricade, you can verify that you have configured your computer correctly.

  • Page 34: Configuring Your Macintosh Computer

    ONFIGURING LIENT Configuring Your Macintosh Computer You may find that the instructions here do not exactly match your operating system. This is because these steps and screenshots were created using Mac OS 10.2. Mac OS 7.x and above are similar, but may not be identical to Mac OS 10.2.

  • Page 35: Disable Http Proxy

    3. If Using DHCP Server is already selected in the Configure field, your computer is already configured for DHCP. If not, select this option. 4. Your new settings are shown on the TCP/IP tab. Verify that your IP address is now 192.168.2.xxx, your subnet mask is 255.255.255.0 and your default gateway is 192.168.2.1.
  • Page 36 ONFIGURING LIENT 3. Uncheck all check boxes and click OK. 3-10...

  • Page 37: Adsl R Outer

    HAPTER ONFIGURING THE ADSL R OICE OUTER After you have configured TCP/IP on a client computer, you can configure the Barricade using your web browser. To access the Barricade’s management interface, enter the default IP address of the Barricade in your web browser: http://192.168.2.1. Enter the default password: smcadmin, and click LOGIN.

  • Page 38: Configuring The Voice Adsl Router

    ONFIGURING THE OICE Navigating the Management Interface The first screen of the web management is Country Selection. You need to select your country before accessing the management interface. Click OK to confirm your selection. Click Apply to continue. ADSL R OUTER...

  • Page 39: Making Configuration Changes

    The Barricade’s management interface consists of a Setup Wizard and an Advanced Setup section. Setup Wizard: Use the Setup Wizard if you want to quickly set up the Barricade. Go to “SETUP WIZARD” on page 4-4. Advanced Setup: Advanced Setup supports more advanced functions like VoIP, Firewall, IP and MAC address filtering, virtual server setup, virtual DMZ host, as well as other functions.

  • Page 40: Setup Wizard

    ONFIGURING THE OICE SETUP WIZARD Channel and SSID Click on SETUP WIZARD and NEXT, then you will see the Channel and SSID screen. Parameter SSID SSID Broadcast Wireless Mode Channel Click NEXT to continue. ADSL R OUTER Description Service Set ID. The SSID must be the same on the Barricade and all of its wireless clients.

  • Page 41: Adsl Setting

    ADSL Setting Select your Country and Internet Service Provider. This will automatically configure the Barricade with the correct Protocol, Encapsulation and VPI/VCI settings for your ISP. If your Country or Internet Service Provider is not listed in this screen, you will need to manually enter settings. Go to “Parameter Setting - Country or ISP Not Listed”...

  • Page 42: Voip Setting

    ADSL R ONFIGURING THE OICE OUTER VoIP Setting Configure your VoIP account settings on this screen.
  • Page 43 Parameter Telephony Tone Country VoIP Provider Username Password Phone Number Display Name SIP Domain Realm Proxy IP Address Proxy Port Registrar IP Address Registrar Port Primary Codec Click NEXT to continue. Description Select your Country. This will automatically configure the Barricade with the correct telephony tone set for the selected country.

  • Page 44: Confirm

    ONFIGURING THE OICE Confirm The Confirm screen shows a summary of the configuration parameters. Check ADSL operation mode (WAN), Network Layer Parameters (WAN), ISP parameters and VoIP settings are correct. ADSL R OUTER...
  • Page 45 Parameter Description Wireless Parameters SSID The SSID must be the same on the Barricade and all of its wireless clients. SSID Broadcast The status of enabling or disabling the broadcasting of the SSID. Wireless Mode This device supports both 11g and 11b wireless networks. Channel This channel must be the same on the Barricade and all of its wireless clients.

  • Page 46: Parameter Setting - Country Or Isp Not Listed

    ONFIGURING THE OICE If the parameters are correct, click FINISH to save these settings. Your Barricade is now set up. Go to “Troubleshooting” if you cannot make a connection to the Internet. Parameter Setting - Country or ISP Not Listed If your Country or Internet Service Provider is not listed, select Others.
  • Page 47 PPPoE Parameter VPI/VCI Encapsulation Username Password Confirm Password Click NEXT to continue to the “Confirm” settings screen. Go to “Confirm” on page 4-8 in the manual for details about the settings. Description Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP.
  • Page 48 ONFIGURING THE OICE PPPoA Parameter VPI/VCI Encapsulation Username Password Confirm Password Click NEXT to continue to the “Confirm” settings page. Go to “Confirm” on page 4-8 in the manual for details about the settings. 4-12 ADSL R OUTER Description Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP.
  • Page 49 1483 Bridging (DHCP) Parameter DNS Server VPI/VCI Encapsulation Click NEXT to continue to the “Confirm” settings page. Go to “Confirm” on page 4-8 in the manual for details about the setting. Description Enter the DNS Server IP address provided by your ISP.
  • Page 50 ONFIGURING THE OICE 1483 Bridging (Static) Parameter IP Address Subnet Mask Default Gateway DNS Server VPI/VCI Encapsulation Click NEXT to continue to the “Confirm” settings page. Go to “Confirm” on page 4-8 in the manual for details about the settings. 4-14 ADSL R OUTER...
  • Page 51 1483 Routing Parameter IP Address Subnet Mask Default Gateway DNS Server VPI/VCI Encapsulation Click NEXT to continue to the “Confirm” settings page. Go to “Confirm” on page 4-8 in the manual for details about the settings. Description Enter the IP address provided by your ISP. Enter the subnet mask address provided by your ISP.
  • Page 52 ONFIGURING THE OICE Bridging Enter the Bridging settings provided by your ISP. Parameter Management IP Address VPI/VCI Encapsulation Click NEXT to continue to the “Confirm” settings page. Go to “Confirm” on page 4-8 in the manual for details about the settings. 4-16 ADSL R OUTER...

  • Page 53: Advanced Setup

    Advanced Setup The left-hand side displays the main menu and the right-hand side shows descriptive information. The advanced management interface contains 16 main menu items as described in the following table. Menu Description System Sets the local time zone, the password for administrator access, and the IP address of a PC that will be allowed to manage the Barricade remotely.
  • Page 54 ONFIGURING THE OICE Menu Description Tools Contains options to backup & restore the current configuration, restore all configuration settings to the factory defaults, update system firmware, or reset the system. Status Provides WAN connection type and status, firmware and hardware version numbers, system IP settings, as well as DHCP, NAT, and firewall information.

  • Page 55: System

    DVANCED ETUP SYSTEM Time Settings Select your local time zone from the drop-down list. This information is used for log entries and client filtering. For accurate timing of log entries and system events, you need to set the time zone. Select your time zone from the drop-down list. If daylight savings is used in your area, check the box to enable the function, and select the start/end dates.
  • Page 56 ONFIGURING THE OICE Password Settings Use this screen to change the password for accessing the management interface. Passwords can contain from 3~12 alphanumeric characters and are case sensitive. Note: If you lost the password, or you cannot gain access to the user interface, press the blue reset button on the rear panel, holding it down for at least 10 seconds to restore the factory defaults.

  • Page 57: Remote Management

    DVANCED ETUP Remote Management By default, management access is only available to users on your local network. However, you can also manage the Barricade from a remote host by entering the IP address of a remote computer on this screen. Check the Enabled check box, and enter the IP address of the Host Address and click Save Settings.

  • Page 58: Wan

    ONFIGURING THE OICE Specify the WAN connection parameters provided by your Internet Service Provider (ISP). The Barricade supports the following modes: • ATM PVC • Clone MAC • ATM PVC To configure your Internet Connection settings, select ATM PVC, then VC1.
  • Page 59 Parameter Description VC1 to VC8 Click on the desired VC to configure the connection parameters. VPI/VCI Displays the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) configured for the corresponding VC. Encapsulation Displays the Encapsulation configured for the corresponding VC.

  • Page 60: Atm Interface

    ONFIGURING THE OICE ATM Interface 1483 Bridging Enter the settings provided by your ISP. In Bridging mode the Barricade will act as a Bridge passing the IP addressing directly to the attached client PC. Parameter VPI/VCI Encapsulation QoS Class PCR/SCR/MBS 4-24 ADSL R OUTER...
  • Page 61 PPPoA Parameter VPI/VCI Encapsulation QoS Class PCR/SCR/MBS IP assigned by ISP IP Address Subnet Mask Connect Type Idle Time (Minute) Username Password Description Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP. Select the encapsulation used by ISP from the drop-down list.
  • Page 62 ONFIGURING THE OICE Parameter Confirm Password 1483 Routing Parameter IP Address Subnet Mask Default Gateway VPI/VCI Encapsulation QoS Class PCR/SCR/MBS DHCP Client 4-26 ADSL R OUTER Description Confirm password Leave the Maximum Transmission Unit (MTU) at the default value (1500) unless you have a particular reason to change it.
  • Page 63 PPPoE Parameter IP Address Subnet Mask VPI/VCI Encapsulation QoS Class PCR/SCR/MBS Connect Type Idle Time (Minute) Username Password Confirm Password Description Enter the IP address provided by your ISP. Enter the subnet mask address provided by your ISP. Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP.
  • Page 64 ONFIGURING THE OICE MAC Encapsulated Routing Parameter IP Address Subnet Mask Default Gateway VPI/VCI Encapsulation QoS Class PCR/SCR/MBS DHCP Client 4-28 ADSL R OUTER Description Enter the IP address provided by your ISP. Enter the subnet mask address provided by your ISP. Enter the gateway address provided by your ISP.
  • Page 65 DVANCED ETUP Clone MAC Address Some ISPs require you to register your MAC address with them. If this is the case, and you have previously registered the MAC address of another device, the MAC address of the Barricade must be changed to the MAC address that you have registered with your ISP.
  • Page 66 ONFIGURING THE OICE A Domain Name Server (DNS) is an index of IP addresses and Web addresses. If you type a web address into your browser, such as www.smc.com, a DNS server will find that name in its index and find the matching IP address: xxx.xxx.xxx.xxx.

  • Page 67: Lan

    DVANCED ETUP The LAN settings menu allows you to change the default IP address of the Barricade, modify the DHCP server settings and create VLAN’s. 4-31...
  • Page 68 ONFIGURING THE OICE Parameter LAN IP IP Address IP Subnet Mask The subnet mask of the Barricade. DHCP Server VLAN Binding LAN1 to LAN4 This option allows you to change VLAN membership of LAN DHCP Server DHCP Server Lease Time 4-32 ADSL R OUTER...
  • Page 69 Parameter Description IP Address Pool Start IP Address Specify the start IP address of the DHCP pool. Do not include the gateway address of the Barricade in the client address pool. If you change the pool range, make sure the first three octets match the gateway’s IP address, i.e., 192.168.2.xxx.
  • Page 70 ONFIGURING THE OICE VLAN Profile Configure the VLAN settings in this screen. • Description: Enter a description for the VLAN group, for example: Admin PC’s • IP Address: Enter IP address for the VLAN. • Subnet Mask: Enter Subnet Mask address for the VLAN. •...

  • Page 71: Wireless

    DVANCED ETUP WIRELESS The Barricade also operates as a wireless access point, allowing wireless computers to communicate with each other. To configure this function, all you need to do is enable the wireless function, define the radio channel, the SSID, and the security options. Check Enable and click SAVE SETTINGS.
  • Page 72 ONFIGURING THE OICE Channel and SSID You must specify a common radio channel and SSID (Service Set ID) to be used by the Barricade and all of its wireless clients. Be sure you configure all of its clients to the same values. Parameter SSID SSID Broadcast...
  • Page 73 DVANCED ETUP Access Control Using the Access Control functionality, you can restrict access based on MAC address. Each PC has a unique identifier known as a Medium Access Control (MAC) address. With MAC filtering enabled, the computers whose MAC address you have listed in the filtering table will be able to connect (or will be denied access) to the Barricade.
  • Page 74 ONFIGURING THE OICE Security To make your wireless network safe, you should turn on the security function. The Barricade supports the following security mechanism: • WPA/WPA2 • WPA2 Only • WPA Only • 4-38 ADSL R OUTER...
  • Page 75 WPA/WPA2 Wi-Fi Protected Access (WPA) combines temporal key integrity protocol (TKIP) and 802.1x mechanisms. It provides dynamic key encryption and 802.1x authentication service. Wi-Fi Protected Access 2 (WPA2) is a product certification that is available through the Wi-Fi Alliance. WPA2 certifies that wireless equipment is compatible with the IEEE 802.11i standard.
  • Page 76 ONFIGURING THE OICE WPA2 Only WPA2 is a product certification that is available through the Wi-Fi Alliance. WPA2 certifies that wireless equipment is compatible with the IEEE 802.11i standard. The WPA2 product certification formally replaces Wired Equivalent Privacy (WEP) and the other security features of the original IEEE 802.11 standard.
  • Page 77 WPA Only Wi-Fi Protected Access (WPA) combines temporal key integrity protocol (TKIP) and 802.1x mechanisms. It provides dynamic key encryption and 802.1x authentication service. Parameter Authentication Choose 802.1X or Pre-shared Key to use as the authentication method. • 802.1X: for the enterprise network with a RADIUS server. •...
  • Page 78 ONFIGURING THE OICE 802.1X If 802.1x is used in your network, then you should enable this function for the Barricade. Parameter Authentication Session Idle timeout Re-Authentication Period Quiet Period Server IP Server Port Secret Key NAS-ID 4-42 ADSL R OUTER Description Choose 802.1X authentication option.
  • Page 79 If you want to use WEP to protect your wireless network, you need to set the same parameters for the Barricade and all your wireless clients. Parameter WEP Mode Select 64 bit or 128 bit key to use for encryption. Key Entry Method Select Hex or ASCII to use for encryption key.
  • Page 80 ONFIGURING THE OICE To manually configure the encryption key, enter five hexadecimal pairs of digits for the 64-bit key, or enter 13 pairs for the 128-bit key. (A hexadecimal digit is a number or letter in the range 0-9 or A-F.) Note: WEP protects data transmitted between wireless nodes, but does not protect any transmissions over your wired network or over the Internet.

  • Page 81: Nat

    DVANCED ETUP Network Address Translation allows multiple users to access the Internet sharing one public IP. 4-45...

  • Page 82: Address Mapping

    ONFIGURING THE OICE Address Mapping Allows one or more public IP addresses to be shared by multiple internal users. This also hides the internal network for increased privacy and security. Enter the Public IP address you wish to share into the Global IP field.
  • Page 83 DVANCED ETUP Virtual Server If you configure the Barricade as a virtual server, remote users accessing services such as web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP addresses.
  • Page 84 ONFIGURING THE OICE Special Application Some applications require multiple connections, such as Internet gaming, video-conferencing, and Internet telephony. These applications may not work when Network Address Translation (NAT) is enabled. If you need to run applications that require multiple connections, use these screens to specify the additional public ports to be opened for each application.

  • Page 85: Nat Mapping Table

    NAT Mapping Table This screen displays the current NAPT (Network Address Port Translation) address mappings. NAT Mapping Table displays the current NAPT address mappings. The NAT address mappings are listed 20 lines per page, click the control buttons to move forwards and backwards. As the NAT mapping is dynamic, a Refresh button is provided to refresh the NAT Mapping Table with the mots updated values.

  • Page 86: Route

    ONFIGURING THE OICE ROUTE These screens define routing related parameters, including static routes and RIP (Routing Information Protocol) parameters. Static Route Parameter Index Network Address Subnet Mask Gateway Click Add to add a new static route to the list, or check the box of an already entered route and click Modify.
  • Page 87 Parameter General RIP Parameters RIP mode Auto summary Table of current Interface RIP parameter Interface Operation Mode Version Description Globally enables or disables RIP. If Auto summary is disabled, then RIP packets will include sub-network information from all sub-networks connected to the router. If enabled, this sub-network information will be summarized to one piece of information covering all sub-networks.
  • Page 88 ONFIGURING THE OICE Parameter Poison Reverse Authentication Required Authentication Code RIP sends routing-update messages at regular intervals and when the network topology changes. When a router receives a routing update that includes changes to an entry, it updates its routing table to reflect the new route.

  • Page 89: Routing Table

    Routing Table Parameter Description Flags Indicates the route status: C = Direct connection on the same subnet. S = Static route. R = RIP (Routing Information Protocol) assigned route. I = ICMP (Internet Control Message Protocol) Redirect route. Network Address Destination IP address. Netmask The subnetwork associated with the destination.

  • Page 90: Firewall

    ONFIGURING THE OICE FIREWALL The Barricade Router’s firewall inspects packets at the application layer, maintains TCP and UDP session information including time-outs and the number of active sessions, and provides the ability to detect and prevent certain types of network attacks. Network attacks that deny access to a network device are called Denial-of-Service (DoS) attacks.
  • Page 91 Access Control Access Control allows users to define the outgoing traffic permitted or not-permitted through the WAN interface. The default is to permit all outgoing traffic. The following items are on the Access Control screen: Parameter Enable Filtering Function Normal Filtering Table Displays descriptive list of Filtering rules defined. Description Enable or Disable Access control function.
  • Page 92 ONFIGURING THE OICE To create a new access control rule: 1. Click Add PC on the Access Control screen. The Access Control Add PC screen will appear. 2. Define the appropriate settings for client PC services. 3. Click OK and then click SAVE SETTINGS to save your settings. 4-56 ADSL R OUTER...

  • Page 93: Mac Filter

    DVANCED ETUP MAC Filter The MAC Filter allows you to define what client PC’s can access the Internet. When enabled only the MAC addresses defined in the MAC Filtering table will have access to the Internet. All other client devices will be denied access.

  • Page 94: Url Blocking

    ONFIGURING THE OICE URL Blocking The Barricade allows the user to block access to web sites by entering either a full URL address or just a keyword. This feature can be used to protect children from accessing violent or pornographic web sites. You can define up to 30 sites here.
  • Page 95 DVANCED ETUP Schedule Rule You may filter Internet access for local clients based on rules. Each access control rule may be activated at a scheduled time. Define the schedule on the Schedule Rule screen, and apply the rule on the Access Control screen. 4-59...
  • Page 96 ONFIGURING THE OICE Follow these steps to add a schedule rule: 1. Click Add Schedule Rule on the Schedule Rule screen. The Edit Schedule Rule screen will appear. 2. Define the appropriate settings for a schedule rule. 3. Click OK and then click SAVE SETTINGS to save your settings. 4-60 ADSL R OUTER...

  • Page 97: Intrusion Detection

    DVANCED ETUP Intrusion Detection • Intrusion Detection Feature Stateful Packet Inspection (SPI) and Anti-DoS firewall protection (Default: Enabled) — The Intrusion Detection Feature of the Barricade Router limits access for incoming traffic at the WAN port. When the SPI feature is turned on, all incoming packets will be blocked except for those types marked in the Stateful Packet Inspection section.
  • Page 98 ADSL R ONFIGURING THE OICE OUTER 4-62...
  • Page 99 • Stateful Packet Inspection This is called a “stateful” packet inspection because it examines the contents of the packet to determine the state of the communications; i.e., it ensures that the stated destination computer has previously requested the current communication. This is a way of ensuring that all communications are initiated by the recipient computer and are taking place only with sources that are known and trusted from previous interactions.
  • Page 100 ONFIGURING THE OICE • Connection Policy Enter the appropriate values for TCP/UDP sessions as described in the following table. Parameter Fragmentation half-open wait TCP SYN wait TCP FIN wait TCP connection idle timeout UDP session idle timeout H.323 data channel idle timeout 4-64 ADSL R...
  • Page 101 • DoS Criteria and Port Scan Criteria Set up DoS and port scan criteria in the spaces provided (as shown below). Parameter Defaults Total incomplete TCP/UDP sessions sessions HIGH Total incomplete sessions TCP/UDP sessions Incomplete sessions TCP/UDP sessions (per min) HIGH Incomplete sessions TCP/UDP sessions...
  • Page 102 ONFIGURING THE OICE If you have a client PC that cannot run an Internet application properly from behind the firewall, you can open the client up to unrestricted two-way Internet access. Enter the IP address of a DMZ (Demilitarized Zone) host on this screen. Adding a client to the DMZ may expose your local network to a variety of security risks, so only use this option as a last resort.

  • Page 103: Snmp

    DVANCED ETUP SNMP Use the SNMP configuration screen to display and modify parameters for the Simple Network Management Protocol (SNMP). 4-67...
  • Page 104 ONFIGURING THE OICE Community A computer attached to the network, called a Network Management Station (NMS), can be used to access this information. Access rights to the agent are controlled by community strings. To communicate with the Barricade, the NMS must first submit a valid community string for authentication.
  • Page 105 Trap Specify the IP address of the NMS to notify when a significant event is detected by the agent. When a trap condition occurs, the SNMP agent sends an SNMP trap message to any NMS specified as a trap receiver. Parameter Description IP Address Traps are sent to this address when errors or specific events occur on...

  • Page 106: Adsl

    ONFIGURING THE OICE ADSL ADSL (Asymmetric Digital Subscriber Line) is designed to deliver more bandwidth downstream (from the central office to the customer site) than upstream. This section is used to configure the ADSL operation type and shows the ADSL status. ADSL Parameters This screen is designed for the engineer to test the ADSL loop condition.
  • Page 107 DVANCED ETUP ADSL Status The Status screen displays information on connection line status, data rate, operation data and defect indication, and statistics. 4-71...
  • Page 108 ONFIGURING THE OICE The following items are included on this information screen: Parameter Status Line Status Data Rate Upstream Downstream Operation Data/Defect Indication Noise Margin Output Power Attenuation Fast Path FEC Correction Interleaved Path FEC Correction Fast Path CRC Error Interleaved Path CRC Error Loss of Signal Defect...

  • Page 109: Voip

    VoIP Voice over Internet Protocol (VoIP) is the routing of voice conversations over the Internet or any other IP-based network. The voice data flows over a general-purpose packet-switched network, instead of traditional dedicated, circuit-switched voice transmission lines. VoIP Account Configure your VoIP account settings on this screen. Before you begin you will need to obtain the following settings from your service provider: •...
  • Page 110 ONFIGURING THE OICE • Select the account form the Account Profile drop-down menu. To set-up a second VoIP account, select Account 2. Up to 4 accounts can be configured. • Check the Activated check box to enable the account. If the box is unchecked the account is disabled.
  • Page 111 • Input the SIP Domain, Realm, Proxy Address, Proxy Port, Registrar Address and Registrar Port. If your VoIP provider was listed and selected, these settings should already be configured. • Use the Up and Down buttons to change Codec priority. The preferred Codec goes at the top.
  • Page 112 ONFIGURING THE OICE Parameter Support User-Agent Header Support Out of Band DTMF Check this box to enable support for Out of Band Call Hold Version Codec’s are used to convert an analogue voice signal to digitally encoded version. Codec’s vary in the sound quality, the bandwidth required, the computational requirements, etc.
  • Page 113 VoIP Extensions You can configure the Line and Phone port settings on this screen. Parameter Telephony Tone Country Setting Extension Number Additional Number: Description Configures telephony tone set for the selected country. Select Extension Number to assign to the phone. This should be your VoIP phone number.
  • Page 114 ONFIGURING THE OICE Parameter For the following 4 items, check the box to enable the function: • Answer calls for all numbers Check this box to answer all incoming calls. • Call Waiting • Caller-ID Presentation • Different dial tone for VoIP Enabling this function gives a different dial Telephony Hook Flash Timer 4-78 ADSL R...

  • Page 115: Sip Setting

    SIP Setting The following SIP related parameters are configurable. Parameter SIP Parameters SIP Listen Port Codec Rate(G723, G729, G711) Description This option allows you to change the default SIP Listen Port. The default setting is 5060. It is recommended to leave this value unchanged. You can select the desired Codec rate.
  • Page 116 ONFIGURING THE OICE Port Advanced Setting There are 11 advanced functions that can be configured in this screen. • Volume Gain Control: Two modes are available. The fixed gain control means the device is supported to supply a constant level of amplification.
  • Page 117 • PLC (Packet Loss Compensation): During the transmission of a series of packets, if one of them is lost, then the device will use the mathematical algorithm to calculate a value to make up the lost packet. This function is designed to make the voice conversation more smooth.
  • Page 118 ONFIGURING THE OICE Parameter Volume Gain Control Jitter Buffer Mode Jitter Buffer Delay Echo Canceller Delay Caller ID Mode Inter Digit Delay Additional Ringing Mode T.38 Mode 4-82 ADSL R OUTER Description It is recommended leaving these four settings at the default value.

  • Page 119: Dialing Plans

    Dialing plans Dialing plans allow you to define the connection type used when a specified number is dialed. For example you may want numbers beginning “0800” to dial out over PSTN. Alternatively you may want numbers beginning “012” to dial out over the Internet (VoIP). Also you may want to block certain numbers from being dialed.
  • Page 120 ONFIGURING THE OICE To set-up a dialing plan, take the following steps: 1. In the Phone number column enter a specific phone number, or the starting digits of a phone number that you want to create a dialing plan for. Example: If you enter “012”...

  • Page 121: Quick Dialing Plans

    Quick Dialing Plans This function allows you to configure up to 20 quick dialing plans. This is done by assigning a quick dial code for a specified phone number. • Quick Dial Code: Enter quick dial code in the range of 01 to 20. To call the phone number associated with the quick dial code you would need to dial *7[Quick Dial Code]# .
  • Page 122 ONFIGURING THE OICE The following example shows how to set up a quick dialing plan for Frank who has the phone number 6194621719: 1. Select the vanity keypad style from the pull-down menu. 2. Enter the number “01” for the Quick Dial Code. 3.
  • Page 123 VoIP Status and Call logs This page displays the VoIP registration status for accounts 1 - 4 and the call logs. Parameter Account SIP URL Registration Received Call Dialed Call Missed Call Rejected Call Forwared Call Click the Refresh button to update the status and log. Description SIP accounts 1 to 4.

  • Page 124: Upnp

    ONFIGURING THE OICE UPnP The Universal Plug and Play architecture offers pervasive peer-to-peer network connectivity of PCs of all form factors, intelligent appliances, and wireless devices. UPnP enables seamless proximity network in addition to control and data transfer among networked devices in the office, home and everywhere within your network.

  • Page 125: Qos

    The QoS (Quality of Service) function allows you to differentiate VoIP traffic and provide it with high-priority forwarding service. In addition, you can specify the outgoing VC of VoIP packets to further guarantee the voice quality. Parameter Enable or disable QoS module function AF1x AF2x...

  • Page 126: Traffic Mapping

    ONFIGURING THE OICE • Assured forwarding, defined in RFC 2597 • Expedited forwarding, defined in RFC 2598 Traffic Mapping Use this screen to classify traffic into Diffserv forwarding groups and outgoing VCs. 4-90 ADSL R OUTER...
  • Page 127 DVANCED ETUP To create a new traffic class: 1. Click ADD TRAFFIC CLASS on the Edit Traffic Class screen. 2. Define the appropriate settings for traffic class. 3. Click SAVE SETTINGS to save your settings. 4-91...
  • Page 128 ONFIGURING THE OICE Traffic Statistics This screen shows the WAN outbound traffic statistics of all the Diffserv forwarding groups in the last 12 hours. 4-92 ADSL R OUTER...

  • Page 129: Ddns

    DVANCED ETUP DDNS Dynamic Domain Name Service (DDNS) provides users on the Internet with a method to tie their domain name to a computer or server. DDNS allows your domain name to follow your IP address automatically by having your DNS records changed when your IP address changes. This DNS feature is powered by DynDNS.org or TZO.com.

  • Page 130: Tools

    ONFIGURING THE OICE TOOLS Use the Tools menu to backup the current configuration, restore a previously saved configuration, update firmware, and reset the Barricade. Ping Utility This tool allows you to test your network connection. You can specify a domain name or a valid IP address of the remote host for ping test. 4-94 ADSL R OUTER...
  • Page 131 Configuration Tools Choose a function and click Next. • Backup Router Configuration: this allows you to save the Barricade’s configuration to a file. • Restore from saved Configuration file: this function is used to restore the previously saved backup configuration file. •...
  • Page 132 ONFIGURING THE OICE Firmware Upgrade Use this screen to update the firmware or user interface to the latest versions. 1. Download the upgrade file from the SMC web site first, and save it to your hard drive. 2. Then click Browse... to look for the downloaded file. Click BEGIN UPGRADE.
  • Page 133 Reset Click REBOOT ROUTER to reset the Barricade. The reset will be complete when the power LED stops blinking. If you perform a reset from this screen, the configurations will not be changed back to the factory default settings. Note: If you use the Reset button on the back panel, the Barricade performs a power reset.

  • Page 134: Status

    ONFIGURING THE OICE STATUS The Status screen displays WAN/LAN connection status, firmware, and hardware version numbers, illegal attempts to access your network, as well as information on DHCP clients connected to your network. The security log may be saved to a file by clicking Save and choosing a location. Scroll down to view more information on the Status screen.
  • Page 135 The following items are included on the Status screen: Parameter Description INTERNET Displays WAN connection type and status. Release Click on this button to disconnect from the WAN. Renew Click on this button to establish a connection to the WAN. GATEWAY Displays system IP settings, as well as DHCP Server and Firewall status.

  • Page 136: Finding The Mac Address Of A Network Card

    ONFIGURING THE OICE Finding the MAC address of a Network Card WINDOWS NT4/2000/XP Click Start/Programs/Command Prompt. Type “ipconfig /all” and press “ENTER”. The MAC address is listed as the “Physical Address.” MACINTOSH Click System Preferences/Network. The MAC address is listed as the “Ethernet Address” on the TCP/IP tab. LINUX Run the command “/sbin/ifconfig.”...
  • Page 137 This section describes common problems you may encounter and possible solutions to them. The Barricade can be easily monitored through panel indicators to identify problems. Troubleshooting Chart Symptom Action LED Indicators Power LED is • • PPENDIX ROUBLESHOOTING Check connections between the Barricade, the external power supply, and the wall outlet.

  • Page 138: Troubleshooting

    ROUBLESHOOTING Troubleshooting Chart Symptom LED Indicators Link LED is Off Network Connection Problems Cannot ping the Barricade from the attached Action • Verify that the Barricade and attached device are powered on. • Be sure the cable is plugged into both the Barricade and the corresponding device.
  • Page 139 Troubleshooting Chart Symptom Action Management Problems Cannot connect • using the web browser • • Forgot or lost • the password Be sure to have configured the Barricade with a valid IP address, subnet mask, and default gateway. Check that you have a valid network connection to the Barricade and that the port you are using has not been disabled.
  • Page 140 ROUBLESHOOTING Troubleshooting Chart Symptom Wireless Problems A wireless PC cannot associate with the Barricade. The wireless network is often interrupted. The Barricade cannot be detected by a wireless client. Action • Make sure the wireless PC has the same SSID settings as the Barricade.
  • Page 141 Ethernet Cable Caution: DO NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards. Specifications Cable 10BASE-T 100BASE-TX Cat. 5 100-ohm UTP Wiring Conventions For Ethernet connections, a twisted-pair cable must have two pairs of wires.

  • Page 142: Cables

    ABLES Each wire pair must be attached to the RJ-45 connectors in a specific orientation. The following figure illustrates how the pins on an Ethernet RJ-45 connector are numbered. Be sure to hold the connectors in the same orientation when attaching the wires to the pins. Figure B-1.

  • Page 143: Ethernet Cable

    Pin Assignments With 100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 for receiving data. RJ-45 Pin Assignments Pin Number 1: The “+” and “-” signs represent the polarity of the wires that make up each wire pair. Straight-Through Wiring If the port on the attached device has internal crossover wiring (MDI-X), then use straight-through cable.
  • Page 144 ABLES Crossover Wiring If the port on the attached device has straight-through wiring (MDI), use crossover cable. Crossover Cable Pin Assignments End 1 1 (Tx+) 2 (Tx-) 3 (Rx+) 6 (Rx-) End 2 3 (Rx+) 6 (Rx-) 1 (Tx+) 2 (Tx-)

  • Page 145: Adsl Cable

    ADSL Cable Use standard telephone cable to connect the RJ-11 telephone wall outlet to the RJ-45 ADSL port on the ADSL Router. Caution: Do not plug a phone jack connector into an RJ-45 port. Specifications Cable ADSL Line Wiring Conventions For ADSL connections, a cable requires one pair of wires.
  • Page 146 ABLES R1 T1 1 2 3 4 5 6 6x2 Jack Signal Name Not used Line 2 Tip Line 1 Ring Line 1 Tip Line 2 Ring Not used Figure B-3. RJ-11 Pinouts R1 T1 R2 1 2 3 4 5 6 1 2 3 4 5 6 6x4 Jack T = Tip...

  • Page 147: Specifications

    Physical Characteristics Ports Four 10/100Mbps RJ-45 ports One ADSL RJ-11 port Two Phone ports One Line port ADSL Features Supports DMT line modulation Supports Annex A Full-Rate ADSL: up to 8 Mbps downstream, up to 1 Mbps upstream (G.992.1 &T1.413, Issue 2) and ADSL2 (G.992.3) and ADSl2+ (G.992.5) Supports G.Lite ADSL: up to 1.5 Mbps downstream, up to 512 Kbps upstream...

  • Page 148: Specifications

    PECIFICATIONS Security Features Password protected configuration access User authentication (PAP/CHAP) with PPP Firewall NAT NAPT VPN pass through (IPSec-ESP Tunnel mode,L2TP, PPTP) LAN Features IEEE 802.1D (self-learning transparent Bridging) DHCP Server DNS Proxy Static Routing, RIPv1 and RIP VoIP Features Codec - G.711, G.723, G.729a, G.168 Modulation Type OFDM, CCK...
  • Page 149 PECIFICATIONS Operating Channels IEEE 802.11b compliant: 11 channels (US, Canada) 13 channels (ETSI) 2 Channels (Spain) 4 Channels (France) 14 channels (Japan) Operating Channels IEEE 802.11g compliant: 13 channels (US, Canada, Europe, Japan) RF Output Power Modulation Rate-Output Power (dBm) 802.11b - 1Mbps 16 802.11b - 2Mbps 16 802.11b - 5.5Mbps 16...
  • Page 150 PECIFICATIONS Modulation Rate-Receiver Sensitivity Typical (dBm) 802.11g - 6Mbps -88 802.11g - 9Mbps -87 802.11g - 12Mbps -84 802.11g - 18Mbps -82 802.11g - 24Mbps -79 802.11g - 36Mbps -75 802.11g - 48Mbps -68 802.11g - 54Mbps -68 Temperature: IEC 68-2-14 0 to 50 degrees C (Standard Operating) -40 to 70 degree C (Non-operation) Humidity...
  • Page 151 SMC7908VoWBRA2 TECHNICAL SUPPORT From U.S.A. and Canada (24 hours a day, 7 days a week) Phn: 800-SMC-4-YOU / 949-679-8000 Fax: 949-502-3400 ENGLISH Technical Support information available at www.smc.com FRENCH Informations Support Technique sur www.smc.com DEUTSCH Technischer Support und weitere Information unter www.smc.com SPANISH En www.smc.com Ud.

This manual is also suitable for:

7908vowbra2

Table of Contents