Specifications - Makita KP0810 Instruction Manual

ENGLISH (Original instructions)
1-1. Knob
1-2. Pointer
2-1. Lock button / Lock-off button
2-2. Switch trigger
3-1. Planer blade
3-2. Rear base
3-3. Foot
4-1. Socket wrench
5-1. Bolts
5-2. Drum
5-3. Planer blade
5-4. Drum cover
5-5. Adjusting plate
6-1. Inside edge of gauge plate
6-2. Blade edge
6-3. Planer blade
6-4. Adjusting plate
6-5. Screws
6-6. Heel
6-7. Back side of gauge base
6-8. Gauge plate
6-9. Gauge base
7-1. Socket wrench
8-1. Pan head screw
8-2. Adjusting plate
8-3. Planer blade locating lugs

SPECIFICATIONS

Shiplapping depth
No load speed (min
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for planing wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
Noise
The typical A-weighted noise level determined according
to EN60745:
Explanation of general view
8-4. Gauge plate
8-5. Heel of adjusting plate
8-6. Set plate
8-7. Inside flank of gauge plate
8-8. Gauge base
8-9. Back side of gauge base
8-10. Mini planer blade
9-1. Mini planer blade
9-2. Groove
9-3. Set plate
9-4. Hex. flange head bolts
9-5. Drum cover
9-6. Drum
9-7. Adjusting plate
10-1. Stopper
10-2. Chip discharge opening
11-1. Recessed part
11-2. Protrusion
12-1. Dust bag
12-2. Chip discharge opening
13-1. Fastener
14-1. Vacuum cleaner
15-1. Elbow
16-1. Start
16-2. End
18-1. Blade edge
Model
Planing width
Planing depth
-1
)
Overall length
Net weight
Safety class
KP0810
16,000
3.3 kg
ENE001-1
Model KP0810
Sound pressure level (L
ENF002-2
Sound power level (L
Uncertainty (K) : 3 dB(A)
Model KP0810C
Sound pressure level (L
Sound power level (L
ENG905-1
Uncertainty (K) : 3 dB(A)
5
18-2. Cutting line
18-3. Depth guide
19-1. Screw (A)
19-2. Screw (B)
19-3. Edge fence
23-1. V groove (medium amount of
chamfering)
23-2. V groove (small amount of
chamfering)
23-3. V groove (great amount of
chamfering)
24-1. Chamfering rule
24-2. Screws
25-1. Edge of chamfering rule
26-1. Sharpening holder
27-1. Wing nut
27-2. Blade (A)
27-3. Blade (B)
27-4. Side (D)
27-5. Side (C)
29-1. Limit mark
30-1. Screwdriver
30-2. Rear cover
31-1. Carbon brushes
KP0810C
82 mm
4 mm
25 mm
12,000
290 mm
3.4 kg
/II
) : 88 dB(A)
pA
) : 99 dB(A)
WA
) : 82 dB(A)
pA
) : 93 dB(A)
WA
Wear ear protection