After Replacing The H And L Needles; After Replacing Only The L Needle - Husqvarna 322 Workshop Manual

Brush cutters, trimmers, pruners, hedge trimmers
Table of Contents

Advertisement

3

After replacing the H and L needles

1. Remove the plastic sleeves from both needles and screw
out the needles.
2. Carefully screw the new needles in until they bottom.
Screw out the L needle 1 turn.
Screw out the H needle 2 1/2 turns.
3. Press the new plastic sleeves on the needles until the first
stop. The sleeves can still be turned without the needles
turning.
4. Turn the plastic sleeve on the L needle as far as possible
clockwise (leanest fuel mixture).
5. Start the engine and let it idle.
6. Use the screwdriver 531 00 48-63 to adjust the L needle.
The blade is 2 mm wide and goes through the plastic
sleeve and only adjusts the needle.
Adjust the L needle so that the highest idling speed is
obtained.
Use the tachometer 502 71 14-01 to check the speed.
7. Check that the plastic sleeve on the L needle is still turned
as far as possible clockwise (leanest fuel mixture).
531 00 48-63
8. Press the plastic sleeve on the L needle using a punch
(Ø 5 mm).
Now turn the L needle as far as possible anticlockwise
(richest fuel mixture).
9. Turn the plastic sleeve on the H needle as far as possible
anticlockwise (richest fuel mixture).
10. Fit four trimmer cords Ø 3.3 mm on a Trimmy Fix M10,
531 00 38-69 for models 322L, 322R, 325L, 325L-X, 325R-X.
Maybe the hole needs to be enlarged a little to make fitting
the trimmer cords easier.
11. Cut the trimmer cord to the right length (measure the length
to the edge of the Trimmy Fix).
Model 322L/R, 325L/L-X/R-X: 142 mm
Fit the Trimmy Fix on the machine.
Model 322C should be used with Trimmy Hit VI and its
standard cord (Ø 2.0 mm). Cut the cord ends so that they
are 146 mm long.
12. Start the engine. Adjust the idling speed T screw if neces-
sary.
13. Use screwdriver 531 00 48-63 to adjust the H needle. The
blade is 2 mm wide and goes through the plastic sleeve
and only adjusts the needle.
Adjust the H needle so that the max. speed 8400 ± 200 r/min
is set.
Use the tachometer 502 71 14-01 to check the speed.
(Does not apply to model 225H60/H75).
14. Run the engine warm for 2–3 minutes.
15. Check that the max speed is still 8400 ± 200 r/min. Adjust
the H needle if necessary.
16. Check that the plastic sleeve on the H needle is still turned
anticlockwise as far as possible (richest fuel mixture).
17. Press in the plastic sleeve using a punch (Ø 5 mm).
18
Fuel system
The basic setting of the carburettor is now complete. Further
fine adjustment, within the limits that the plastic sleeves on the
needles permit, can be necessary.

After replacing only the L needle

1. Turn the H needle as far as possible clockwise (leanest fuel
2. Remove the plastic sleeve on the L needle and unscrew the
3. Carefully screw in the new L needle to the bottom and then
4. Press a new plastic sleeve on the L needle down to the first
5. Turn the plastic sleeve as far as possible clockwise (leanest
6. Start the engine and let it idle.
7. Use the screwdriver 531 00 48-63 to adjust the L needle.
502 71 14-01
mixture).
needle.
loosen it 1 turn.
stop. The sleeve can now be turned without turning the
needle.
fuel mixture).
The blade is 2 mm wide and goes through the plastic
sleeve and only adjusts the needle.
531 00 48-63
Adjust the L needle so that the highest idling speed is
obtained.
Use the tachometer 502 71 14-01 to check the speed.
8. Check that the plastic sleeve on the L needle is still turned
as far as possible clockwise (leanest fuel mixture).
9. Press the plastic sleeve on the L needle using a punch
(Ø 5 mm).
The basic setting of the carburettor is now complete. Further
fine adjustment, within the limits that the plastic sleeves on the
needles permit, can be necessary.
502 71 14-01

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

322l325325l522l

Table of Contents