Advertisement
Quick Links
IMPORTANT:
Read Before Using
Operating/Safety Instructions
Consignes de fonctionnement/sécurité
Instrucciones de funcionamiento y seguridad
3100
Call Toll Free for
Consumer Information
& Service Locations
1-877-SKIL999 (1-877-754-5999) www.skil.com
For English Version
See page 2
IMPORTANT :
Lire avant usage
Pour obtenir des informations et
les adresses de nos centres de
service après-vente,
appelez ce numéro gratuit
Version française
Voir page 12
IMPORTANTE:
Leer antes de usar
Llame gratis para
obtener información
para el consumidor y
ubicaciones de servicio
Versión en español
Ver la página 12
Advertisement
Related Manuals for Skil 3100
Summary of Contents for Skil 3100
- Page 1 Consignes de fonctionnement/sécurité Instrucciones de funcionamiento y seguridad 3100 Call Toll Free for Consumer Information & Service Locations 1-877-SKIL999 (1-877-754-5999) www.skil.com For English Version See page 2 IMPORTANT : Lire avant usage Pour obtenir des informations et les adresses de nos centres de service après-vente,...
-
Page 2: General Safety Rules
Service Station or other competent repair service. USE ONLY SKIL REPLACEMENT PARTS; Any others may create a hazard. THE USE OF ANY OTHER ACCESSORIES NOT SPECI- FIED IN THE CURRENT SKIL CATALOG MAY CREATE A HAZARD. Tool Use DON’T FORCE TOOL It will do the job better and safer at the rate for which it was designed. - Page 3 Do not overload the working stand or use as ladder or scaffolding. Overloading or standing on the working stand cause the stand to be “top-heavy” and likely to tip over. Use only Skil replacement parts. Any others may create a hazard. cutting tool is accidentally contacted. Do not store materials on or near the table such that it is necessary to stand on the table to reach them.
-
Page 4: Double Insulated Tools
It is intended to be the mains switch for benchtop applications if your Skil power tool is used in the insert plate. It is also intended as a convenience outlet for use with your Skil Circular Saw and Miter Saw. - Page 5 Using Your X-Bench Work Station – No Assembly Required 1. Opening the X-Bench a. The X-Bench comes in the folded position and no assembly is required. In order to open the X-Bench, the user must pull and twist the main knob, located by the handle, to the open position (Fig. 1a). Fig.
- Page 6 7. Miter Saw Mounting a. There are three mounting holes that support most miter saw dimensions (Fig. 10). require you mount the miter saw to the X-Bench for safety. Note: close cut channel for miter saw use. Fig. 10 Latch is now in the open position.
- Page 7 Make sure X-Bench is not plugged in and WARNING main outlet is off. 8. Power Switch a. The female plug is located on the bottom of the switch and the male plug is located on the side of the switch box (Fig. 11). Connect the switch box to an electrical outlet by using an extension cord.
- Page 8 11. Tail Vise (Sold Separately) a. Locate the following parts: (1) Clamp block (MDF), (2) Guide rods, (1) Threaded rod, (6) Bolts and (6) Bolt covers. b. Position clamp block (MDF) over guide rods, and threaded rod as shown in figure 16 c.
- Page 9 Direction 15. Shelf and Tool Bag (Sold Separately) a. Shelf and tool bag come fully assembled. b. There are four hooks under the work bench (Fig. 23.) c. Attach the Velcro straps located on the shelf to the hooks under the table (Fig. 23). Note: Unit can fold up with shelf and bag attached.
- Page 10 15. Universal Insert Plate: a. A blank insert plate is provided with the X-Bench. This area is meant to be used only with the Skil insert plate technology which is sold separately. The insert plates which can be purchased separately are a jigsaw insert plate, sander insert plate, router insert plate and a drill press insert plate.
- Page 11 Direction of Cut Direction of Cut...