Casio XJ-UT312WN User Manual page 81

Command List
 While the projector is turned off, it can receive only following commands: check power on/off state
(PWR?), read light time (LMP?), and write power on (PWR1). Do not try to send any other
commands to the projector while it is turned off.
 Input of a valid signal must be in progress in order to use a command to turn on blank screen or
change the aspect ratio.
 You can use only the commands and settings that are equipped on your projector model.
 Entries in the "Function" column of the table below indicate that a command is read-only (
write only ( ).
Command
Name
PWR Power On/Off
SRC Selecting the Input
Source:
AIS Selecting the Audio Input 0: AUDIO IN, 1: AUDIO IN 1, 2: AUDIO IN 2, 3: AUDIO IN R L
BLK Blank Screen
VOL Volume*
VLP VLP specifies, as a numeric value, how much volume should be increased. VLM specifies
how much it should be decreased. For example, to change volume by a factor of 5, send "VLP5"
VLM
to increase it or "VLM5" to decrease it.
MUT Mute
PST Color Mode
ARZ Aspect Ratio
LMP Reads the cumulative light time (Returns the number of hours as an integer value.)
PMD Light Control
FRZ Freeze
KST Vertical Keystone
Correction
KSP KSP specifies, as a numeric value, how much vertical keystone correction should be
increased. KSM specifies how much it should be decreased. For example, to change vertical
KSM
keystone correction by a factor of 5, send "KSP5" to increase it or "KSM5" to decrease it.
5
HKS* Horizontal Keystone
Correction
HKP* 5 HKP specifies, as a numeric value, how much horizontal keystone correction should be
increased. HKM specifies how much it should be decreased. For example, to change horizontal
HKM* 5
keystone correction by a factor of 5, send "HKP5" to increase it or "HKM5" to decrease it.
KEY Executes key press
operation.*
Function
0: Off, 1: On
0: RGB1, 1: Component 1, 2: Video, 3: RGB2, 4: Component 2
6: Auto1 (RGB/Component), 7: HDMI1, 8: Network
10: Auto2 (RGB/Component), 13: CASIO USB Tool, 14: HDMI2
15: Templates
4: HDMI AUDIO IN, 5: HDMI1 AUDIO IN, 6: HDMI2 AUDIO IN
8: Network AUDIO
0: Off, 1: On
1
0 (mute) to 30 (maximum volume)
0: Off, 1: On
1: Graphics, 2: Theater, 3: Standard, 4: Blackboard, 5: Natural
0: Normal*
6: 4:3, 7: 16:10
0: Bright*
4: Light Output 6, 5: Light Output 5, 6: Light Output 4
7: Light Output 3, 8: Light Output 2, 9: Light Output 1
0: Off, 1: On
0 to 120*
0 to 120*
1: , 2: , 3: , 4: , 5: ENTER, 6: ESC, 10: FUNC, 11: MENU
6 12: POWER, 13: AUTO, 14: INPUT, 15: TIMER, 16: ASPECT
17: BLANK, 18: FREEZE, 19:
21: KEYSTONE –, 22: D-ZOOM +, 23: D-ZOOM –, 24: VOLUME +
25: VOLUME –, 31: ID2, 32: ID1, 33: ID4, 34: ID3
Settings
2 , 1: 16:9, 2: Normal* 2 , 3: Letter Box, 4: Full, 5: True
3 3
, 1: Normal* , 2: Light Sensor On, 3: Light Output 7
4
4
, 20: KEYSTONE +
81
) or