Specifications; Ec Declaration Of Conformity; General Power Tool Safety Warnings; Instruction Manual - Makita TM3010C Instruction Manual

ENGLISH (Original instructions)

SPECIFICATIONS

Oscillation per minute
Oscillation angle, left/right
Overall length
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s). The lightest and heaviest combination, according to
EPTA-Procedure 01/2014, are shown in the table.
Intended use
The tool is intended for sawing and cutting wood, plastic, gyp-
sum, non-ferrous metals, and fastening elements (e. g. unhard-
ened nails and staples). It is also intended for working soft wall
tiles, as well as dry sanding and scraping of small surfaces. It is
especially for working close to edge and flush cutting.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841:
Work mode: Sanding
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Work mode: Cutting with plunge cut saw blade
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Work mode: Cutting with segment saw blade
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Work mode: Scraping
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841:
Work mode : sanding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model
Net weight
Safety class
) : 80 dB (A)
pA
) : 80 dB (A)
pA
) : 79 dB (A)
pA
) : 82 dB (A)
pA
2
) : 2.5 m/s or less
h
2
6,000 - 20,000 (min
Work mode : cutting with plunge cut saw blade
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : cutting with segment saw blade
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : scraping
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE: The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.

General power tool safety warnings

WARNING:
Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
4 ENGLISH
TM3010C
-1
)
1.6° (3.2° total)
283 mm
1.6 - 1.7 kg
/II
2
) : 6.5 m/s
h
2
2
) : 2.5 m/s
h
2
2
) : 5.0 m/s
h
2