Table of Contents
Advertisement
Quick Links
CORDLESS SCREWDRIVER
ASSEMBLY AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SaVe THiS manual.
Copyright
2005 by Harbor Freight Tools
©
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
3.6 VOLT LITHIUM (LI)
Model 93432
3491 Mission Oaks Blvd., Camarillo, CA 93011
. All rights reserved. No portion of this
®
.
®
Advertisement
Table of Contents
Related Manuals for Harbor Freight Tools Chicago Electric 93432
Summary of Contents for Harbor Freight Tools Chicago Electric 93432
- Page 1 . All rights reserved. No portion of this © ® manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call 1-800-444-3353.
-
Page 2: Product Specifications
PRODUCT SPECIFICATIONS SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep this manual and invoice in a safe and dry place for future reference. -
Page 3: Electrical Safety
ELECTRICAL SAFETY Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. - Page 4 Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the power tool in unexpected situations. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
-
Page 5: Specific Safety Rules
SPECIFIC SAFETY RULES Maintain labels and nameplates on the Screwdriver. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Always wear ANSI approved safety impact eye goggles when using the Screwdriver. - Page 6 Always recharge the Battery (31) when tool performance begins to diminish. Never over-discharge a Battery by using the tool even after tool performance is decreasing. Never attempt to discharge a tool’s Battery by continuing to pull the tool’s Forward/Reverse Switch (49). When tool performance begins to diminish, stop the tool, and recharge the Battery for optimal performance.
-
Page 7: Grounded Tools: Tools With Three Prong Plugs
GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS Tools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. -
Page 8: Extension Cords
EXTENSION CORDS Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. - Page 9 When unpacking, check to make sure all the parts shown on the Parts List on page 13 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
- Page 10 To charge the Battery (31), insert the Charger’s (50) cable into the DC Plug (33) located at the top of the Screwdriver body. (See Figure E.) Plug the Charger (50) into a 120 volt, grounded, electrical outlet. (See Figure E.) Once the Battery is fully charged (within 3 to 5 hours) the Charger will automatically shut off.
- Page 11 To Install A Screwdriver Bit: The chuck of the Screwdriver is a self-locking type. When a screwdriver bit (not included) is inserted, the chuck will grip it automatically. If the bit is not long enough for the chuck to securely grip, connect a magnetic extension rod (not included) to the bit.
- Page 12 To Adjust The Torque: The Screwdriver is designed with 22 adjustable torque positions. To adjust the torque, turn off the Screwdriver and wait until the screwdriver bit stops rotating. Then, turn the Clutch Cap (7) to the desired setting. (See Figure G.) Operating Tips: When driving screws into wood or plastics, drill a pilot hole first in the workpiece.
-
Page 13: Inspection, Maintenance, And Cleaning
INSPECTION, MAINTENANCE, AND CLEANING WARNING! Make sure the Forward/Reverse Switch (49) of the Screwdriver is in its “PAUSE” (middle) position and the tool is disconnected from its Charger (50) prior to performing any inspection, maintenance, or cleaning procedures. Before each use, inspect the general condition of the Screwdriver and its Charger (50). -
Page 14: Parts List And Assembly Diagram
PARTS LIST AND ASSEMBLY DIAGRAM 1011 12 13 1819 20 21 22 23 24 25 26 45, 46 41, 42 43, 44 47, 48 50: CHARGER NOT SHOWN. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. For technical questions, please call 1-800-444-3353. -
Page 15: Limited 90-Day Warranty
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this prod- uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase.