Download  Print this page

Sinclair Surface Prep Machine 390 Operating Manual

Surface prep machine
Hide thumbs

Advertisement

1.0
2.0
3.0
4.0
5.0
6.0
7.0
390 Surface Prep Machine
Operating Manual
October 31, 2005
Read before use and keep safe

Table of Contents

(800) 624-2408 (530) 626-9386 Fax (530) 626-5144
6686 Merchandise Way Diamond Springs, Ca 95619
www.sineqco.com
Page 2
Page 2
Page 2
Page 4
Page 4
Page 6
Page 7

Advertisement

Table of Contents
loading

  Related Manuals for Sinclair Surface Prep Machine 390

  Summary of Contents for Sinclair Surface Prep Machine 390

  • Page 1: Table Of Contents

    390 Surface Prep Machine Read before use and keep safe Technical Data Safety Safety Instructions Maintenance Trouble Shooting Schematics (800) 624-2408 (530) 626-9386 Fax (530) 626-5144 6686 Merchandise Way Diamond Springs, Ca 95619 Operating Manual October 31, 2005 Table of Contents www.sineqco.com Page 2 Page 2...
  • Page 2: Technical Data

    Hand/Arm-Vibration Weight Includes: 2.0 Safety The Sinclair 390 Surface Prep is state of the art designed and meets all standard safety requirements. 3.0 Safety Instructions Disconnect the power supply before any maintenance is carried out. Use only recommended mounting discs and brushes. The mounting discs must have a plain surface.
  • Page 3 The 390 Surface Prep Machine is exclusively for wet cleaning and polishing of resilient and textile floor coverings and for grinding pavement and leveling compounds in dry environments. It should not be used for any other purpose. Sinclair is not responsible for any damage or loss caused by incorrect use.
  • Page 4: Maintenance

    4.0 Maintenance The 390 Surface Prep machine is virtually maintenance free. The roller bearing and gearbox need not to be lubricated. Mounting and changing the paper bags of the vacuum unit The vacuum unit can be used with paper bags or with the enclosed textile bag. release and pull the cover of the vacuum unit upwards insert paper bag remount the cover...
  • Page 5 Assembly of mounting discs, pads and brushes Lay the machine down on the handle. Thus the support of the discs is accessible. Put the mounting disc on the actuation and lock it by turning counter-clockwise. Assembly of the vacuum unit Assemble the vacuum unit with two supports to the handle.
  • Page 6 Operation with vacuum cleaner Note: the vacuum cleaner cannot – on technical grounds – remove the grinding dust from under the discs. It will always remove the fine dust. To clean the floor, use an industrial cylinder vacuum cleaner.
  • Page 7: Trouble Shooting

    6.0 Trouble shooting Trouble Machine does not start Switch-on lever cannot be actuated Eventual Power supply disconnected Blown Fuse Defective cable or plug Assembly of handle wrong, described in section 5.0 Safety lever can only be actuated, if handle not vertical Elimination Have machine repaired by a...
  • Page 8: Schematics

    7.0 Schematics Schematic # MACHINE Part # 021625 Top Cover + Motor Housing 021626 Base Link 021627 Rubber Washer 021629 Fastening Screw for Gear 021628 Balancing Weight 021629 Fastening Screw for Weight 021630 Fastening Screw for Housing 017284 Screw 4.8 x 13 017283 Axle Retainer 021631...
  • Page 9 Schematic # Part # 015439 2 & 11 014193 015440 015441 014814 015442 015443 015444 015445 015446 10.1 018611 015447 015448 015449 015450 015451 014194 015452 015453 021641 015455 014731 015457 021639 021638 014831 015461 015462 016922 021642 015467 015468 032678 032680 032681...
  • Page 10 ELECTRICAL INSTALLATION Schematic # Part # 021637 015493 015514 018014 018027 015496 015497 015498 014195 015500 015499 018419 033965 015502 018332 021662 015503 015504 015505 033962 Description Switch Holder Fastening Screw Switch Screw for Fixed Link Screw for Cover Cable Clip Holding Device Protective Rubber Sleeve Cable + Connector Plug...
  • Page 11 Schematic # Part # 015507 033963 018422 018237 015489 018424 018425 018426 015508 015509 018427 018428 018429 015510 015511 018219 GEAR Description Oil Seal Washer Top Cover O-Ring Washer Bearing E20 Lay Shaft Bearing 16-004 Bearing E15 Gear Shaft Gear Gear Holder Bearing 16.001 Planetary Box...
  • Page 14 “New Style,” Green 390 Surface Prep Schematic Schematic# Part# SP014038 SP014039 SP015352 SP015353 SP015354 SP015355 SP015356 106055 Vacuum Description Tube with branch connection Extraction ring with brushes Branch connection Brushes Adapter Supporting cage Suction Case Paper Bags 10/pk...
  • Page 15 Not responsible for lost job or down time. In no event shall SINCLAIR be liable for any indirect, incidental, or consequential damages from the sale or use of the product. This disclaimer applies both during and after the term of this warranty.
  • Page 16 Notes...