Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Simpson Electric Hawk H340
- Page 1 H340 4 Digit Advanced Digital Controller OPERATORS MANUAL SIMPSON ELECTRIC COMPANY 520 Simpson Avenue Lac du Flambeau, WI 54538-0099 (715) 588-3311 FAX (715) 588-3326 Printed in U.S.A. Part No. 06-117489 Edition 5, 06/07 Visit us on the web at: www.simpsonelectric.com...
- Page 2 This warranty shall not apply to any instrument or other article of equipment which shall have been repaired or altered outside the SIMPSON ELECTRIC COMPANY factory or authorized service centers, nor which has been subject to misuse, negligence or accident, incorrect wiring by others, or installation or use not in accord with instructions furnished by the manufacturer.
- Page 3 NOTES: NOTES...
-
Page 4: Table Of Contents
Contents 1. INTRODUCTION ... 5 General Description ... 5 1.2. Specifications ... 5 2. DISPLAY AND KEYPAD CONTROLS ... 6 3. INSTALLATION AND PANEL CUTOUT ... 6 Mounting Requirements ... 6 Engineering Label Placement ... 7 4. REMOVING / INSTALLING OPTION MODULES ... 7 5. -
Page 5: Introduction
INTRODUCTION General Description The Simpson Electric Hawk 3 Advanced Digital Panel Meter/Controller has 4- digit display. All LEDs are 7 segment and offer 5 brightness levels. The high quality instrument has user programmable parameters that are all set from the front panel in easy to understand terminology. -
Page 6: Display And Keypad Controls
DISPLAY AND KEYPAD CONTROLS Figure 2-1 INSTALLATION AND PANEL CUTOUT 1.77" 3.56 45mm 90.7mm 3.62" 92mm 0.52" 13.2mm 3.93" 3.24" 99.8mm 82.3mm 1.76" 2.04" 51.8mm 44.7mm Figure 4-1. Installation and Panel Cutout Mounting Requirements The Hawk 3 Advanced Digital Controller 1/8 DIN counters require a panel cutout of 1.77”... -
Page 7: Engineering Label Placement
Relay Control (Sp1-Sp4) While in menu, all other operations are suspended. The H340 has four setpoint parameters and up to four relays associated with those four setpoints. The setpoint LEDs on the display will light even if no relay is present for that setpoint. -
Page 8: Operating The Keys
OPERATING THE KEYS In Run Mode = Enters the Program Menu = Displays the Maximum Value (if enabled). Press RESET to clear max. value. ENTER = Displays Minimum Value, if enabled. Press and hold while pressing to clear min. value RESET = Resets Latched Relays (If any) RESET/E... -
Page 9: Programming Menu
MENU FLOWCHART Menu Mode VAL1 RSP1 ALR1 VAL2 RSP2 ALR2 VAL3 RSP3 ALR3 VAL4 RSP4 ALR4 DCTL Frsh Band Brit Page Value HYST Value DLAY LTCH Value HYST Value DLAY LTCH Value HYST Value DLAY LTCH Value HYST Value DLAY LTCH Value Value... -
Page 10: Display Control
& f i ( *Factory Reset Default Values Display Control l l u *Factory Reset Default Values Measurement Control i t c ) t i * f f l i t * f f The hold feature is used to freeze the display. When the contacts are shorted, the display will “Hold”... -
Page 11: Output Control (If Present)
The relay cards are directly related to any alarms that occur on the Hawk 3. The single relay is a “Form C” relay that activates in relationship to “SP1”. The dual relay is a Form C” relay that activates in relationship to “SP1” & “SP2”. -
Page 12: Temperature Input Cards
Password l l u . t r F " . " l a l i NOTE: If you forget your password, turn power off in unit, press and hold the key and the RE key. Turn power on and wait until the display reads “noPas” RESET ENTER then press the re...
Need help?
Do you have a question about the Hawk H340 and is the answer not in the manual?
Questions and answers