Fault code No.
Item
2
"01" is indicated in diagnostic
mode (code No. 60). EEPROM
data error for adjustment of CO
concentration of cylinder #1.
3
"02" is indicated in diagnostic
mode (code No. 60). EEPROM
data error for adjustment of CO
concentration of cylinder #2.
4
"03" is indicated in diagnostic
mode (code No. 60). EEPROM
data error for adjustment of CO
concentration of cylinder #3.
5
"04" is indicated in diagnostic
mode (code No. 60). EEPROM
data error for adjustment of CO
concentration of cylinder #4.
6
"11" is indicated in diagnostic
mode (code No. 60). EEPROM
data error for ISC (idle speed
control) learning values.
"12" is indicated in the diagnos-
tic mode. (Code No. 60)
EEPROM data error for O
back learning values.
"13" is indicated in the diagnos-
tic mode. (Code No. 60)
EEPROM data error for OBD
memory values.
P062F
EEPROM fault code number: an error is detected while reading or
writing on EEPROM.
Change the CO concentration of
cylinder #1, and rewrite in
EEPROM.
Refer to "ADJUSTING THE
EXHAUST GAS VOLUME" on
page 3-12.
After this adjustment is made,
turn the main switch to "OFF".
Change the CO concentration of
cylinder #2, and rewrite in
EEPROM.
Refer to "ADJUSTING THE
EXHAUST GAS VOLUME" on
page 3-12.
After this adjustment is made,
turn the main switch to "OFF".
Change the CO concentration of
cylinder #3, and rewrite in
EEPROM.
Refer to "ADJUSTING THE
EXHAUST GAS VOLUME" on
page 3-12.
After this adjustment is made,
turn the main switch to "OFF".
Change the CO concentration of
cylinder #4, and rewrite in
EEPROM.
Refer to "ADJUSTING THE
EXHAUST GAS VOLUME" on
page 3-12.
After this adjustment is made,
turn the main switch to "OFF".
Turn the main switch to "OFF".
feed-
2
8-90
FUEL INJECTION SYSTEM
Set the main switch to "ON",
and then check the condition of
the fault code using the mal-
function mode of the Yamaha
diagnostic tool.
Condition is "Recovered" Go
to item 8 and finish the service.
Condition is "Detected"
Repeat item 1.
If the same number is indicated,
go to item 7.
Set the main switch to "ON",
and then check the condition of
the fault code using the mal-
function mode of the Yamaha
diagnostic tool.
Condition is "Recovered" Go
to item 8 and finish the service.
Condition is "Detected"
Repeat item 1.
If the same number is indicated,
go to item 7.
Set the main switch to "ON",
and then check the condition of
the fault code using the mal-
function mode of the Yamaha
diagnostic tool.
Condition is "Recovered" Go
to item 8 and finish the service.
Condition is "Detected"
Repeat item 1.
If the same number is indicated,
go to item 7.
Set the main switch to "ON",
and then check the condition of
the fault code using the mal-
function mode of the Yamaha
diagnostic tool.
Condition is "Recovered" Go
to item 8 and finish the service.
Condition is "Detected"
Repeat item 1.
If the same number is indicated,
go to item 7.
Set the main switch to "ON",
and then check the condition of
the fault code using the mal-
function mode of the Yamaha
diagnostic tool.
Condition is "Recovered" Go
to item 8 and finish the service.
Condition is "Detected"
Repeat item 1.
If the same number is indicated,
go to item 7.