Simplicity 105308E Operator's Manual
  1. Manuals
  2. Brands
  3. Simplicity Manuals
  4. Snow Blower
  5. 105308E
  6. Operator's manual

Simplicity 105308E Operator's Manual

Large frame snowthrowers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Print Vendor
Instructions
Paper Size:
Press:
Bindery:
Covers:
Body:
General:
• 11x17
• Body - 50 lbs brilliant white offset or equivalent
• Cover - on pre-printed two tone "Swash" stock.
• Body - 1 color, 2-sided
• Cover - 1 color, 1 sided
• Saddle stitch, face trim
• FRONT COVER is present at the beginning of the file.
• BACK COVER is the page immediately after the front cover.
• The part number for this manual (typically a 172_____ number) is
located on the front cover.
• This file may contain several manual which differ only by their covers.
See the part number at the bottom of the cover page. .
• The body for all manuals is identical regardless of the cover.
• Odd number pages are always right hand pages, even number pages
are always left hand pages.
• This instruction sheet is NOT part of the manual and must not be
printed.
• Pages labeled "THIS PAGE INTENSIONALLY BLANK" are placement
pages and should NOT be printed.
How to use this file
Operator's Manuals
*if too thick for saddle stitch, tape bind

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 105308E and is the answer not in the manual?

Questions and answers

Related Manuals for Simplicity 105308E

Summary of Contents for Simplicity 105308E

  • Page 1 Print Vendor Instructions Paper Size: • 11x17 • Body - 50 lbs brilliant white offset or equivalent • Cover - on pre-printed two tone “Swash” stock. Press: • Body - 1 color, 2-sided • Cover - 1 color, 1 sided Bindery: •...
  • Page 2 THIS PAGE INTENTIONALLY BLANK (FOR PLACEMENT ONLY - DO NOT PRINT)
  • Page 3 E95288E, 9.5HP Snowthrower (CE) 10530 Models Mfg. No. Description 1694986 L10530E, 10.5HP Snowthrower 1695084 L10530EX, 10.5HP Snowthrower (CE) 1694995 105308E, 10.5HP Snowthrower 1695095 E105308E, 10.5HP Snowthrower (CE) 11532 Models Mfg. No. Description 1694987 L11532E, 11.5HP Snowthrower 1694996 115328E, 11.5HP Snowthrower 1695096 E115328E, 11.5HP Snowthrower (CE)

  • Page 4: Table Of Contents

    CONTENTS: Safety Rules & Information General...2 Training ...4 Preparation ...4 Operation...4 Children ...5 Clearing a Clogged Discharge Chute ...5 Service, Maintenance and Storage ...5 Emissions ...3 Decals...6 Safety Icons ...8 Identification Numbers...9 Features, Controls, & Operation Control Locations...10 General Operation Checks Before Each Start-Up ...12 Starting Controls...13 Starting the Engine...14...

  • Page 5: Operating Safety

    Safety Rules & Information Read the Manual The operator’s manual contains important safety information you need to be aware of BEFORE you operate your unit as well as DURING operation. Safe operating techniques, an explanation of the product’s features and controls, and maintenance information is included to help you get the most out of your equipment investment.

  • Page 6: Safety Rules And Information

    Moving Parts This equipment has many moving parts that can injure you or someone else. However, if you are standing in the operator’s position, and follow all the rules in this book, the unit is safe to operate. The auger and impeller have spinning parts that can amputate hands and feet. Do not allow anyone near the equipment while it is running! DO NOT clear the discharge chute by hand.

  • Page 7: Training

    Safety Rules & Information This machine is capable to amputating hands and feet and throwing objects. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.

  • Page 8: Children

    21. Keep in mind the operator is responsible for acci- dents occurring to other people or property. 22. Data indicates that operators, age 60 years and above, are involved in a large percentage of power equipment-related injuries. These operators should evaluate their ability to operate the unit safely enough to protect themselves and others from injury.

  • Page 9: Decals

    Decals DECALS This unit has been designed and manufactured to pro- vide you with the safety and reliability you would expect from an industry leader in outdoor power equipment. Although reading this manual and safety instructions it contains will provide you with the necessary basic knowl- edge to operate this equipment safely and effectively, we have placed several safety labels on the unit to remind you of this important information while you are operating...
  • Page 10 Part No. 1732618 Shift Decal Part No. 1733059 - DANGER / WARNING Main Dash Decal, CE, w/o Easy Turn Part No. 1727207 Discharge Chute Danger Decal ALL MODEL DECALS Part No. 1733443 Chute Release CE MODEL DECALS Part No. 1733060 - DANGER / WARNING Main Dash Decal, CE, w/ Easy Turn Part No.

  • Page 11: Safety Icons

    Safety Icons SAFETY ICONS WARNING: READ OPERATOR’S MANUAL. Read and understand the Operator’s Manual before using this machine. DANGER: THROWN OBJECTS. This machine is capable of throwing objects and debris. Keep bystanders away. WARNING: REMOVE KEY BEFORE SERVICING. Remove the key, disconnect spark plug wire, and consult technical litera- ture before performing repairs or maintenance.

  • Page 12: Identification Numbers

    Identification Numbers When contacting your authorized dealer for replace- ment parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer’s identi- fication numbers, and engine serial numbers in the space provided for easy access. These numbers can be found in the locations shown.

  • Page 13: Features, Controls, & Operation

    Please take a moment and familiarize yourself with the name, location, and function of these controls so that you will better understand the safety and operating instructions provided in this manual. CONTROL LOCATIONS The information below briefly describes the function of individual controls. Starting, stopping, and driving require the combined use of several controls applied in specific sequences.

  • Page 14: Auger Control

    Auger Control Engages the auger/impeller when depressed. Releasing the control stops the auger/impeller. Chute Direction Control Push the lever forward to unlock the rotator control. Moving the lever to the left will turn the spout to the left side and moving the lever to the right will rotate the spout to the right side.

  • Page 15: General Operation

    Operation GENERAL OPERATION CHECKS BEFORE EACH START-UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check to make sure that the clean-out is attached to the auger housing. Do not operate the machine with- out the clean-out tool properly stored on the auger housing.

  • Page 16: Starting Controls

    STARTING CONTROLS See Figure 1 for the following instructions. Electric Start A. Electric Start Button - The Electric Start Button (A) activates an electric starter mounted to the engine, eliminating the need to pull the starter han- dle. The Electric Start Button operates on 120 Volts AC, which is provided by connection to the extension cord provided with units equipped with this feature.

  • Page 17: Starting The Engine

    Operation STARTING THE ENGINE 1. Turn the fuel valve (B, Figure 1, Intek Models) to the ON position. 2. Switch the stop switch (H, Power Built models) to the on position. 3. Insert the engine key (F) into the engine key slot and push fully in to the RUN position.

  • Page 18: Ground Speed Selector

    GROUND SPEED SELECTOR Use the speed selector (A, Figure 2) to control the drive speed of the snowthrower. There are five forward speeds and two reverse speeds. Use the lower speeds to blow deep or wet snow. Use the higher speeds to blow light snow or to drive the snow- thrower without blowing snow.

  • Page 19: Easy-Turn And Traction Drive Lock

    Operation FULL TRACTION Both Wheels Drive Figure 5. Easy Turn Control EASY TURN™ FREEWHEELING AND TRACTION DRIVE LOCK While Clearing Snow: For easy turning when using the snowthrower, squeeze the Easy Turn™ lever (Figure 5). Engaging the Easy Turn™ lever releases the left traction wheel but allows the right wheel to continue driving (Figure 5).

  • Page 20: After Each Use

    AFTER EACH USE Normal use of the snowthrower may result in a build-up of packed snow in and around the starter cord housing and around engine controls. Heat from the engine will usually prevent the snow from freezing solid while the unit is running, but after the engine is shut down, some snow may continue melting from engine heat, and later freeze around some moving parts as the unit cools.

  • Page 21: Regular Maintenance

    MAINTENANCE SCHEDULE MAINTENANCE REQUIRED Check / Lubricate Free-Hand Linkage. Lubricate snowthrower. Check tire pressure. Change engine oil.* Clean or replace spark plug. Check drive linkage/belt tension. Lubricate Axle Shafts. Check auger gear case lubrication.** Lubricate Auger Shaft.*** * Change original oil after two hours of operation. ** Check oil level each fall and spring.

  • Page 22: Lubrication

    LUBRICATION IMPORTANT NOTE It is very important that grease fittings on the auger shaft are lubricated regularly. If auger rusts to shaft, damage to worm gear may occur if shear pins do not break. To prevent wheels rusting to axles, it is also necessary to remove the wheels and grease the axles regularly.

  • Page 23: Check / Lubricate Free-Hand Linkage

    Regular Maintenance CHECK / LUBRICATE FREE-HAND LINKAGE Check the function of the Free-Hand controls: the con- trols should function as described in the CONTROLS section. It is critical for the safe operation of the unit that the controls disengage when released. Lubricate as shown in figure 13.

  • Page 25: Troubleshooting, Adjustments, & Service Troubleshooting

    TROUBLESHOOTING This section provides troubleshooting and service instructions. Locate the problem and check the possible cause/remedy in the order listed. Also, refer to the engine manufacturer’s Owner’s Manual for additional information. For problems not covered here, contact your local deal- PROBLEM Engine fails to start.
  • Page 26 PROBLEM Auger rotates, but snow is not thrown far enough Poor traction Auger does not stop when auger lever is released Snowthrower does not stop when drive lever is released Snowthrower does not drive and auger does not rotate. Discharge control is difficult to operate.

  • Page 27: Traction Drive Cable Adjustment

    Adjustments AUGER DRIVE ADJUSTMENT WARNING Do not over-tighten, as this may lift the lever and cause auger drive to be engaged without depressing the Auger Control. 1. Check that the auger cable (A, Figure 15) is on top of cable button (B) as show in Figure 15. 2.

  • Page 28: Traction Drive Adjustment

    Figure 17. Traction Drive Cable Adjustment A. Cable Boot B. Traction Drive Cable C. “Z” Hook D. Cable Adjustment Bracket Note: If the cable is too slack the unit will not drive. If the cable is too tight the drive will be engaged without push- ing the handles down.

  • Page 29: Easy Turn Cable Adjustment

    Adjustments EASY TURN™ CABLE ADJUSTMENT If the Easy Turn™ cable has stretched, the gears will not disengage when the control lever is activated. Adjust the cable using the following procedure. 1. Turn the engine off and disconnect the spark plug wire.

  • Page 30: Shear Pin Replacement

    SHEAR PIN REPLACEMENT WARNING Do not go near the discharge chute or auger when the engine is running. Do not run the engine with any cover or guard removed. Under most circumstances, if the auger strikes an object which could cause damage to the unit, the shear pin will break.

  • Page 31: Belt Replacement

    Service BELT REPLACEMENT Auger Drive Belt The drive belts are of special construction and must be replaced with original factory replacement belts available from your nearest authorized service center. Some steps require the assistance of a second person. If the auger drive belt is damaged, the snow thrower will not discharge snow.
  • Page 32 Figure 27. Spout Rotator Rod A. Special Nut B. Cover C. Hair Pin D. Spout Rotator Rod 15. Index or point the spout rotator to the center of the machine so the rotator control is in the center of the dash panel.

  • Page 33: Traction Drive Belt

    Service Traction Drive Belt If the snow thrower will not move forward, check the trac- tion drive belt for wear or damage. If the traction drive belt is worn or damaged, replace the belt as follows. 1. Disconnect the spark plug wire. 2.

  • Page 34: Specifications

    NOTE: Specifications are correct at time of printing and are subject to change without notice. The power ratings for an individual engine model are initially developed by starting with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure) (Revision 2002–05). Given both the wide array of products on which our engines are placed, and the variety of environmental issues applicable to operating the equipment, it may be that the engine you have purchased will not develop the rated horsepower when used in a piece of power equipment (actual “on–site”...

  • Page 35: Technical Manuals

    REPLACEMENT PARTS Replacement parts are available from your authorized dealer. Always use genuine Simplicity / Snapper Service Parts. MAINTENANCE ITEMS Many convenient and helpful service and maintenance items are available from you authorized dealer. Some of these items include: Engine Oil...
  • Page 36 M A N U F A C T U R I N G , I N C . 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.SimplicityMfg.com P R O D U C T S 535 Macon Street McDonough, GA 30253 www.Snapper.com ©...

This manual is also suitable for:

115328e85268e95288eE105308eE115328eE85268e ... Show all

Table of Contents