Table of Contents
Advertisement
Quick Links
Introducing the CyberPro PCI 2S
The CyberPro PCI 2S high-speed serial I/O card provides
two additional 9-pin serial ports. Depending on the
model purchased, this board will fit into either a Full or
Low Profile chassis.
Features and Benefits
•
Conforms to PCI v2.2 Plug and Play
•
Full support for Windows-based software
•
Reduces CPU load and improves system
performance dramatically
•
IRQ sharing feature reduces IRQ conflicts
•
High-speed serial port (9-pin) works with 56K V.90
external modems, ISDN terminal adapters, PDAs,
digital cameras, label printers and other serial port
devices
•
Built-in FIFO buffers dramatically increase data
transmit/receive speed, especially under Windows'
multitasking environment
•
Each serial port can be configured for either 5V or
12V output, for serial devices that require power
System Requirements
•
Pentium or equivalent computer with an available
PCI slot
•
Windows
/64-bit)/Server 2003 (32-/64-bit)/Vista (32-/64-bit)
04-0342C
CyberPro PCI 2S
Quick Installation Guide
95/98/98SE/ME/NT 4.0/2000/XP (32-
®
1
Advertisement
Table of Contents
Related Manuals for SIIG I/O Expander 2S
Summary of Contents for SIIG I/O Expander 2S
-
Page 1: Quick Installation Guide
CyberPro PCI 2S Quick Installation Guide Introducing the CyberPro PCI 2S The CyberPro PCI 2S high-speed serial I/O card provides two additional 9-pin serial ports. Depending on the model purchased, this board will fit into either a Full or Low Profile chassis. Features and Benefits •... -
Page 2: Package Contents
Package Contents • CyberPro PCI 2S board • 2-port fan-out cable • Low profile bracket (Dual Profile board only) • Driver CD • Quick installation guide Layout Full profile bracket* JP2 (Serial port 2) Fan-out cable connector (25-pin) JP1 (Serial port 1) * Note: Depending on the model purchased, the bracket size will be either Full or Low profile. -
Page 3: Hardware Installation
Fan-out Cable 25-pin connector Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. -
Page 4: Driver Installation
Set JP1 and JP2 jumper settings to the desired voltage only if your serial device needs additional power from the serial port. However, most serial devices do not require additional power. information see Figure 1 on page 2. The jumpers can be removed if power is not required. - Page 5 Windows 98/98SE At the Add New Hardware Wizard, click Next. Select Search for the best driver for your device (Recommend), then click Next. Insert the driver CD, check Specify a location, uncheck the other boxes, type in D:\9x, then click Next.
- Page 6 Double click Multi-function adapters, SIIG CyberPro 2S PCI board and PCI Function should be displayed. Windows NT 4.0 From the desktop click Start, then Run. Insert the driver CD, type in D:\NT4\Install_serial.exe, then click OK. (Change D: to match your CD-ROM drive letter) Click Next when the Welcome window appears.
- Page 7 32-bit Windows XP/Server 2003 At the Found New Hardware Wizard, insert the driver CD. For XP w/SP1 or earlier/ Server 2003: go to step #2. For XP w/SP2 or later/Server 2003 wSP1 or later: select No, not this time, click Next. Select Install the software automatically (Recommended, then click Next.
- Page 8 Device Manager. Click on the + (plus sign) in front of Ports (COM & LPT), CyberSerial PCI 16Cxxx... should be displayed two times. Double click Multifunction adapters, SIIG CyberPro 2S PCI board should be displayed. Windows Vista ™ At the Found New Hardware window, insert the driver CD, click Locate and install driver software (recommended), then click Continue.
- Page 9 Changing COM Port Address Some serial devices need a specific COM port in order to work. If your serial device works properly, do not change this setting. Windows 95/98/98SE/ME From the Device Manager window double click Ports (COM & LPT), then double click the CyberSerial PCI serial port you want to change.
- Page 10 Blank Page...
-
Page 11: Technical Support And Warranty
Step 1: Submit your RMA request. Go to www.siig.com, click Support, then RMA to submit a request to SIIG RMA. If the product is determined to be defective, an RMA number will be issued. SIIG RMA department can also be reached at (510) 413-5333. - Page 12 6078 Stewart Avenue Fremont, CA 94538-3152, USA CyberPro PCI 2S is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Microsoft, Windows and Windows Vista are registered trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel Corporation. Other names used in this publication are for identification only and may be trademarks of their respective companies.