[Class 1 LED product (classification as per IEC 60825-1)]. Safety precautions Only use original Siemens bat- teries (100 % mercury-free) and charging devices. Otherwise you risk serious damage to health and property. The battery could explode, for instance.
The phone may cause interfer- ence in the vicinity of TV sets, radios and PCs. Use only Siemens original accessories. This will avoid potential risks to health or prop- erty and ensure compliance with all relevant regulations.
Telephone list (schematic) Call key Dial phone number/name displayed/ highlighted, take calls. Show last phone numbers dialled in standby mode. On/Off/End key • Switched off: Press and hold to switch on. • During a conversation or in an appli- cation: press briefly to finish. •...
Telephone list (schematic) Integrated antenna Do not obstruct the phone above the battery cover unnecessarily. This reduces the signal quality. LED for Dynamic Light (p. 79) Loudspeaker Display Infrared interface (IrDA) Input keys Ringtone • Press and hold in standby mode: Switch all audible signals on/off (except alarm).
Display symbols Display symbols (selection) Signal strength Charging Battery charge level, e.g. 50 % Phonebook Records Surf & fun Service supplier portal Organiser Messages Camera Extras File management Settings All calls are diverted Ç Ringing tone off ¿ Short ring (beep) only ¾...
Display symbols Message symbols (selection) Unread Read Draft Sent MMS not sent MMS received MMS read MMS with DRM contents (p. 13) E-mail forwarded E-mail with attachment Voice mail received À Camera symbols Switches between photo and video Ø Brightness Ù...
Getting started Inserting the SIM card/ battery The service provider supplies you with a SIM card on which all the important data for your line is stored. If the SIM card has been delivered in credit-card size, snap the smaller segment out and remove any rough edges.
Getting started Additional information Please switch off your phone before removing the battery! Only 3 V SIM cards are supported. Please contact your service provider if you have an older card. Charging the battery Charging the battery The battery is not fully charged when delivered.
Additional information The power supply unit heats up when used for long periods. This is normal and not dangerous. If the battery is removed for longer than 30 seconds, the clock must be reset. Changing CLIPIt™ covers You can use CLIPIt™ covers (accesso- ries) to adjust the appearance of your phone according to your per- sonal taste.
Switching phone on and off/entering PIN Switching phone on and off/entering PIN Switching phone on and Hold down the On/Off/End key. Enter PIN The SIM card can be protected with a 4 to 8-digit PIN. Enter the PIN using the number keys.
General instructions Standby mode The phone is in standby mode and is ready for use when the name of the service provider appears on the dis- play. Hold down the On/Off/End key to return to standby mode from any situation. Signal strength Strong receive signal.
General instructions User guide Menu controls The steps needed to reach a function are shown in a condensed form in the user guide, e. g. to display call list for missed calls in condensed form: ¢ ¢ Calls missed This comprises the following steps: Open the main menu.
Standard functions Option menus Functions which appear repeatedly in the options menu are listed here. Open menu. §Options§ Edit Open the entry to edit. View Display entry. Delete/ Delete entry/delete all Delete all entries after confirmation. New entry Create new entry. Send...
Standard functions Highlighting mode With some applications (e.g. Phone- book/Addressbook) one or more entries in a list can be highlighted to carry out a function jointly. §Options§ Open menu. Activate highlighting Mark mode. If a non-highlighted entry is selected, this can be highlighted: The current entry is high- §Mark§...
Security The phone and SIM card are pro- tected against misuse by several security codes. Keep these confidential numbers in a safe place where you can access them again if required. Codes Protects your SIM card (per- sonal identification number). PIN2 This is needed to set the charge detail display and to access...
Following the third unsuccessful attempt, access to the phone code and the functions that use it is denied. Contact the Siemens Service (p. 118). Clearing SIM card barring If the PIN is entered incorrectly three times, the SIM card is barred. Enter...
Text entry Text entry without T9 Press number key repeatedly until the required letter appears. After a brief interval the cursor will advance. Example: Press once briefly to type the letter a, twice to type b etc. Hold down to write the number.
Text entry Input menu With text input: Press down: The input menu is displayed: Text format Input language Mark Copy/Insert Text entry with T9 "T9" deduces the correct word from the individual key entries by making comparisons with an extensive dic- tionary.
T9 word suggestions If several options are found in the dictionary for a key sequence (a word), the most probable is dis- played first. If the word you want has not been recognised, the next sug- gestion from T9 may be correct. The word must §highlighted§...
Text entry Text modules Text modules can be stored in the phone for adding to your messages (SMS, MMS, e-mail). Write text modules ¢M¢ Text modules Select §Options§ Write text module. Open menu and select §Options§ Save. Accept the specified name or allocate a new one.
Where do I get what? You can purchase additional ring- tones, logos, animations and Java applications from your service pro- vider or directly from Siemens. Service supplier portal Depending on your service provider, you will find direct access to his por- tal on your telephone via menu items or bookmarks.
Calling Calling Dialling with number keys The phone must be switched on (standby mode). Enter the number (always with prefix/international dialling code). A short press clears the last digit, a long press clears the entire phone number. Press the Call key. The dis- played phone number is dialled.
If the number is busy If the called number is busy or can- not be reached because of network problems several options are availa- ble (depending on the service pro- vider). An incoming call or any other use of the phone interrupts these functions.
Calling Accept call The phone must be switched on. An incoming call will interrupt any other use of the phone. Press. Press. A phone number and the name of the caller transmitted by the net- work will be displayed if the number is saved in the Phonebook/Address- book.
Incoming calls during a call You may need to register for this serv- ice with your service provider and set your phone accordingly (p. 82). Dur- ing a call, you may be advised that there is another call waiting. You will hear a special tone during the call.
Calling Call options The following functions are only available during a call: Open menu. §Options§ Hold Maintain current call. Microphone If switched off, the person on the other end of the line cannot hear you (muting). Also: Handsfree Call via the loudspeaker. Volume Adjust handset volume.
Tone sequences (DTMF) You can, for example, enter control codes (numbers) for remote access to an automatic answering machine while another connection exists. These entries are transmitted directly as DTMFcodes (control codes). Open menu. §Options§ Send DTMF Select. Using the Phonebook/ Addressbook Store phone numbers and control codes (DTMF codes) in the Phone-...
Default book Default book ¢ ¢ Select function. Show entries The entries in the standard directory (Addressbook or Phonebook) are shown. Select a name with the first letter and/or scroll. New entry Create new entry. (see also p. 35) Phonebook Addressbook (see also p.
Addressbook The Addressbook can store up to 1000 entries, each with a variety of telephone and fax numbers as well as additional address details. These entries are managed separately from those in the Phonebook in the phone memory. However, you can exchange data between the Addressbook and the Phonebook on the SIM card.
Temporary switch to Phone- Î book. Synchronisation With the mobile phone manager, (p. 113) you can synchronise your Addressbook with Outlook® and other Siemens tele- phones. Using Remote sync. you can synchronise your mobile with an organiser stored on the Internet (see also p.
Change entry Open Addressbook (in standby mode). Select required entry. Press. §Edit§ Select input field. Open entry. §Edit§ Make changes. Save. §Save§ Dialling an entry Open Addressbook (in standby mode). Select a name with the first letter and/or scroll. The number is dialled. If there are several numbers in the address book entry, these are offered for selection.
Addressbook Groups Nine groups are specified in your phone to enable you to arrange your Addressbook entries clearly. You can rename seven groups. Open Addressbook (in standby mode). <Groups> Select (the number of entries is listed behind the group name). Select group.
Phonebook Entries in the Phonebook (on the SIM card) are managed separately from those in the Addressbook. You can, however, exchange data between the Phonebook and the Address- book. New entry If the Phonebook has been selected as standard: Open Addressbook (in standby mode).
Phonebook Call (search for an entry) Open Phonebook. Select a name with the first letter and/or scroll. Number is dialled. Call using record no. A record number is automatically assigned to every new entry in Phonebook. Enter record number. Press. Press.
<Special books> Open Addressbook (in standby mode). <Special books> Select. <Own numbers> Enter "own" phone numbers in Phone- book (e.g., fax) for information. These numbers can be changed, deleted and also sent as an SMS message. <VIP numbers> Display the phone numbers saved in group.
Call records Call records The phone number of a caller is dis- played if • the caller has switched off the Incognito function and • the network supports the "Caller Identity" function. Alternatively, a caller’s name is dis- played if it is stored in the Phone- book / Addressbook.
Durat/charges You can display the charges and duration during a call. You can set a unit limitation for outgoing calls. ¢ ¢ Durat/charges Select Last call All outg. calls All incoming Remain. units Charge sett. Select. Open report or settings. Reset the selected report.
Camera Camera You can view photos/videos recorded on the integrated camera immediately, • use the photo as a background image, logo, a switch on/off animation or a screensaver. • send the photo/video via MMS or e-mail. Switch on ¢ Starts camere in standby mode.
Premium: 640 × 480 (VGA) High: 320 × 240 (QVGA) Medium: 160 × 120 (QQVGA) Wallpaper: 132 × 176 The resolution may decrease depending on the selected digital zoom. Video mode The video mode resolution is the same as the preview image resolu- tion.
Inbox Inbox The central input folder offers imme- diate access to the messages cur- rently received. This means that you no longer have to look through all input folders for the various mes- sage types. The entries are marked with a symbol to indicate their type and status.
You can transmit and receive very long messages (up to 760 charac- ters) on your phone. They are auto- matically composed of several "nor- mal" SMS messages (note higher charges). Additionally you can insert pictures and sounds in an SMS. Write/send ¢...
Picture&sound Send the pictures and tones with or without accompanying text. Remember that these may be pro- tected (DRM, p. 13). The text input field is open: Open menu. §Options§ Select Picture&sound. The menu contains: Fix animations Fix sounds Own animat. Own pictures Own sounds Select area.
Read Arrival of a new SMS announced in the display. Open it with the display key beneath it (p. 42). Reading the SMS. Scroll through message line by line. ç SMS 10.05.2004 + 12398765431 SMS text. . . Delete Reply You can answer the SMS now open immediately.
Lists All SMS messages are archived in dif- ferent lists, according to their status. (List of message symbols, see p. 7): Inbox ¢ ¢ ¢ Inbox The list of received SMS messages is displayed. Draft ¢ ¢ ¢ Draft The list of not yet transmitted SMS messages is displayed.
Setting SMS signature ¢ ¢ Msg settings ¢ ¢ SMS signature You can enter a “signature” with a maximum of 16 characters. This sig- nature will then be attached to each SMS except and when changes §Reply§ are made to an existing SMS. SMS profiles ¢...
More information on SMS SMS status report If the message cannot be transmit- ted to the service centre you are offered the chance to repeat the transmission. If this also fails, con- tact your service provider. The message only indicates sage sent! transmission to the service centre.
The Multimedia Messaging Service enables you to send texts, pictures/ videos and sounds in a combined message to another mobile phone or to an e-mail address. All elements of an MMS message are merged to form a "slide show". Depending on your phone's settings, you will receive either the complete message automatically or notifica- tion that an MMS has been saved in...
Open Display picture. Delete Delete inserted picture/video. Save Save picture/video for use later on. Msg. details Display properties, incl. any user right restrictions (p. 13). Sounds <Sound> Select. Display sound functions: Insert sound Open list to select a tone. Record Activate tone recording in order to record tones (p.
Generation options §Options§ Open menu. Send MMS Send MMS. Play Play entire MMS on the display. Picture... See above. Sound... See above. Text... See above. Page page: Insert new page behind current one. Delete page: Delete cur- rent page. Page list: Display available pages.
Sending an MMS The page(s) of the new MMS is (are) already created and the MMS is dis- played. Open address entry. ç MMS Subject: Greetings from Munich Send to: +1234567654321 | Size: 85 KB ß á Þ Enter a brief description. Subject: Send to: Enter one or more phone...
Sending options §Options§ Open menu. Send MMS Send MMS. Play Play entire MMS on the display. Edit Object selection to change an object. Add recipient from the cur- recipient rent address directory. Delete Delete individual recipient. recip. Add attachment: attachm. •...
Reading an MMS An MMS has been fully received. Select the MMS. Start automatic playing of the MMS. Key functions for playback: To the next page. Press briefly once to return to the start of the current page; press briefly twice to return to the start of the previous page.
List options Different functions are offered depending on the list/situation. Open menu. §Options§ Play Play MMS on the dis- play. Edit Display MMS for processing. View Display MMS for view- ing only (write-pro- tected). Send MMS Send MMS. Reply MMS Reply to MMS immediately.
User settings Set the MMS dispatch to suit your requirements: Delivery Request delivery confirma- report: tion for sent messages. Read reply: Request confirmation that the MMS has been read. Default Send priority: priority: Normal, High, Validity: Select the period in which the service centre is to try to deliver the message: Manual,...
E-mail Your phone has an e-mail program (client). You can use it to create and receive e-mails. Write ¢ ¢ Write message Enter the address data for the e-mail: Enter one or more Send to: E-mail address(es). Insert them from the Ï...
E-mail Receive/read ¢ ¢ Inbox ¢ Select function. Before an e-mail can be read, it must be retrieved from the server. You have two options: Retr. e-mail Only the message header in (p. 42) is sent. You can then decide if you also want to receive the con- tents: Open menu and select...
Most of this data has already been entered. If not, you can obtain this from your service pro- E-mail vider. See also on the Internet at: www.siemens-mobile.com/screensaver Accounts Activating access Inbox (p. 42). Set access §Edit§...
Voice message/mailbox Voice message/mailbox ¢ ¢ ¢ Setup Most service providers provide a mailbox in which a caller can leave a voice mail for you if • if your phone is switched off or not ready to receive, • if you do not want to answer, •...
Inst. message With this function you can transfer text, audio clips, pictures and files straight to and from one or more ter- minals (mobile phone, PC). This function is not offered by all service providers. Please ask your service provider about this. Your dialogue partners are entered in contact lists.
Inst. message Login ¢ ¢ Inst. message Select the last access to be used (see also Automatic login: Contact lists When the connection has been established, the contact list or the list of the contact lists is shown for selection. In the contact list, you will find a list of the most recently used contacts.
Managing the groups Select one of the groups you set up yourself. Open menu. §Options§ Select. Manage Manage group Different functions are offered depending on the selection: Add member Add a new group member, see also Search Search for group member. memb.
Inst. message Creating a new contact list The current contact list is displayed. Open menu. §Options§ Contact list Available contact lists are displayed. Open menu. §Options§ Select. Create Contact list ID: Give the contact list its own, specific name. Allocate self-explanatory Name: names.
Start chat A contact list must be displayed. Select a contact or a group. Start communication with the contact. The page is displayed. During Inst. Message with a group, the name of the sender is placed in front of each contribution. Open editor.
Inst. message Options (group contact) §Options§ Open menu. Leave group Exit group. Details Information about the group: Group ID:, Name:, Topic:, Owner: Clear all Delete all texts in the cur- rent Inst. Message. Receiving objects You will be informed in the display if sounds or pictures are sent to you during a dialogue.
My settings Information on your current per- sonal status: Alias: Your own alias by which you can be found on the server. AIM screen Name to be displayed in name: the group. Mood: Information about your own mood, e.g. Happy, Sad, Sleepy, etc. Status text: Random text information, e.g.
CB services CB services ¢ ¢ ¢ Setup Some service providers offer infor- mation services (info channels, Cell Broadcast). If reception is activated, your Topic list will supply you with messages on the activated topics. CB messages are displayed in standby mode, longer messages are scrolled automatically.
• Bookmark site current page is saved as a bookmark. Enter URL for direct dial to an Internet address, e.g. wap.siemens- mobile.com Reload current page. Display the URL of the page currently loaded for sending via SMS/MME/ e-mail.
Surf & fun End connection Press and hold to clear down the connection and close the browser. Navigation in the browser • Select a link. • Settings, status on/off. • Press briefly: back a page. • One input field/link forward/back. •...
Profiles Preparation of the phone for Internet access depends on the service pro- vider concerned: Profile pre-set In most cases, access profiles have already been created for one or more service provider(s). Select profile. Activate profile. Set profile manually If necessary, contact your service provider.
Most applications include instructions. Some applications and games are already pre-installed on your telephone. You will find these listed here: www.siemens-mobile.com/t9 Requirements WAP profile (p. 71) and the access (p. 88) must be configured. Download Select the correct access depending...
Internet. Downloading or running applications will not affect or change the software already installed on your Java™-enabled mobile phone. Siemens excludes all warranty and liability claims in respect of or in connection with any applica- tions subsequently installed by the customer and any software not included in the original delivery package.
Setup Setup Profiles ¢ ¢ Profiles Several settings can be stored in a phone profile in order, for example, to adapt the phone to the surround- ing level of noise. • Five standard profiles are provided with default settings. They can be changed however: Normal environment Quiet environment...
Rename Change personal profile (except default profiles). Car Kit If an original Siemens Car Kit is used, the profile is switched on automati- cally as soon as the phone is inserted into the cradle (see accessories also). Headset...
Themes ¢ ¢ Themes Load a completely new user inter- face in your telephone. With the press of a key, various functions are re-organised on a topic basis, e.g. Switch on/off animation, back- ground image, screensaver, switch on/off melody, additional anima- tions.
Display ¢ ¢ Display ¢ Select function. Language Set the language of the display text. When "automatic" is set, the lan- guage of your home service provider is used. If a language that you do not under- stand happens to be set, the phone can be reset to the language of your home service provider with the fol- lowing input (in standby mode):...
Timeout Set period after which the screen- saver starts. Security To terminate the screensaver, the telephone code is requested. Auto key lock Automatic keypad locking if no key has been pressed for one minute in standby mode. Unlocking: Press down. Note Bitmap (animated) and...
Dynamic light ¢ ¢ Dynamic light ¢ Select function. The LEDs beneath the top of the phone are used to optically signal various functions. Show effects Switch on function. Select You can set the optical signals for the following functions: Standby Net search d Calls...
Ring tones ¢ ¢ Ring tones ¢ Select function. Set the tones on the telephone to suit your requirements. Ringer setting Activate/deactivate all On/off tones. Reduce ringtone to a Beep short signal (beep). Silent alert To avoid the disturbance caused by a ringing phone, you can activate the silent alert function as an alterna- tive.
Allocating a ringtone A ringtone which has already been selected will be played or the list of possible ringtones will be displayed for selection. d Calls Allocate a single ringtone to all phone numbers in the Addressbook. Group calls Allocate a different ringtone to each group.
Call setup ¢ ¢ Call setup ¢ Select function. Hide ID When you make a call, your phone number can be displayed on the recipient's display (depending on the service providers). To suppress this display, you can enable the "Hide ID" mode for all sub- sequent calls or just for the next call.
No reply A call is only diverted after a delay that is determined by the network. The period can be set to a maximum of 30 seconds in 5 second intervals. Busy Divert occurs if a call is in progress. Call waiting is activated (p.
Phone setup ¢ ¢ Phone setup ¢ Select function. Key tones Set the type of acoustic key acknowledgement. Info tones Set service and alarm tones: Activate/deactivate tones. On/off If switched on, a wider Extended range of service tones is available, e.g.: end of menu reached, network connection interrupted.
File system Format (Phone-code protected) The telephone memory is formatted and all saved data such as ringtones, pictures, games, etc. is deleted. Clean up Creating more memory by deleting temporary, non-requird files. Master reset Reset phone to default values (fac- tory setting).
Clock ¢ ¢ Clock ¢ Select function. Time/date The clock must be set correctly once at start-up. Press. §Change§ First enter the date (day/ month/year), then the time (hours/minutes/ seconds). Additional information If the battery is removed for longer than 30 seconds, the clock must be reset.
Connectivity ¢ ¢ Connectivity ¢ Select function. GPRS (General Packet Radio Service) Switch GPRS on/off GPRS is a new method for transmit- ting data faster in the mobile net- work. Use GPRS and if the network has sufficient capacity, you can be connected to the Internet perma- nently.
If necessary, check with your service provider for details. You will find the current settings for the service pro- vider in the Internat at this address: www.siemens-mobile.com/customercare in the FAQ section. Select profile Select the profile. Confirm selection.
Authentication Activate or deactivate encrypted WAP dial-up (CSD connections only). Fax/data Fax/data mode using a PC With the phone and a connected PC, you can transmit and receive faxes and data. Appropriate software for fax and data communication must be available on your PC and there must be a connection to the phone.
Security ¢ ¢ Security ¢ Select function. Auto key lock If activated, the keypad is locked automatically if no key has been pressed for one minute in standby mode. This prevents the phone from being used accidentally. However, you can still be called and you can still make an emergency call.
Barrings Barring restricts the use of your SIM card (not supported by all service providers). You need a 4-digit net- work password for network barring. Your service provider will give you this password. You may need to be registered separately for each barring.
Network ¢ ¢ Network ¢ Select function. Line This function is only displayed if it is supported by the service provider. Two separate phone numbers must be registered on the phone. Select line Select the currently used phone number. Display current phone number.
Your service provider is displayed: Display list of preferred §List§ networks. Create/change entry: or select an existing entry, <Empty> then select a new service provider in the list and confirm. Record new service provider (last entry in the list): Furth.network Select, enter the provider data and save it.
Headset Only in conjunction with an original Siemens headset (see accessories). If an original Siemens Headset is used the profile is automatically activated when the headset is plugged in. Auto answer (factory default: off)
My menu Press. Press. §My menu§ Create your own menu with fre- quently used functions, phone num- bers or WAP pages. The list of 10 entries is preset. You can, however, change it as you want. Select the required entry. Confirm.
Fast access key Fast access key You can assign one important phone number of a function to each one of the two soft keys and number keys 2 to 9 (speed-dial numbers). The phone number can then be dialled or the function can be started at the touch of a button.
Speed keys Number keys 2 to 9 can be used as speed dialling numbers for fast access. Number key 1 is reserved for the mailbox phone number (p. 60) and number key 0 is reserved for switching over two connections dur- ing use (p.
Organiser Organiser Calendar ¢ ¢ Calendar You can enter appointments in the calendar. Time and date must be set for the Calendar to work correctly. The calendar offers you three views: Monthly view Special colour coding: Day with entries for appointments, day-long appointments, weekend Navigation: One day forward/back.
Appointments ¢ ¢ Appointments Appointments are displayed in chronological order in a list. Enter new appointment <New entry> Select. Types: Memo Text input for description Voice memo Enter voice memo. Shown with alarm. Call Enter phone number to be displayed with the alarm.
Organiser Alarm time: On/off Silent alert. Enter the timespan before the appointment and select the time unit: Minutes, Hours, Days. Reoccurrence: Select a timeframe for repeating the appointment: No, Daily, Weekly, Monthly, Yearly. Enter a parameter for repeating: Forever, Until, Occurrences is selected, certain week- Weekly...
Status: Choose between: Done Priority: Selection in 5 levels of Highest. Use date If activated with Yes, the following time-input option is offered. Due date:/Expiry time: Enter the date and time by when the task is to be completed. Alarm: and Standard as for ments.
Organiser Dictating mac ¢ ¢ Dictating mac Use the dictating machine to record short voice memos. • Use your phone as a dictating machine when on the move. • Record a memo as a reminder or as a note for others. •...
Time zones ¢ ¢ Time zones The time zone can be selected in the world map or a city list: World map Select the desired record- ing. City list Select a city in the selected time zone. Time zone options §Options§...
Extras Extras SIM services (optional) ¢ ¢ SIM services Your service provider may offer spe- cial applications such as mobile banking, share prices, etc. via the SIM card. If you have such a SIM card, the SIM services will appear in the main menu under "Extras"...
Sound recorder Use the sound recorder to record noises and tones for use as ring tones. The tone recording is nor- mally started by other applications/ functions such as "assign ring tone". New recording Start from main menu ¢ ¢ Sound recorder <New entry>...
Extras Calculator ¢ ¢ Calculator The calculator can be used in a basic version and with an advanced range of functions. The input line and two calculation lines (including the matrice with the calculation func- tions) are located in the top display half.
Convert Select the source unit/ currency. Switch to the input field. Enter the quantity to be converted. Switch to the selection field. Select the target meas- urement unit / currency The result is displayed. You can use both input fields alter- nately.
(addresses, calendar, etc.) and syn- chronise these with the data on your phone. The data can, for example, be saved on a company computer or in the Internet. www.siemens-mobile.com/syncml Syncronise The computer is selected §Sync§ and synchronisation started. When completed,...
Server sett. Providers Display the current service provider. Homepage: e.g. www.siemens- mobile.com/ cx65syncml Port: Enter port number, e.g. 80. Login: Enter user name (Login name). Password: Enter password (shown as a series of asterisks). Calendar e.g., events path Contacts e.g., contacts path e.g., notes...
Media player Media player When you are viewing a picture/ video or listening to a melody, the application starts a media playback. Scroll to the next media file. Switch on display light- – ing. Pictures The following functions can be applied to a displayed picture: Zoom function if the dis- played picture has a...
My stuff To organise your files, you can use the file system like a PC file manager. There are some folders in the various data types for this pur- pose. ¢ The list of the folders and files is dis- played.
My stuff Index structure Some folders have already been cre- ated for different data types in stuff. These folders cannot be changed. Folder Description Pictures Pictures Videos Videos Anima- Switch on/off ani- tions mations Sounds Melodies Themes Loaded theme (zipped) Theme configura- tion (unzipped) Skins...
You can adjust and copy con- tacts between your telephone, Outlook® and other Siemens tele- phones (incl. Gigaset). Mobile Phone Manager SMS and MMS management Create MMS and SMS quickly and easily from your PC.
Mobile Phone Manager Bookmarks management (browser & bookmarks) Browse through the WAP with your PC and specify your preferred WAP- pages. Save the WAP-addresses as bookmarks on your telephone so that you can then call them up quickly later on. Phone explorer You can read your telephone’s file system with the phone explorer.
Questions & Answers If you have any questions on the use of your phone, you can contact us at www.siemens-mobile.com/customercare around the clock. As further help we have listed below some frequently asked questions and answers. Problem Possible causes Phone cannot be On/Off key not pressed long switched on.
Questions & Answers Problem Possible causes No network connec- Weak signal. tion. Outside GSM range. Invalid SIM card. New network not authorised. Network call barring is set. Network overloaded. Phone loses net- Signal too weak. work. Calls not possible. Second line set. New SIM card inserted.
Enter the PUK (MASTER PIN) supplied with the SIM card according to the instructions. If the PUK (MASTER PIN) has been lost, please contact your service provider. Contact Siemens Service (p. 118). Check with your service provider. Check settings (p. 89). # 9 9 9 9 #...
When calling customer service, please have ready your receipt and the phone identity number (IMEI, to display press software version (to display, press then info) and if available, your Siemens Service customer number. If repair work is necessary, please contact one of our service centres: Abu Dhabi ...0 26 42 38 00...
Care and maintenance Care and maintenance Your phone has been designed and manufactured to the highest of standards and should be treated with great care. The suggestions below will help you to enjoy your phone for many years. • Protect your phone from moisture and humidity! Precipitation, humidity and liquids contain min- erals that will corrode electronic...
Product data Declaration of conformity Siemens Information and Communi- cation mobile hereby declares that the phone described in this user guide is in compliance with the essential requirements and other rel- evant provisions of European Direc- tive 1999/5/EC (R&TTE). The declara- tion of conformity (DoC) concerned has been signed.
Alterna- tively, you can visit our online shop. Carrying Cases A range of carry cases is available at spe- cialist shops or you can visit the Siemens Mobile Store online: Original Siemens Accessories www.siemens-mobile.com/ shop...
The power is sup- plied via the cigarette lighter socket. Optional Car Kit accessories Car Data Adapter HKO-690 Phone-in adapter HKO-570 Products can be obtained in specialist shops or you can visit the Siemens Mobile Store online: Original Siemens Accessories www.siemens-mobile.com/ shop Accessories...
• In the case of new devices and their com- ponents exhibiting defects resulting from manufacturing and/or material faults with- in 24 months of purchase, Siemens shall, at its own option and free of charge, either replace the device with another device re- flecting the current state of the art, or re- pair the said device.
• In the case of new devices and their com- ponents exhibiting defects resulting from manufacturing and/or material faults within 24 months of purchase, Siemens shall, at its own option and free of charge, either re- place the device with another device re- flecting the current state of the art, or repair the said device.
Menu tree > Show entries Default book <New entry> Business card Groups Default book <Info numbers> > Calls missed Call records Calls received Calls dialled Delete records Durat/charges > URL/service provider Surf & fun Games Applications Downl. assis. Bookmarks Internet Camera >...
Menu tree > Inbox Messages > Draft > Unsent > Sent > MMS templates > SMS archive > Text modules > Msg settings > E-mail WAP push Retr. e-mail Send/rec. mail CB services > E-mail > E-mail Retr. e-mail Send/rec. mail >...
> Msg settings Messages > Calendar Organiser Appointments Tasks Notes Missed appts. Dictating mac Time zones Calend. setup > SIM services Extras Alarm clock Sound recorder Calculator Unit converter Stopwatch Countdown Remote sync. My stuff > Profiles Setup > Themes >...
Menu tree > Display Setup > Dynamic light > Ring tones > Call setup > Own greeting Big letters Illumination > Ringer setting Silent alert Volume Calls Group calls Other calls More melodies > Hide ID Call waiting Divert Call screening Any key answ.
> Setup Phone setup > Clock > Connectivity > Security > Key tones Info tones Automatic switch off Phone identity Memory assis. File system Master reset > Time/date Time zones Date format Time format Buddhist year Show clock Auto time zone >...
Menu tree > Security Setup > Network > Accessories > Barrings > Line Network info Choose netwrk Auto network Preferred net Band selection Fast search User group > Car Kit Key assignm. Headset > All outgoing Outgo internat Out.int.x home All incoming When roaming Status check...
0.59 W/kg**** The SAR information can also be found on the Siemens web site at www.siemens-mobile.com While there may be differences between the SAR levels of various phones and at various positions, all Siemens products meet the legal requirements.
SAR – European Union (RTTE) Further information: www.who.int/peh-emf www.mmfai.org www.siemens-mobile.com ** The CE mark confirms that the product is in compliance with the legal requirements of the European Union as a prerequisite for the placing on the market and the free move- ment of goods within the European internal market.
The highest SAR value for this model phone when tested for use at the ear 0,59 W/kg*** SAR information can also be found at www.siemens-mobile.com While there may be differences bet- ween the SAR levels of various pho- nes and at various positions, they all meet the international guidelines for safe RF exposure.
Index Index Accessories... 122 Additional books... 37 Addressbook Dial entry... 33 Groups ... 34 New entry... 31 Read entry ... 33 Aircraft mode ... 75 Alarm Alarm clock... 104 Type ... 100 Alarm clock ... 104 All calls (call time/charge) ... 39 All calls (diversion) ...
Codes... 17 Colour scheme ... 77 Conference... 27 Connection profiles ... 88 Contact list ... 62 Control code (DTMF) ... 29 Countdown ... 108 Credit limit ... 39 CSD settings ... 88 Customer care ... 118 Data connection ... 87 Date format...
Index Key tones ... 84 Language ... 77 Limit (call time/charge) ... 39 Logo... 77 Loss of phone, SIM card ... 121 Mailbox ... 60 Maintenance of phone... 120 Media Player... 110 Menu Controls... 14 My menu ... 95 Speed dialling ... 17 Menu speed dialling ...
Service tones... 84 Set time/date... 86 Settings... 74 Short message (SMS)... 43 Shown in the display ... 7 Shut down animation ... 78 Siemens City Portal ... 23 Signal strength ... 13 Silent alert... 80 SIM card Clear barring... 18 Insert... 9 Problems ...
Index Unanswered ... 82 Unit converter ... 106 Upper and lowercase letters... 19 User group ... 93 Validity, SMS ... 47 Voice message (mailbox) ... 60 Volume Handset volume... 24 Profiles ... 74 Ringtone... 80 Wallpaper (display) ... 77 WAP ... 69...