Maintenance - Makita DTD152 Instruction Manual

Hide thumbs Also See for DTD152:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1
Proper fastening torque for high tensile bolt
N•m
(kgf•cm)
160
(1632)
140
(1428)
120
(1224)
100
(1020)
80
(816)
60
(612)
40
(408)
20
(204)
0
1. Fastening time (second) 2. Fastening torque
Hold the tool firmly and place the point of the driver bit
in the screw head. Apply forward pressure to the tool to
the extent that the bit will not slip off the screw and turn
the tool on to start operation.
NOTICE:
If you use a spare battery to continue
the operation, rest the tool at least 15 min.
NOTE: Use the proper bit for the head of the screw/
bolt that you wish to use.
NOTE: When fastening M8 or smaller screw, carefully
adjust pressure on the switch trigger so that the screw
is not damaged.
NOTE: Hold the tool pointed straight at the screw.
NOTE: If the impact force is too strong or you tighten
the screw for a time longer than shown in the figures,
the screw or the point of the driver bit may be over-
stressed, stripped, damaged, etc. Before starting your
job, always perform a test operation to determine the
proper fastening time for your screw.
The fastening torque is affected by a wide variety of
factors including the following. After fastening, always
check the torque with a torque wrench.
1.
When the battery cartridge is discharged almost
completely, voltage will drop and the fastening
torque will be reduced.
2.
Driver bit or socket bit
Failure to use the correct size driver bit or socket
bit will cause a reduction in the fastening torque.
3.
Bolt
Even though the torque coefficient and the
class of bolt are the same, the proper fasten-
ing torque will differ according to the diame-
ter of bolt.
Even though the diameters of bolts are the
same, the proper fastening torque will differ
according to the torque coefficient, the class
of bolt and the bolt length.
4.
The manner of holding the tool or the material
of driving position to be fastened will affect the
torque.
5.
Operating the tool at low speed will cause a reduc-
tion in the fastening torque.
M12
M10
M8
1
2
1

MAINTENANCE

CAUTION:
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
M12
alcohol or the like. Discoloration, deformation or
cracks may result.
M10
Replacing carbon brushes
M8
► Fig.12: 1. Limit mark
3
Check the carbon brushes regularly.
Replace them when they wear down to the limit mark.
Keep the carbon brushes clean and free to slip in the
holders. All carbon brushes should be replaced at the
same time. Use only identical carbon brushes.
1.
Use a screwdriver to remove two screws then
remove the rear cover.
► Fig.13: 1. Rear cover 2. Screw
2.
Raise the arm part of the spring and then place
it in the recessed part of the housing with a slotted bit
screwdriver of slender shaft or the like.
► Fig.14: 1. Recessed part 2. Spring 3. Arm
3.
Use pliers to remove the carbon brush caps of
the carbon brushes. Take out the worn carbon brushes,
insert the new ones and replace the carbon brush caps
in reverse.
► Fig.15: 1. Carbon brush cap
4.
Make sure to place the lead wire in opposite side
of the arm.
► Fig.16: 1. Lead wire 2. Carbon brush cap
5.
Make sure that the carbon brush caps have fit into
the holes in brush holders securely.
► Fig.17: 1. Hole 2. Carbon brush cap
6.
Reinstall the rear cover and tighten two screws
securely.
7.
Insert the battery cartridge into the tool and break
in brushes by running tool with no load for about 1
minute.
8.
Check the tool while running and electric brake
operation when releasing the switch trigger. If electric
brake is not working well, ask Makita Authorized or
Factory Service Centers for repair.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
9 ENGLISH
Always be sure that the tool is
Never use gasoline, benzine, thinner,

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents