Table of Contents
Advertisement
Owner's Manual
18 V Cordless Drill
54-2902-4
CAUTION:
Before using this
cordless drill or any of
its accessories, read
this manual and follow
all Safety Rules and
Operating Instructions.
Imported by Trileaf Distribution Trifeuil Toronto, Canada M4S 2B8
Rev 1
08/06/06
General Safety Rules
Specific Safety Rules
and Symbols
Functional Description
Assembly
Operation
Maintenance
Accessories
Advertisement
Table of Contents
Related Manuals for jobmate 54-2902-4
Summary of Contents for jobmate 54-2902-4
- Page 1 Owner’s Manual 18 V Cordless Drill 54-2902-4 General Safety Rules CAUTION: Specific Safety Rules Before using this and Symbols cordless drill or any of Functional Description its accessories, read Assembly this manual and follow Operation all Safety Rules and ...
-
Page 2: Table Of Contents
21–23 WARRANTY 1-year Warranty This JobMate product carries a one (1) year warranty against defects in workmanship and materials. Trileaf Distribution agrees to replace the defective product free of charge with the same model or one of equal value or specification, within the stated warranty period, when returned by the original purchaser with proof of purchase. -
Page 3: Product Specifications
SPECIFICATIONS DRILL Chuck speeds …………….. 0–400/0–1150 RPM (no load) Gear box …...……………… 2 speed Battery ……………………... 18 V Clutch positions …………... 17 including drill mode Keyless chuck …………….. ” Weight ……………………... 7 lb. 14 oz. (3.6 kg) BATTERY & CHARGER Battery Voltage ……………... - Page 4 POWER TOOL SAFETY GENERAL SAFETY RULES Do not abuse the cord. Never use the cord to carry the tools or pull the plug from WARNING: Read and understand an outlet. Keep cord away from heat, oil, all instructions. Failure to follow all sharp edges or moving parts.
-
Page 5: Specific Safety Rules
POWER TOOL SAFETY Use safety equipment. Always wear eye Use only accessories that are protection. Dust mask, non-skid safety recommended by the manufacturer for shoes, hard hat or hearing protection must your model. Accessories that may be be used under applicable conditions. suitable for one tool may become hazardous when used on another tool. -
Page 6: Battery & Charger Safety
BATTERY & CHARGER SPECIFIC SAFETY RULES SAFETY Do not wear gloves, neckties or loose clothing. Do not store or carry battery in a manner Do not drill material too small to be in which metal objects could contact the securely held. exposed metal end. - Page 7 BATTERY & CHARGER SAFETY Use the charger only in a standard 110– 120 V 60 Hz electrical outlet. Charge the battery only with the charger supplied with the drill. Do not use the charger in wet or damp conditions. It is intended for indoor use only.
-
Page 8: Symbols
SYMBOLS WARNING: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. volts alternating or direct current amperes class II construction hertz... -
Page 9: Know Your Cordless Drill
KNOW YOUR CORDLESS DRILL On-board Spirit level screwdriver bit storage 3/8” Keyless Clutch chuck Forward / reverse switch Speed control switch Trigger switch Carry strap 18 V Battery pack Battery charger Charger wo speed stand gearbox... -
Page 10: Accessories
ACCESSORIES & CARTON CONTENTS AVAILABLE ACCESSORIES ACCESSORIES DESCRIPTION WARNING: Use only accessories High-speed steel bits: recommended for this cordless drill. 1/16", 5/64", 3/32", 7/64", Follow instructions that accompany 1/8", 9/64", 5/32", 11/64", accessories. Use of improper 3/16", 13/64", 7/32", 15/64", 1/4" accessories may cause injury to the Spade bits: operator or damage to the cordless drill. - Page 11 CARTON CONTENTS...
-
Page 12: Assembly & Operation
ASSEMBLY & OPERATION CHARGING THE 18 V BATTERY PACK Place the battery (1) in a dry location near a 110–120 V 60 Hz electrical outlet (see Fig. 1). Place the charger base (2) over the matching slots (3) of the battery. NOTE: Make sure the charger stand is pressed fully onto the battery until the battery latches (4) “click”... - Page 13 ASSEMBLY & OPERATION ON-BOARD SCREWDRIVER BIT STORAGE Convenient on-board screwdriver bit storage (1) is provided at the rear of the drill housing (Fig. 3). Fig. 4 FORWARD/REVERSE SWITCH The forward/reverse switch (1) is conveniently mounted above the trigger switch (2) (Fig.5). To make the drill rotate Fig.
- Page 14 ASSEMBLY & OPERATION TWO-SPEED GEARBOX – cont’d INSTALLING DRILL BITS WARNING: Never hold the chuck b) Use high-speed setting for drilling small body with one hand and use the drill holes. power to rotate the drill body to loosen c) Do NOT change the speed control or tighten bits.
- Page 15 ASSEMBLY & OPERATION ASSEMBLY & OPERATION INSTALLING DRILL BITS – cont’d WARNING Finish tightening the chuck jaws. Firmly Have you read “POWER TOOL grasp the chuck body with your hand SAFETY”, “SPECIFIC SAFETY and rotate it in a clockwise direction. RULES”, “BATTERY &...
- Page 16 ASSEMBLY & OPERATION DRILLING While holding the drill firmly, place the point of the drill bit at the point to be When drilling into smooth, hard surfaces drilled. Depress the switch trigger to such as metal, use a centre punch to mark start the drill.
- Page 17 ASSEMBLY & OPERATION DRIVING SCREWS – cont’d Select the correct screwdriver bit for the screw being driven. Fasten the screwdriver bit into the chuck, making sure the flats of the bit are gripped by the chuck jaws. Set the torque clutch to the appropriate Fig.
-
Page 18: Maintenance
ASSEMBLY & OPERATION MAINTENANCE GENERAL WARNING: When servicing, use only identical JobMate™ replacement parts. Use of any other part may create a hazard or cause product damage. DO NOT use solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged Fig. - Page 19 MAINTENANCE BATTERY MAINTENANCE BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING For power, long operational life and light weight your tool is powered by a Nickel- To preserve our natural resources, please cadmium battery pack. recycle or dispose of batteries properly. Nickel-cadmium batteries are powerful, This product contains nickel-cadmium rugged and will provide hundreds of...
- Page 20 MAINTENANCE HOW TO EXERCISE A NICKEL- CADMIUM BATTERY Every two months or after 30 charge/discharge cycles, whichever comes first, fully discharge your battery. To fully discharge the battery, place it in the tool that it came with and work with the tool until it nearly stops and no longer produces useful action.
-
Page 21: Parts & Service
PARTS DIAGRAM – MODEL 54-2902-4 Cordless Drill... - Page 22 PARTS LIST – MODEL 54-2902-4 Cordless Drill When servicing, use only JobMate™ replacement parts. Use of any WARNING: other parts may create a HAZARD or cause damage to your power tool. Any attempt to repair or replace electrical parts on this power tool may create a hazard unless repair is performed by a qualified technician.
- Page 23 PARTS LIST – MODEL 54-2902-4 Key # Part # Part Name Quantity 316829 Governor box 242562 Lever 315913 Timing point ring Self tapping screw 500006 ST2.9x12 201307 Removable gear ring 144008 Planetary bracket 200015 Planetary gear 144016 Planetary bracket 200016...
Need help?
Do you have a question about the 54-2902-4 and is the answer not in the manual?
Questions and answers