Do you have a question about the 80974 and is the answer not in the manual?
Questions and answers
Martin
July 6, 2025
Ahoj mám problém zo správnom zapojením poistkou pre auto Citroen Xsara hatchback 2.0hdj VTS packet 2000 neviem správne zapojiť poistky róby mi to velký problém
Page 1
T272 TRIMMER T272X TRIMMER Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing protection when operating this unit. Part Number 80974 Rev 11/04 T272 T272X WARNING!
If you have questions regarding your 272-series unit, or if you do not under- stand something in this manual, your Shindaiwa dealer will be glad to assist you. You may also contact Shindaiwa, Inc. at the address printed on the back of this manual.
General Safety Instructions WARNING! Never make unauthorized attachment installations. WARNING! Use Good Judgment ALWAYS wear eye protection to shield against thrown objects. NEVER operate the engine when transporting the unit. NEVER operate the engine indoors! Make sure there is always good ven- tilation.
New labels are avail- POSITION HANDLE able from your local authorized FORWARD OF THIS LINE Shindaiwa dealer. T272X Using the accompanying illustrations as a guide, familiarize yourself with your unit and its various compo- nents. Understanding your unit helps ensure top performance, long service life, and safer operation.
FC class 2-cycle mixing oil* * Shindaiwa One meets or exceeds these specifications and is recommended for all Shindaiwa Products ** The EPA emission compliance referred to on the emission compliance label located on the engine, indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements.
Page 6
Adjusting Throttle Level Free Play T272/T272X The throttle lever free play should be approximately 9/32 inch (7mm). See Figure 7. Make sure that the throttle lever operates smoothly without bind- ing. If it becomes necessar y to adjust the lever free play, follow the proce- dures and illustrations that follow.
Page 7
Figure 11 WARNING! A standard grass trimmer unit with loop handle should NEVER be operated with blade-type attachments. For blade use, the trimmer must be fitted with a bicycle-type handlebar or barrier bar that is located in front of the operator to reduce the risk of the operator coming in contact with the cutting attachment.
Assembly and Adjustments Installing a Blade T272X NOTE: The T272X is shipped with Holder “A,” the safety clip, Holder “B,” shaft bolt, and bolt guard installed. The shaft bolt is a LEFT- HAND THREAD AND IS REMOVED IN A CLOCKWISE ROTATION! 1.
FC classified oil and also meets or exceeds ISO-L-EGD performance requirements. Shindaiwa One is rec- ommended for use in all Shindaiwa low emissions engines. Shindaiwa One also in- cludes a fuel stabilizer. Examples of 50:1 mixing quantities ■ 1 gallon of gasoline to 2.6 oz.
If the idle speed cannot be adjusted by the pro- ceedure described here, have the unit inspected at an authorized Shindaiwa dealer. 1. Place the unit on the ground, then start the engine and allow it to idle for 2-3 minutes until warm.
Cutting Grass—Units equipped with a trimmer head. Your Shindaiwa T272 or T272X Grass Trimmer may be equipped with one of several Shindaiwa trimmer head models, each with features for spe- cific applications and/or operational...
Never strike or “slam” the spin- ning blade against the wood. n DO NOT use 2-tooth or non- Shindaiwa approved 4-tooth cutting blades with Shindaiwa trimmers and brushcutters. Brushcutter Handlebar A brushcutter’s handlebar helps prevent the operator from moving forward or the unit moving rear ward;...
ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA KOGYO CO., LTD. THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF...
Remove the filler plug from the side of the gearcase and press new grease into the gearcase until the old grease is pushed out. Use only lithium-base grease such as Shindaiwa Gear Case Lubricant or equivalent. See Figure 29. New Grease Grease...
Shindaiwa Tornado Blade To sharpen the cutters on a Shindaiwa Tornado Blade, use a 7/32-inch round file. File the leading edge of each tooth to a razor edge. The top plate of each tooth should angle back 30°.
These components are specifically listed below. Where a warrantable condition exists, Shindaiwa Kogyo Co., Ltd. will repair your small off-road engine at no cost to you including diagnosis, parts, and labor. Manufacturer’s Warranty Coverage When sold within the U.S., this...
Page 20
Fax: 503 692-6696 www.shindaiwa.com Shindaiwa Kogyo Co., Ltd. 6-2-11 Ozuka-Nishi Asaminami-Ku, Hiroshima 731-3167, Japan Telephone: 81-82-849-2220 Fax: 81-82-849-2481 2004 Shindaiwa, Inc. Part Number 80974 Revision 11/04 Shindaiwa is a registered trademark of Shindaiwa, Inc. Specifications subject to change without notice.
Page 26
2. Coloque los dos espaciadores y el soporte sobre el tubo exterior e instale sin ajustar los cuatro tornillos de ca- beza allen. Consulte la figura 8.
Page 27
Instalación del Cabezal de Nylon T272 1. Con el eje de salida de la caja de en- granajes cara arriba, gire el eje central y el soporte hasta que la muesca en el sujetador se alinie con la muesca en el borde de la caja de engranajes , y luego asegure el soporte a la caja de engranajes insertando el lado más largo de la llave hexagonal a través de...
Page 31
NOTA: A pesar de que el arnés no es requerida con el uso de podadoras, un arnés puede aumen- tar la comodiad para el operador durante periodos extensos de operación.
Page 34
8. Vuelva a ensamblar el silenciador en forma reversa al order de desemblaje.
Need help?
Do you have a question about the 80974 and is the answer not in the manual?
Questions and answers
Ahoj mám problém zo správnom zapojením poistkou pre auto Citroen Xsara hatchback 2.0hdj VTS packet 2000 neviem správne zapojiť poistky róby mi to velký problém