Download Print this page
Sharper Image SI857 Instructions Manual

Sharper Image SI857 Instructions Manual

Professional series ionic breeze quadra silent air purifier with ozoneguard

Advertisement

Professional Series™
Ionic Breeze
®
Quadra
®
Silent Air Purifier
with
OzoneGuard™
SI857 Instructions
Read and save these instructions.

Advertisement

loading

Summary of Contents for Sharper Image SI857

  • Page 1 Professional Series™ Ionic Breeze ® Quadra ® Silent Air Purifier with OzoneGuard™ SI857 Instructions Read and save these instructions.
  • Page 4: Table Of Contents

    Table of Contents Warnings ...5 Important Information - Please Read ...7 Frequently Asked Questions about OzoneGuard™ ...8 Setup and Operation ...9 Cleaning the Collection Grid ...11 Thorough Cleaning ...12 Additional Information ...13 Statement of FCC Compliance ...14...
  • Page 5: Warnings

    Warning: To reduce the risk of fire, electric shock, or injury when using any electrical appliance, basic precautions should always be observed, including the following: • This appliance operates at 110V AC and 50Hz or 60Hz only. • Connect to a properly grounded outlet only. •...
  • Page 6 • Do not pull, lift or carry by the power cord. Do not use the cord as a handle, close a door on the cord, or pull the cord around or against sharp edges or corners. • Keep the cord away from heated surfaces. •...
  • Page 7: Important Information - Please Read

    Important Information – Please Read The collection grid has many edges and areas that can trap water. Ensure the grid is completely dry before re-inserting it into the unit. If it is not completely dry, the unit could be damaged. If water is used to clean the grid, please allow at least 24 hours for the collection grid to dry.
  • Page 8: Frequently Asked Questions About Ozoneguard

    Frequently Asked Questions about OzoneGuard™ What does OzoneGuard™ do? With the OzoneGuard in place, a significant portion of ground- level ozone inside the air purifier — including any trace levels of ozone by-product — is converted into oxygen before the cleaned air circulates back into the room.
  • Page 9: Setup And Operation

    Setup and Operation To reduce the risk of electric shock, this equipment has a ground- ing-type plug that has a third (grounding) pin. This plug will only fit into a grounding-type power outlet. If the plug does not fit into the outlet, contact qualified personnel to install the proper outlet.
  • Page 10 Setup and Operation Normal operation at all power Mode Control levels involves a programmed cycle of altering high and low air movement. To override the power control setting and let the unit run at maximum power for five minutes, Boost/Ions press BOOST/IONS until the button turns blue.
  • Page 11: Cleaning The Collection Grid

    Cleaning the Collection Grid Clean the grid every one or two weeks. As a reminder, the clean- ing indicator light will turn green after two weeks. If the cleaning indicator light turns red, the unit has shut down because of exces- sive dirt or circuitry problems.
  • Page 12: Thorough Cleaning

    Thorough Cleaning If the unit makes noise during operation, a thorough cleaning of the grid, grills and internal ionizing wires may be required. Unplug the unit before cleaning. Release the OzoneGuard front grill and back grill by lifting the blue release tabs on the bottom of the grills.
  • Page 13: Additional Information

    The exterior of the unit can be cleaned using a cloth or sponge and a solution of one part household bleach to five parts water or any bleach-based spray cleaner. Before plugging the unit back into an outlet, allow the surface to dry completely.
  • Page 14: Statement Of Fcc Compliance

    Statement of FCC Compliance — Model SI857 WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 15 Statement of FCC Compliance — Model SI857 •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Page 16 What The Sharper Image Will Do The Sharper Image will repair any defects in materials or workmanship. In the event repair is not possible, The Sharper Image will either replace this product with one of similar features and price, or refund the full purchase price of the product, whichever you prefer.