Table of Contents
Advertisement
MODEL
HT-SB250(BK)
SOUND BAR SYSTEM
ww. b ar c odesof t . c om
e Symbol o gy: Code 93 ; Font Facename: Code93 M H r
Encode: TI N SZA877AWZZ
WOW HD technology is incorporated under license from SRS Labs, Inc.
Note: This product is recommended for flat panel TV (LCD and plasma).
Accessories
ze 8 :
*TINSZA877AWZZFP*|
Please confirm that only the following accessories are included.
Remote control x 1
(RRMCGA235AWSA)
Wall mount angle x 2
ze 10 :
*TINSZA877AWZZFP*|
(LANGKA167AWFW)
TINSZA877AWZZ
OPERATION MANUAL
is a trademark of SRS Labs, Inc.
RCA cable
AC/DC adaptor x 1
(2 pins - 2 pins) x 1
(RADPAA061AWZZ)
(QCNWGA041AWPZ)
Foot cushion x 4
(PCUSSA118AWZZ)
(TCAUHA022AWZZ)
AC power cord x 1
(QACCDA005AWZZ)
( Spike + Nut ) x 4
Pattern paper x 1
(CLEGMA005AW02,
Length: 25 mm)
ENGLISH
Nut
Printed in Malaysia
10M R AS
1
Advertisement
Table of Contents
Related Manuals for Sharp HTSB250
Summary of Contents for Sharp HTSB250
- Page 1 MODEL HT-SB250(BK) SOUND BAR SYSTEM Encode: TI N SZA877AWZZ is a trademark of SRS Labs, Inc. WOW HD technology is incorporated under license from SRS Labs, Inc. Note: This product is recommended for flat panel TV (LCD and plasma). Accessories *TINSZA877AWZZFP*| Please confirm that only the following accessories are included.
-
Page 2: Special Notes
Special notes CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Explanation of Graphical Symbols: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage”... - Page 3 IMPORTANT SAFETY INSTRUCTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire.
- Page 4 IMPORTANT SAFETY INSTRUCTIONS (continued) If the product does not operate normally by following the operating instructions. Adjust controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, If the product has been dropped or...
-
Page 5: For U.s. Customer Only
Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. -
Page 6: Controls And Indicators
SHARP will not be held responsible Controls and indicators 12 13 for any damage resulting from use of this unit with a voltage other than that which is specified. -
Page 7: Rear Panel
Volume Up and Turn up/down the TV Down Buttons volume. Note: ● Some models of SHARP TV may not be operable. ● SHARP TV remote control will not work with HT-SB250(BK) system. Rear Panel ■ Audio Line In 2 Jack ...9 Line In Jacks ...9... -
Page 8: System Preparation
SHARP is not responsible for accidents ● resulting from improper installation. Driving screws ■ SHARP designed the units so you may hang them on the wall. Use proper screws (not supplied). See below for size and type. 3/16” (5 mm) Min. -
Page 9: Placing The Sound Bar
System preparation (continued) Make a hole on the wall following the screw point marks on the pattern paper by using a drill. 1-1/4” (32 mm) 3/8” (8-9 mm) Wall surface Fix a wall mount plug into the hole using a hammer, until it is flush with the wall surface. -
Page 10: Falling Prevention
Falling prevention Sound bar connections to TVs Caution: Turn off all other equipment before making any connections. Tuner receiving for other audio system Placing the antenna near the unit AC ● power cord may cause noise pick up. Place the antenna away from the unit for better reception. -
Page 11: Ac Power Connection
AC power connection After checking all the connections have been made correctly, connect the AC power cord to the AC power input jack, then to the AC outlet. Using with the AC/DC ■ adaptor 1 Plug the AC power cord into the AC/DC adaptor. -
Page 12: General Control
Remote control (continued) shall not be exposed to excessive heat such as sunshine, fire or the like. Installing the battery incorrectly may cause ● the unit to malfunction. Notes concerning use: Replace the battery if the operating distance ● is reduced or if the operation becomes erratic. -
Page 13: Bass Control
General control (continued) Remote control operation: Press the VOLUME + button to increase the volume and the VOLUME – button to decrease the volume. Muting ■ The volume is muted temporarily when pressing the MUTE button on the remote control. Press again to restore the volume. -
Page 14: Troubleshooting Chart
Many potential problems can be resolved by the owner without calling a service technician. If something is wrong with this product, check the following before calling your authorized SHARP dealer or service center. General ■ Symptom Possible cause No sound is Is the input signal ●... -
Page 15: Maintenance
Troubleshooting chart (continued) Condensation ■ Sudden temperature changes, storage or operation in an extremely humid environment may cause condensation inside the cabinet or on the transmitter on the remote control. Condensation can cause the unit to malfunc- tion. If this happens, leave the power on until normal playback is possible (about 1 hour). -
Page 16: Error Indicators And Warnings
Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specifica- tion figures indicated are nominal values of production unit. There may be some deviations from these values in individual unit.