Sharp Notevision PG-B10S Operation Manual

Sharp lcd projector pg-b10s operation manual.
Hide thumbs

   Related Manuals for Sharp Notevision PG-B10S

   Summary of Contents for Sharp Notevision PG-B10S

  • Page 1


  • Page 2

    For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories”...

  • Page 3

    SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 5A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked above, which is also indicated on the pin face of the plug, must be used.

  • Page 4

    De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds, Spaans, Italiaans, Nederlands, Portugees, Chinees (Traditioneel Chinees en Vereenvoudigd Chinees) en Koreaans. Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt. O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Sueco, Espanhol, Italiano, Holandês, Português, Chinês, (Chinês Tradicional e Chinês Simplificado) e Coreano.

  • Page 5

    2. CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

  • Page 6: Product Disposal

    United States of America, the Electronic Industries Alliance: . This SHARP projector uses an LCD (Liquid Crystal Display) panel. This very sophisticated panel contains 480,000 pixels ( RGB) TFTs (Thin Film Transistors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to.

  • Page 7: How To Read This Operation Manual

    Using the Menu Screen The menu screens allow you to adjust the image and various projector settings. The menu can be operated to achieve two functions, adjustment and setting. (For adjusting the menu items, see pages Example: “Picture”...

  • Page 8: Table Of Contents

    Turning off the Sound Temporarily ... 20 Correcting Trapezoidal Distortion ... 20 Turning the Power off (Putting the Projector into the Standby Mode) ... 21 Adjusting the Lens ... 22 Using the Adjustment Feet ... 23 Variable Lens Shift Feature ... 24 Adjusting the Projected Image Position ...

  • Page 9: Table Of Contents

    Resetting the Lamp Timer ... 67 Connecting Pin Assignments ... 68 RS-232C Specifications and Command Settings ... 69 Computer Compatibility Chart ... 70 Troubleshooting ... 71 For SHARP Assistance ... 73 Specifications ... 74 Dimensions ... 75 Glossary ... 76 Index ... 77...

  • Page 10: Important Safeguards

    IMPORTANT SAFEGUARDS CAUTION : Please read all of these instructions before you operate this product and save these instructions for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS.

  • Page 11: Be Sure To Read The Following Safeguards When Setting Up Your Projector

    Caution concerning the setup of the projector I For minimal servicing and to maintain high image qual- ity, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the lens must be cleaned more often.

  • Page 12: How To Access The Pdf Operation Manuals

    PDF operation manuals in several languages are included in the CD-ROM, so that you can work with the projector, even if you do not have this manual. To utilize these manuals, you need to install Adobe Acrobat Reader on your PC (Windows or Macintosh). If you have not installed Acrobat Reader yet, you can install it from the CD-ROM.

  • Page 13: Accessories, Supplied Accessories, Optional Accessories

    I RS-232C serial control cable (32'10" (10.0 m)) I Remote receiver Note Some of the cables may not be available depending on the region. Please check with your nearest Sharp Authorized Projector Dealer or Service Center. Two R-6 batteries (“AA” size, UM/SUM-3, HP-7 or similar) For U.K., Hong Kong and...

  • Page 14: Part Names, Projector (front And Top View)

    Projector (Front and Top View) ON button For turning the power on. Power indicator STANDBY button For putting the projector into the standby mode. Lamp indicator Temperature warning indicator AUTO SYNC button...

  • Page 15: About The Indicators On The Projector, Power Indicator, Lamp Indicator, Temperature Warning Indicator

    About the Indicators on the Projector Attaching and Removing the Lens Shipping Block When attaching the lens shipping block, be sure to return the lens shift lever to the center position. If the lens is shifted upward or downward, the lens shipping block cannot be attached.

  • Page 16: Projector (rear View)

    Using the Kensington Lock This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector.

  • Page 17: Input/output Terminals And Connectable Main Equipment

    INPUT/OUTPUT Terminals and Connectable Main Equipment RS-232C terminal INPUT 1 terminal Connecting the Connecting the computer. computer to control the (See page 51.) projector. Connecting video equipment (See page 54.) with component output terminal (DVD player, DTV decoder, etc.). (See page 53.) RGB OUTPUT terminal...

  • Page 18: Remote Control (front View)

    Part Names Numbers in refer to the main pages in this operation manual where the topic is explained. Remote Control (Front View) STANDBY button For putting the projector into the standby mode. KEYSTONE button For entering the Keystone Correction mode.

  • Page 19: Using The Remote Control, Usable Range, Inserting The Batteries

    Battery fluid from leaked batteries is harmful to skin, therefore be sure to first wipe them and then remove them using a cloth. The batteries included with this projector may run down in a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries.

  • Page 20: Setup And Projection, Projection

    Setup and Projection In this section, connection of the projector and the computer is explained as an example. Place the projector facing a wall or a screen Connect the projector to the computer and plug the power cord into the AC socket of the projector...

  • Page 21: Adjust The Projected Image

    Correcting trapezoidal distortion using the Keystone Correction. On the projector On the remote control Select the INPUT mode Select the “INPUT 1” using the INPUT button on the projector or the INPUT 1 button on the remote control. On the On the remote projector control...

  • Page 22: Image Projection, Turning The Projector On

    Green: The lamp is ready. Blinking in green: The lamp is warming up. Red: The lamp should be replaced. If the projector is put into the standby mode and immediately turned on again, the lamp indicator may take some time to illuminate.

  • Page 23: Switching The Input Mode, Adjusting The Volume

    Note When no signal is received, “NO SIGNAL” will be displayed. When a signal that the projector is not preset to receive is received, “NOT REG.” will be displayed. The INPUT mode is not displayed when “OSD Display” of the “Options” menu is set to “OFF”.

  • Page 24: Displaying The Black Screen And Turning Off The Sound Temporarily, Correcting Trapezoidal Distortion

    26)). The Keystone Correction cannot be ad- justed in the lateral direction. Press to enter the Key- stone Correction mode. You can also use on the projector. AV MUTE button KEYSTONE button UNDO button "On-screen display (Keystone Correction mode) "...

  • Page 25

    Info Do not unplug the power cord during pro- jection or cooling fan operation. The cool- ing fan in this projector continues to run for about 90 seconds after the projector enters the standby mode. This can cause damage due to rise in internal tempera- ture, as the cooling fan also stops.

  • Page 26: Adjusting The Lens, Focus Ring, Zoom Knob

    Image Projection Adjusting the Lens The image is focused and adjusted to the de- sired size using the focus ring or zoom knob on the projector. Adjust the focus by rotating the focus ring. Adjust zooming by moving the zoom knob.

  • Page 27: Using The Adjustment Feet

    Using the Adjustment Feet The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector. When the screen is in a higher position than the projector, the projection image can be made higher by adjusting the projector.

  • Page 28

    (360°) to adjust the projection position simply by moving the lens shift lever on the front of the projector. This is a useful function in cases such as when the screen can not be moved.

  • Page 29: Adjusting The Projected Image Position

    Adjust the projected image position using the lens shift lever. Info When using the projector (during projec- tion), be sure not to subject the projector to any impact. If the projector is subjected to impact, the projection image may deviate from the adjusted position.

  • Page 30: Resize Mode, Switching The Resize Mode

    Resize Mode This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose “NORMAL”, “DOT BY DOT”, “BORDER” or “STRETCH” image. Switching the Resize Mode Press Pressing changes the display as shown on pages and 27.

  • Page 31

    VIDEO 480I, 480P, 4:3 aspect ratio. NTSC, PAL, SECAM Letter box, squeeze 540P, 720P, 1080I 16:9 aspect ratio “STRETCH” is fixed when 540P, 720P or 1080 Input Signal DVD / Video Image type 4:3 aspect ratio Letter box 480I, 480P, NTSC, PAL, SECAM Squeezed 16:9 image Squeezed 4:3 image...

  • Page 32: Freeze And Enlarge Image, Freezing A Moving Image, Displaying An Enlarged Portion Of An Image

    Freeze and Enlarge Image You can instantly freeze a moving image and enlarge a specific portion of an image with the remote control. Using these functions, you can explain the image to the audience more effectively. UNDO button Freezing a Moving Image Press The projected image is frozen.

  • Page 33: Keylock Function, Locking The Operation Buttons, Taking The Keylock Off

    Keylock Function Use this function to lock the operation buttons on the projector. Locking the Operation Buttons Hold down on the projector for about 3 seconds while the projector is being turned on. Note The keylock function does not affect the opera- tion with the remote control buttons.

  • Page 34: Menu Items

    When using the INPUT 1 mode: In the “Picture” menu of INPUT 1, “Color”, “Tint” and “Sharp” are only displayed when “Signal Type” is set to “Component” or set to “Auto” and the input signal is recognized as a component signal.

  • Page 35

    Français Italiano Svenska Português PRJ Mode Front Rear Page Sub menu Auto NTSC3.58 SECAM NTSC4.43 PAL-M PAL-N PAL-60 Sharp Blue None Center Upper Right Lower Right Upper Left Lower Left Old Password New Password Reconfirm Old Code New Code Reconfirm...

  • Page 36: Using The Menu Screen, Menu Selections (adjustments)

    Using the Menu Screen The menu screens allow you to adjust the image and various projector settings. The menu can be operated to achieve two functions, adjustment and setting. (For adjusting the menu items, see pages Example: “Picture” menu screen for...

  • Page 37

    Press ' ' ' or " " " to select the item " " you want to adjust. The selected item is highlighted. Note To display a single adjustment item, press after selecting the item. Only the selected adjustment item will be displayed.

  • Page 38: Menu Selections (settings)

    Menu Selections (Settings) The following procedure is the operating method in a setting menu. This operation can also be performed by using the buttons on the projector. Press The “Picture” menu screen for the se- lected input mode is displayed. Note...

  • Page 39

    ' ' or " " " " " to select the Press ' item you want to set, and then press | | | | | to display the sub menu. The selected item is highlighted. When you select “Password” or “Anti- Theft”...

  • Page 40: Picture Adjustment, Adjusting The Image

    Picture Adjustment You can adjust the projector’s picture to your preferences using the “Picture” menu. Adjusting the Image Select the item on the “Picture” menu and adjust the image. Adjusting the menu screen Example: “Picture” screen menu for INPUT 1 (RGB) mode...

  • Page 41: Gamma (gamma Correction), Srgb (srgb Setting)

    Gamma (Gamma Correction) Gamma is an image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the bright- ness of the brighter portions. When you are displaying images with frequent dark scenes, such as a film or concert, or when you are displaying images in a bright room, this feature makes the dark scenes easier to see and gives the...

  • Page 42: Memory (storing And Selecting The Adjustment Settings)

    Picture Adjustment Signal Type (Signal Type Setting) The signal type setting is preset to “Auto”; however, in rare cases a clear picture may not be displayed. In that case, select “RGB” or “Com- ponent” in accordance with the input signal. Select “Signal Type”...

  • Page 43: Computer Image Adjustment, Adjusting The Computer Image

    Computer Image Adjustment Using the “Fine Sync” menu, you can adjust the computer image, match the computer dis- play mode, and check the input signal. Adjusting the Computer Image When “Auto Sync” is set to OFF or when vertical stripes or flickering occur in portions of the screen even if “Auto Sync”...

  • Page 44

    INPUT 1 mode Description of Auto Sync Adjustment Selectable Settings Description Auto Sync adjustment will occur when the projector is turned on or when the input signals are switched, when connected to a computer. Auto Sync adjustment is not automati- cally performed.

  • Page 45: Using The "options" Menu, Lamp Timer (life)

    Using the “Options” Menu You can use the “Options” menu to enhance the usage for the projector. Lamp Timer (Life) ing the Lamp Life Status) You can confirm the cumulative lamp usage time and the remaining lamp life (percentage). Display the “Options” menu to check the lamp life status.

  • Page 46

    Sharp Blue None Note • If the input signal has interference, the screen will be displayed during interference. (Selecting a Page INPUT 2 (S-Video) mode Sharp Blue None Description of Background Images Description SHARP default image Blue screen Black screen...

  • Page 47

    Power Off Function) When no input signal is detected for more than ” (Standard 15 minutes, the projector will automatically en- ter the standby mode if set to “ The Auto Power Off function will be disabled if it has been set to “...

  • Page 48: Menu Color

    Using the “Options” Menu Menu Position the Menu Screen Position) Select “Menu Position” on the “Options” menu and the desired position for the menu screen. Setting the menu screen Page Example: “Options” menu screen for INPUT 2 (S-Video) mode Description of Menu Positions Selectable settings Description Center...

  • Page 49: If You Forget Your Password

    The password cannot be deleted using the above described procedures while the “Anti-Theft” function is set. If you forget your password while the “Anti-Theft” function is activated, you will need to contact your nearest Sharp Autho- rized Projector Dealer or Service Center (see page 73). You may need to bring your projector to them to restore the projector to original factory condition (password and keycode reset).

  • Page 50

    If you lose or forget your keycode, you will need to contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 73). You may need to bring your projector to them to restore the projector to original factory condition (password and keycode reset).

  • Page 51

    Note When “Anti-Theft” is selected, the keycode in- put box will appear. If no keycode is entered, the image will not be displayed, even if the projector receives the in- put signal. Press on the remote control or on the projector to turn on the projector.

  • Page 52: Using The "language" Menu, Selecting The On-screen Display Language

    Using the “Language” Menu Selecting the On-screen Display Language The on-screen display language of the projector can be set to English, German, Spanish, Dutch, French, Italian, Swedish, Portuguese, Chinese, Korean or Japanese. Display the “Language” menu and select the desired language as the on-screen display.

  • Page 53: Using The "prj Mode" Menu, Reversing The Projected Image

    The “PRJ Mode” menu will disappear. Note This function is used for the reversed image setup. See page for this setup. This procedure can also be performed by using the buttons on the projector. ENTER button MENU button ', ", \, | buttons...

  • Page 54: Connecting The Projector To Other Devices, Before Connecting, This Projector Can Be Connected To

    Before Connecting Note Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off the devices to be connected. After making all connections, turn on the projector and then the other devices.

  • Page 55: Connecting The Projector To A Computer

    I This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC compatible computer will communicate their setting requirements, allowing for quick and easy setup. I Before using the “Plug and Play” function, be sure to turn on the projector first and the connected computer last.

  • Page 56: Connecting To Video Equipment

    To view a higher- quality image, use a commercially available S-video cable to connect the INPUT 2 termi- nal on the projector and the S-video output terminal on the video equipment. A ø3.5 mm minijack to RCA audio cable (com- mercially available) is required for audio input.

  • Page 57: Connecting To Component Video Equipment

    ø3.5 mm minijack to RCA audio cable (commercially available). Note If the projector does not automatically de- tect a COMPONENT signal, the projected image will appear distorted. To correct, change the menu setting from “Auto” to “Component”.

  • Page 58: Controlling The Projector Using A Computer

    RS-232C adaptor (sold separately) and an RS- 232C serial control cable (cross type, sold separately), the computer can be used to con- trol the projector and check the status of the projector. See page for details. Connect a DIN-D-sub RS-232C...

  • Page 59: Connecting To A Monitor, Connecting The Power Cord To The Projector

    For this connection, computer RGB cable (sold separately) is required. Connecting the Power Cord to the Projector Connecting the Power Cord Plug the supplied power cord into the AC socket on the rear of the projector. Supplied accessory Computer RGB cable Optional AN-C10BM cable (32'10"...

  • Page 60: Setting Up The Screen

    Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image. Note The projector lens should be centered in the middle of the screen. If the horizontal line passing through the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.

  • Page 61: Screen Size And Projection Distance

    Screen Size and Projection Distance NORMAL Mode (4:3) Picture (Screen) size Diag. [ ] Width Height 300" (762 cm) 610 cm (240”) 457 cm (180") 250" (635 cm) 508 cm (200") 381 cm (150") 200" (508 cm) 406 cm (160") 305 cm (120") 150"...

  • Page 62: Projecting A Reversed Image, Projection From Behind The Screen, Projection Using A Mirror

    Ceiling-mount Setup I It is recommended that you use the optional Sharp ceiling- mount bracket for this installation. Before mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain the recommended ceiling-mount bracket (sold separately).

  • Page 63: Carrying The Projector, How To Use The Carrying Case

    Sending the projector in the carrying case as a parcel may cause damage to the pro- jector. If you send the projector in the car- rying case as a parcel, be sure to place it in a sturdy case and with enough shock absorbing material to avoid any damage.

  • Page 64: Maintenance

    Do not attach rubber or plastic items to the projec- tor for a long time. The effects of some of the agents in the plastic may cause damage to the quality or finish of the projector. Thinner I Wipe off dirt gently with a soft flannel cloth.

  • Page 65: Replacing The Air Filter, Cleaning And Replacing The Air Filter

    100 hours of use. Clean the filters more often when the projector is used in a dusty or smoky location. • Ask your nearest Sharp Authorized Pro- jector Dealer or Service Center to ex- change the filter (PFILDA010WJZZ) when it is no longer possible to clean.

  • Page 66

    Replacing the Air Filter Remove the air filter. Pick the air filter up with your fingers and lift it out of the filter cover. Clean the air filter. Clean the dust off the air filter and cover with a vacuum cleaner extension hose. Replace the air filter.

  • Page 67: Maintenance Indicators

    I The warning lights on the projector indicate problems inside the projector. I If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter the standby mode. After the projector has entered the standby mode, follow the procedures given below.

  • Page 68

    In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again. If you want to clean the air vents during projector operation, be sure to put the projector into the standby mode. After the cooling fan has stopped, clean the vents.

  • Page 69: Regarding The Lamp, Lamp, Caution Concerning The Lamp, Replacing The Lamp

    Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit. I If the new lamp does not light after replacement, take your projector to the nearest Sharp Autho- rized Projector Dealer or Service Center for repair. Purchase a replacement lamp unit of type BQC- PGB10S//1 from your nearest Sharp Authorized Projector Dealer or Service Center.

  • Page 70: Removing And Installing The Lamp Unit

    Wait until the cooling fan stops. Warning! Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or injury. Disconnect the power cord. Unplug the power cord from the AC socket.

  • Page 71: Resetting The Lamp Timer, Ac Socket

    Connect the power cord. Plug the power cord into the AC socket of the projector. Reset the lamp timer. While simultaneously holding down on the projector, press on the projector. “LAMP 0000H” is displayed, indicating that the lamp timer is reset. Info Make sure to reset the lamp timer only when replacing the lamp.

  • Page 72: Connecting Pin Assignments

    RS-232C Terminal: 9-pin Mini DIN female connector DIN-D-sub RS-232C adaptor: 9-pin D-sub male connector Note Pin 8 (CS) and Pin 7 (RS) are short circuited inside the projector. RS-232C Cable recommended connection: 9-pin D-sub female connector Note Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling device (e.g.

  • Page 73: Rs-232c Specifications And Command Settings

    RS-232C Specifications and Command Settings PC control A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, sold separately) to the projector. (See page Communication conditions Set the serial port settings of the computer to match that of the table.

  • Page 74: Computer Compatibility Chart

    Compatible with sync on green signal SXGA+, SXGA and XGA compatible in Intelligent Compression and Expansion System resizing technology The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards. Horizontal Frequency...

  • Page 75: Troubleshooting

    Troubleshooting Problem Projector power cord is not plugged into the wall outlet. Power to the external connected devices is off. The selected input mode is wrong. The AV MUTE function is working. Cables incorrectly connected to rear panel of the projector.

  • Page 76

    Troubleshooting Problem Picture is green on Change the input signal type setting. INPUT 1 COMPONENT. Picture is pink (no green) on INPUT 1 RGB. Picture is dark. The lamp indicator is illuminating in red. Replace the lamp. Picture is too bright and Picture adjustments are incorrectly set.

  • Page 77: For Sharp Assistance

    For SHARP Assistance If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages your question, please contact the SHARP Service departments listed below. U.S.A. Sharp Electronics Corporation 1-888-GO-SHARP (1-888-467-4277)

  • Page 78: Specifications

    (UDSKAA039WJZZ), “QUICK GUIDE” label (TLABZA439WJZZ), Operation manual (TINS- A917WJZZ) As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

  • Page 79: Dimensions

    Dimensions Units: inches (mm) Side View Front View Bottom View Rear View Top View (294) (64) ø 65 (60.4) (195.6) (64.2) (207.4) (86.6) (28.5) (65) (45) Side View...

  • Page 80: Glossary, Lens Shift, Aspect Ratio, Clr Temp (color Temperature), Keystone Correction

    Glossary Anti-Theft If the “Keycode” set in the projector is not correctly entered, the projector will not operate even if sig- nals are entered. Aspect Ratio Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4:3.

  • Page 81: Auto Sync (auto Sync Adjustment), Index

    Replacing the lamp ... 65 RESIZE button ... 26 RGB cable ... 51 RGB OUTPUT terminal ... 55 RS-232C terminal ... 54 Sharp ... 36 Signal Info ... 40 Signal Type ... 38 Special Modes ... 39 sRGB ... 37 STANDBY button ...

  • Page 82


Comments to this Manuals

Symbols: 0
Latest comments: