Kärcher SB MB Manual
  1. Manuals
  2. Brands
  3. Kärcher Manuals
  4. Pressure Washer
  5. SB MB
  6. Manual

Kärcher SB MB Manual

Hide thumbs Also See for SB MB:
Table of Contents

Advertisement

Quick Links

SB MB
59638780 04/17

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SB MB and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Kärcher SB MB

Summary of Contents for Kärcher SB MB

  • Page 1 SB MB 59638780 04/17...

  • Page 3: Table Of Contents

    Please read and comply with DANGER Environmental protection these original instructions prior Risk of burns due to hot exhaust gases; to the initial operation of your appliance and hence, do not reach over the exhaust open- The packaging materials are re- store them for later use or subsequent own- ing.

  • Page 4: Operation

    – Installation of gas pipes - especially the Behaviour in emergency situations Workstation gas connections to the machine - – Coins are thrown in at the control panel should only be done by a technical and the washing programme is select- company that has been approved by the Industrial Association for Gas and –...
  • Page 5 Foam Wash Washing time Operations procedure Deep cleaning with active foam. – Washing time starts after the coin is Only use foam brush when the programme thrown in. is running and after the high-pressure – The remaining value display shows the wash.

  • Page 6: Open The System

    Open the system 1 Coin acceptor door lock only for SB MB Comfort 2 Coin cassette lock (optional) only for SB MB Comfort 3 Unlock the coin acceptor door Only for SB MB standard Pull down to unlock. 4 Front door unlock Lift up to unlock.

  • Page 7: Settings

    1 Dry foam station Adjust compressor Setting dosing pumps 2 Display of control (in control cabinet) 3 Display of control Only for SB MB standard 4 Control board 5 Main switch 6 Dosing pump, dry foam station 7 Hot air blower...
  • Page 8 Basic adjustment Wheel cleaner/intensive foam (option) 1 Dosing pump for dry foam Basic setting water 1 Ventilation lever 2 Ventilation button  Open fresh water supply. 1 Input of detergent 3 Adjustment knob dosing volume  Use wash programme "Foam wash" at 2 Nozzle insert a washing area.
  • Page 9 (example). ATTENTION Controls If more than one maintenance procedure is Risk of damage due to acidic detergents. SB MB standard required, these will be shown in sequence. Only use alkaline detergents for wheel If no maintenance procedures are required, cleaning.
  • Page 10 1 Menu item 2 Parameter...
  • Page 11 Select the parameter you want to set Date / Time  Select the menu item with the buttons Setting date, time and summer/winter time LEFT and RIGHT. change  Press OK to open the parameter group. Auto summer / winter time = YES: T2 applies to weekdays marked with an "*".
  • Page 12  Switch on the frost protection pump 2 Thermostat (see Chapter "Manual procedures").  Adjust the pressure reducer so that at Hot air ventilator SB MB least 0.5 l/min of water flows from each Hot air blower hand spray gun.

  • Page 13: Filling In Detergents

    Filling in detergents Manual interventions Refill fuel DANGER  In normal operating mode, press the Risk of fire. Observe local regulations for "OK" key on the control longer than 2 handling fuels. seconds. Do not use unsuitable fuels, as they may be dangerous.

  • Page 14: Sales Indicator

    Changing the password Note: Press "ESC" to cancel the change of the password. When the "OK" key is pressed, the circula- Total sales since start-up of the washing Upon the initial start-up, the password is tion pump activates frost protection for 3 system.
  • Page 15 Heating ABS heating oil With temperatures below 3°C, check if the trace heating of the heat- Operator tank (option) ing oil line between the heating oil tank and SB MB is warm. monthly or af- opinion Quantity of frost water pro- Target value: approx.

  • Page 16: Shutting Down

    Shutting down  Turn the main switch to position "0" Shutdown during Frost Conditions  Turn the main switch to position "1".  Lock the operating time at the control.  Filling the fuel tank. Shutdown If the equipment is to be shut down, and there is not danger of frost, ...

  • Page 17: Function

    1 Fine filter for fresh water (80-100 μm, 29 Bypass valve semi load with throttle, option) only for high pressure module type 908 * Only for SB MB standard 2 Locking valve for fresh water 30 High pressure pump 3 Locking water for fresh water for soften-...
  • Page 18 18 Locking valve for permeate tank 41 Suction hose for detergent 19 Buffer tank for permeate 42 Detergent filter, foot valve * Only for SB MB standard 20 Pressure switch for RO water shortage 43 Solenoid valve for warm water 21 Manometer working pressure...
  • Page 19 Attachment kit disconnection from mains (optional) 1 Fine filter for fresh water (80-100 μm, option) 2 Pump attachment kit disconnection from mains (optional) 3 Swimmer tank for cold water...
  • Page 20 Wheel cleaner/intensive foam (option) A Rim cleaner Micro emulsion (option) Frost protection 1-tool (option, SB- B Intensive foam MB 2 pump Fp only) C Node piece 1 Swimmer valve 2 Manometer 3 Detergent solution (water + detergent) 4 Pump for detergent solution 5 Cleaning agent container 6 Injector 7 Sieve...
  • Page 21 Frost protection 2-tool, wet foam 4. Type of water (option, SB-MB 2 pump Fp only) A 4. Type of water B Fresh water C Softened water, warm D Permeate E to high-pressure pump 1 Temperature sensor (option) 2 Drain valve float container warm water 1 Washing brush 2 Backflow valve with throttle and sieve 3 Solenoid valve for high-pressure...
  • Page 22 Internal frost protection (optional) 1 Hand spray gun (2 tool version) 2 High pressure pump 3 Backflow valve with throttle and sieve 4 Solenoid valve with backflow valve, throttle and sieve 5 Backflow valve with mixing chamber for foam and pressure release valve 6 Hand-spray gun with washing brush (single tool version) 7 Receptacle...
  • Page 23 External frost protection (optional) 1 Hand spray gun (2 tool version) 2 High pressure pump 3 Backflow valve with throttle and sieve 4 Solenoid valve with backflow valve, throttle and sieve 5 Backflow valve with mixing chamber for foam and pressure release valve 6 Hand-spray gun with washing brush (single tool version) 7 Receptacle...
  • Page 24 – The motor protection switch interrupts the electric circuit if the motor is over- loaded. Hard water sensor SB MB standard: Washing station 3 and 4 not shown. If the residual hardness of the softened wa- ter exceeds a marginal value, the control...

  • Page 25: Technical Specifications

    Technical specifications SB MB 5/10-2 9/12- SB MB 5/10-3 9/12- 5/10-4 9/12- High-pressure module 608, 608fl Piece High pressure module 908 Piece Electrical connection Voltage V/~/Hz 400/3~/50 Maximum allowed net impedance 0.301 + j 0.188 Protection version CAB (SKID version)
  • Page 26 <2.5 Uncertainty K Sound pressure level L dB(A) Uncertainty K dB(A) Sound power level L + Uncertainty K dB(A) Dimensions SB MB CAB Width 2700 Depth Height 2100 Empty weight, max. (with 30 kg of packaging) 1100 Maximum weight 1750...
  • Page 27 Water type in the washing programme High-pressure wash Foam wash, wet foam Foam wash, dry foam Rinsing Hot wax Top care Dirt removal Micro emulsion A Micro emulsion B Insect removal Wheel cleaning A Wheel cleaning B Intensive foam Undercarriage X = Standard, O = Option, * processed water must be heated on site...

  • Page 28: Maintenance And Care

    Maintenance and care System overview 1 Balancing vessel * Depending on the equipment of the sys- Show system status 2 Fuel filter and fuel pump tem, the assembly intensive foam can be  In normal operating mode, press the 3 Burner inclusive flow-type heater attached in theses positions.
  • Page 30 Maintenance Trailing time of the circulation pump for Voltage supply to the remote controls. warm water after the burner has been Status WSO turned off. 1 Appliance component Status of washing stations 2 Time until next maintenance (minus symbol if maintenance is due) 3 Date of last maintenance Version / info ...
  • Page 31 Maintenance contract In order to ensure a reliable operation of the plant, we recommend that you conclude a maintenance contract with us. Please refer The salt solution in the salt tank is regener- Water level in the buffer container for per- to you local KÄRCHER service depart- ated.
  • Page 32 Maintenance schedule Time Activity Assembly affectedPerformance By whom once a year Clean the filter Antifreezing circula- Empty and clean the collection chute for the frost protection water. Operator/ before the tion Clean the filter on the immersion pump. Customer frosting peri- Clean the filter of the frost protection pump (in the casing of the SB Service od starts...
  • Page 33 With temperatures below 3°C, check if the trace heating of the heating Operator case of frost ing oil tank (option) oil line between the heating oil tank and SB MB is warm. Once, 1 Exchange filter Fine filter WSO Close the locking valve for fresh water (building site), unscrew the filter...
  • Page 34 Time Activity Assembly affectedPerformance By whom After 200 op- Check the operat- High-pressure The manometer must read 9...10 MPa (90...100 bars). Follow the in- Operator erating hours ing pressure pumps structions in the section "Help in the event of a malfunction" to repair or once a the defect if the reading is different.
  • Page 35 Clean looking glass for flame Maintenance Works monitoring Draining condensate at the compressor 1 Condensate drain valve  Hold the condensate drain valve over a 1 Oil container lid duct or a collection container. 2 Oil drain screw 1 Screw ...

  • Page 36: Troubleshooting

    Fault indication Troubleshooting in Switching Cabinet 1 Error display on display of control (in control cabinet) 1 Error display on the outside of the con- trol cabinet (only SB MB standard)
  • Page 37 Faults shown in the display Display Cause Remedy F 001 Electronic outlets overloaded Acknowledge the fault. If the fault recurs, call cus- tomer service. F 004 Dimming sensor defective Call customer service. F 005 Protective motor switch on high pressure pumps was triggered Reset motor protection switch;...
  • Page 38 Reset motor protection switch; call Customer Ser- vice if the problem recurs. F 200 No connection between the SB MB control and the electronics of the Call customer service. F 201 Outputs of the control SB MB to the WSO overloaded...
  • Page 39 Display Cause Remedy F 300 No connection to electronics A7 Acknowledge the fault. If the fault recurs, call cus- tomer service. F 301 Outputs of the electronics A7 overloaded F 320 No connection to electronics A8 F 321 Outputs of the electronics A8 overloaded F 322 Current consumption of pump for micro-emulsion (intensive cleaning complete) too high...
  • Page 40 Interruptions in warm water circulation Fault Possible cause Remedy By whom Low water level in Water supply blocked Open locking tap for fresh water Operator the swimmer tank Sieve in the water shortage safe guard is dirty Clean or replace the filter inlay. Operator for warm water Swimmer valve in the swimmer container for...
  • Page 41 Burner malfunctions with oil-heated devices 1 Unlocking key for exhaust gas thermo- stat 2 Unlock button of oil firing unit 3 Electrical box of burner control Fault Possible cause Remedy By whom Fault in oil firing (oil No ignition sparks exist (can be detected through Check electrode setting, ignition transformer and Customer Ser- firing unit) has trig-...
  • Page 42 Malfunctions at coin mechanism Fault Possible cause Remedy By whom All coin acceptors Main switch is switched off. Set main switch to “1”. Operator reject all coins Incorrectly adjusted time of day or operating Check the adjustments on the control. Operator times.
  • Page 43 Malfunctions on the wheel cleaner/intensive foam Fault Possible cause Remedy By whom Inadequate or no Sieve in the water inlet is dirty Clean sieve. Operator flow of water/deter- Nozzle insert in the injector clogged. Clean the nozzle insert. Operator gent Throttle in node piece obstructed.
  • Page 44 Interruptions in water preparation Fault Possible cause Remedy By whom Base exchanger is No power supply Check power supply (fuse, plug, switch). Operator/Cus- not regenerating tomer Service Hardness sensor defective Check hardness sensor, replace if required Customer Ser- vice Water remains No salt in the salt tank Refill salt, wait for brine formation (approx.
  • Page 45 Fault Possible cause Remedy By whom Permeate output is Water inlet temperature is too low Measure the temperature of the softened water and Operator too low; buffer tank compare it with the technical data. of permeate is often Operating pressure is too low Reset the operating pressure.

  • Page 46: Accessories

    Accessories Appliance care Wash hall and tile cleaner RM 841, 20 l Attachment sets Order no. : 6.295-419.0 Water filter G 1" Squeegee Order no. : 6.761-284.0 Order no. : 6.907-200.0 Test kits Spray bottle 1 l Test set A Order no.

  • Page 47: Installing The Unit (Only For Experts)

    Installing the unit (only for experts) Note:  After connecting the ssytem, check the Parameter Value The equipment may only be installed by rotating direction of the warm water cir- pH value 6.5...9.5 – KÄRCHER service engineers culation pump and the circulation pump electrical conductivity max.
  • Page 48 Connect the washing station heater Check oil level Turning the base exchanger on and start it up Backwash Note:  Inser the overflow hoses of base ex- The washing place heating can function changer and salt tank in the drainage properly provided the washing area has pipe of the building.
  • Page 49 Refill / Clean washing Check the function of the system  Press the programme button and select  Check burner setting. the function "Fill+Rinse clear" by turn-  Check all functions of the system. ing the button in the direction of the ar- ...
  • Page 50 Dimension drawing for CAB model * SB MB standard ** SB MB comfort...
  • Page 51 Dimension drawing for SKID model * SB MB standard ** SB MB comfort...
  • Page 52 Dimension drawing for SKID model with WSO upgrade kit...
  • Page 53 EU Declaration of Conformity We hereby declare that the machine de- scribed below complies with the relevant basic safety and health requirements of the EU Directives, both in its basic design and construction as well as in the version put into circulation by us.

  • Page 54: Log Of High Pressure Testing

    Log of high pressure testing Plant type: Manufact. no.: Start-up on: Testing done on: Findings: Signature Testing done on: Findings: Signature Testing done on: Findings: Signature Testing done on: Findings: Signature...

Table of Contents

Save PDF