Reversing The Doors - Beko FROST FREE COMBI CDA 647 F Installation & Operation Instructions

REVERSING THE DOORS

We recommend that you reverse doors before switching on for the first time.
Tools required: Small and medium size flat and cross-headed screwdrivers, a pair of pliers.
Spare Parts supplied in the plastic bag: The following parts, which are exclusively for left hand side fitted hinge operation
are supplied in a plastic bag with the appliance:
- Upper door top trim hinge covers – there are 2 different parts, one for each side of top trim.
- Upper door middle hinge bushing/door stopper assembly.
We suggest you keep all the parts supplied in the plastic bag and also parts, which have been removed when reversing
doors, in a safe place for possible future, re-use.
IMPORTANT: We suggest you ask somebody to help you when moving the appliance around and to hold doors when
removing / re-fitting hinges and doors to avoid any injury and damage to the product.
Please refer to diagrams supplied. To follow numbers in brackets below, refer to the main diagram.
1. Switch off the appliance at the socket outlet and pull out the mains plug.
2. Remove all loose items and fittings and food, if any, from inside the appliance and door racks.
3. Gently prise off plastic hinge covers on both sides of upper door top trim and front top panel using a small
flat-headed screwdriver. (1)
4. Gently tilt the appliance back against a strong wall on its rear side sufficiently to allow the lower hinge to be
removed. Take care to protect the appliance, your wall and floor coverings. You can utilise the original
packaging to do this. Once you tilt the appliance back, check to make sure the appliance is completely
stable and safe before you carry on. (2)
5. Unscrew and remove the lower hinge using a cross-headed screwdriver while holding the lower door
firmly.(3)
6. Remove lower door carefully off the middle hinge and stand door upright in a safe place.(4)
7. Open upper door and unscrew and remove the middle hinge while holding the upper door firmly. Use a
flat-headed screwdriver. Middle hinge will need to be rotated 180 degrees before re-fitting on the opposite
side.(5)
8. Remove upper door carefully off the upper hinge and stand door upright in a safe place.(6)
9. Unscrew and remove the upper hinge using a flat-headed screwdriver.(7)
10. Rotate the upper hinge 180 degrees and then unscrew and remove the hinge pin using a pair of pliers and re-fit to
opposite side of hinge.(8)
11. Reposition plugs and hinge pin bushings on top of doors on the opposite side of both doors. Use small flat-
headed screwdrivers to remove plugs and bushings. Take care not to mark doors.(9)
12. Reposition left hand side feet on the opposite side. Unscrew and reposition the bottom hinge bushing. (10)
13. Unscrew and remove the upper door middle hinge pin bushing/door stopper using a cross-headed
screwdriver. Important: This part cannot be used on the opposite side; left hand side middle hinge pin
bushing/door stopper part is supplied in the plastic bag.(11)
14. Re-fit the upper hinge on the left hand side using flat-headed screwdriver.(12)
15. Fit upper door left hand side middle hinge pin bushing/door stopper supplied in the plastic bag using
cross-headed screwdriver.(13)
16. Reposition three small plastic plugs on the left hand side, which are covering middle hinge holes, on the
opposite side to cover holes left empty.(14)
17. Locate and re-fit upper door to upper hinge and hold the door firmly.(15)
18. Locate the middle hinge pin to middle hinge pin bushing of upper door on the left hand side and re-fit the
middle hinge.(16)
19. Reposition the two screws fitted to lower hinge holes on the left hand side at the bottom of the cabinet on
the opposite side.(17)
20. Locate and re-fit lower door to middle hinge pin and then re-fit the lower hinge on the left hand side.(18), (19)
21. Carefully stand the appliance upright and adjust the two front feet if necessary.
22. Check that doors open and close easily, they are aligned correctly and that there are no gaps allowing
air into the cabinet. If there are gaps between the door seal and the cabinet, adjust the door seal by gently
pulling away from the door using fingers.
23. Check that all the hinge screws are tightened. Avoid over tightening the screws.
24. Put all items, fittings back in the appliance.
25. Fit upper door top trim and front top panel plastic hinge covers. Upper door top trim hinge covers are
supplied in the plastic bag.(20)
26. Wait for at least 4 hours to allow the system to settle before switching on.
27. Once the correct storage temperatures have been reached in the appliance, put back all the food.
7
(8)
1
1
2
5
14
45 °
4
3
10
20
12
8
180°
20
16
17
19
8
(13)
20
7
1
6
11
13
9
10
15
18