Hints For Timer Recording - Sharp DV-SR45U Operation Manual

Hints for timer recording

• If there is a power failure or this unit has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost.
• If a disc is not on the tray, the
• When all the timer recording is completed, the
button first, and then press PLAY B or OPEN/CLOSE A button.
• During timer recording or timer standby (
available.To make these operations available, cancel the timer recording or timer standby first (
• To cancel the timer standby mode, press POWER button.
• When the Start and the End time are the same, the length of the recording will be set for 24 hours.When the disc
reaches at the end during the recording, the DVD recorder turns itself off.
• When the programmed Start and End time are earlier than the current time, the recording will be set on the same date in the next year.
• If your programmed Start time is within 2 minutes from the current time, the power will turn on for recording standby
right after you turn the power off.
• If the Start time is earlier and the End time is later than the current time, the recording will start right after you turn
the power off.
The priority of overlapped settings
This unit records the programs according to priority if the timer programmings are overlapped.The timer programming
set previously has priority.
A timer recording of lower priority will be canceled, start from the middle or stop on the way.
Check the overlapped timer programmings and change the priority if necessary.
A programming set previously has priority
When the starting time is the same:
A program set previously (PROG. 1) has priority.
ex.1
PROG. 1
PROG. 2
Actual
PROG. 1
recording
The first 30 seconds (at the longest) will be cut off
When the recording time is partially overlapped:
PROG. 1 will start after PROG. 2 is complete to be recorded.
However, PROG. 1 will be recorded if you turn the power off for timer standby within 2 minutes
to the Start time for PROG. 1.
PROG. 1
PROG. 2
Actual
PROG. 2
recording
The first 30 seconds (at the longest) will be cut off
When the recording time is entirely overlapped:
However, if you turn the power off for timer standby within 2 minutes
to the Start time for PROG. 1, PROG. 1 will be recorded first, and the
recording of PROG. 2 will start after the recording of PROG. 1 is completed.
PROG. 1
PROG. 2
Actual
recording
When the End time of the programming currently being recorded and the Start time
of the subsequent program are same:
If PROG. 1 is a DVD recording program, the beginning of the PROG. 2 may be cut off.
The amount of time cut off differs depending on the recorded media.
For example, if both PROG. 1 and PROG. 2 are DVD recordings, the first 30 seconds (at the longest) will be cut off PROG.
PROG. 1
PROG. 2
Actual
PROG. 1
recording
36
Recording
Timer recording (cont'd)
indicator flashes and timer recording cannot be performed. Please insert a recordable disc.
indicator flashes.To play or eject the recorded disc, press POWER
indicator is on the front display), any operations on the unit will not be
ex. 2
PROG. 1
PROG. 2
PROG. 3
Actual
PROG. 2
recording
The first 30 seconds (at the longest) will be cut off
PROG. 1
PROG. 2
PROG. 2
The first 30 seconds (at the longest) will be cut off.
When some programming have been
made at the end time of the
programming currently being recorded:
A program set previously (PROG. 2) has priority.
PROG. 1
Note
• When the recording time of
two programs are overlapped,
or the End time of a program
and the Start time of another
is the same, the first 30 sec-
onds (at the longest) of the
subsequent program will be
cut off.
indicator disappears).
PROG. 2